Aashranth Bommakanti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Aashranth Bommakanti has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Utpal Borah
Indira Gandhi Centre for Atomic Research
14 shared publications- Dipti Samantaray
Indira Gandhi Centre for Atomic Research
12 shared publications - Santosh Kumar
Indira Gandhi Centre for Atomic Research
11 shared publications M. Arvinth Davinci
Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, India
10 shared publicationsDipti Samantaray
Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, India
8 shared publicationsA. K. Bhaduri
Indira Gandhi Centre for Atomic Research
6 shared publications
Latest Publications
- Open Access
- 17 April 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Engineering
- Vol. 20 (1) , 1-16
Dynamic transformation as a tool to enhance the cold-working response of a 9% Cr steel through stress and strain partitioning
Dynamic transformation in a 9% Cr steel is shown to improve the room-temperature workability through microstructural modification. The dynamically transformed microstructure contains 10–18% of ductile ferrite in a brittle martensitic matrix. The two-phase microstructure results in 40% higher uniform elongation and 25% lower tensile strength, which facilitate cold working. Further, the presence of ductile ferrite is shown to increase the strain hardening exponent, further enhancing the workability. It is also shown that the dynamic transformation alters the martensitic matrix, and creates a secondary source of softening. These softening effects and overall mechanical response are accurately modelled by a robust modified rule-of-mixtures formulation with prediction error of ~ 0.3%. This investigation reveals the potential of dynamic transformation to create intermediate microstructures suitable for cold working during the manufacturing process and establishes the limits within which deformation can be safely imparted.
- 17 April 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Engineering
- Vol. 20 (1) , 1-16
Open AccessDynamic transformation as a tool to enhance the cold-working response of a 9% Cr steel through stress and strain partitioning
Dynamic transformation in a 9% Cr steel is shown to improve the room-temperature workability through microstructural modification. The dynamically transformed microstructure contains 10–18% of ductile ferrite in a brittle martensitic matrix. The two-phase microstructure results in 40% higher uniform elongation and 25% lower tensile strength, which facilitate cold working. Further, the presence of ductile ferrite is shown to increase the strain hardening exponent, further enhancing the workability. It is also shown that the dynamic transformation alters the martensitic matrix, and creates a secondary source of softening. These softening effects and overall mechanical response are accurately modelled by a robust modified rule-of-mixtures formulation with prediction error of ~ 0.3%. This investigation reveals the potential of dynamic transformation to create intermediate microstructures suitable for cold working during the manufacturing process and establishes the limits within which deformation can be safely imparted.
- 5 May 2023
- Published by Springer Nature in JOM
- Vol. 75 (8) , 3136-3148
Scale-Invariant Geometries Arising from the Interaction Between a 9%Cr Steel and Molten Nitrate Salt
- 5 May 2023
- Published by Springer Nature in JOM
- Vol. 75 (8) , 3136-3148
Scale-Invariant Geometries Arising from the Interaction Between a 9%Cr Steel and Molten Nitrate Salt
- 27 December 2022
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 12 (1) , 49-61
Improvements in the Metallography of Ferritic–Martensitic Steels Through a Color Etching Procedure
- 27 December 2022
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 12 (1) , 49-61
Improvements in the Metallography of Ferritic–Martensitic Steels Through a Color Etching Procedure
- 1 September 2020
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 144
Disengagement of dispersed cerium oxalate from nitric-oxalic acid medium in a batch settler: Measurements and CFD simulations
- 1 September 2020
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 144
Disengagement of dispersed cerium oxalate from nitric-oxalic acid medium in a batch settler: Measurements and CFD simulations
- 1 June 2020
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 73 (6) , 1637-1643
Influence of Large Strain Hot Deformation on Microstructural Evolution in Alloy D9
- 1 June 2020
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 73 (6) , 1637-1643
Influence of Large Strain Hot Deformation on Microstructural Evolution in Alloy D9
- 22 January 2020
- Published by Springer Nature in JOM
- Vol. 72 (3) , 1395-1405
Formation of Deformation Bands in Hot-Worked SS 316LN
- 22 January 2020
- Published by Springer Nature in JOM
- Vol. 72 (3) , 1395-1405
Formation of Deformation Bands in Hot-Worked SS 316LN
- 4 June 2019
- Published by Springer Nature in JOM
- Vol. 71 (8) , 2705-2710
Integrated Experimental-Modelling Strategy to Understand Dislocation–Defect Interactions During Hot Working of Face-Centred Cubic Alloys
- 4 June 2019
- Published by Springer Nature in JOM
- Vol. 71 (8) , 2705-2710
Integrated Experimental-Modelling Strategy to Understand Dislocation–Defect Interactions During Hot Working of Face-Centred Cubic Alloys
- 1 May 2019
- Published by ASTM International in Materials Performance and Characterization
- Vol. 8 (5) , 957-968
Warm Working as a Potential Substitute for Hot Working of Austenitic Steel in Selected Applications
The conventional manufacturing route for austenitic steels involves casting, ingot breakdown, subsequent hot working, and finally cold working, with numerous intermediate heat treatment stages. In this study, the potential of warm working to substitute some steps of the conventional manufacturing process is examined. A low-carbon austenitic stainless steel, SS304L, is subjected to cold, warm, and hot deformation in light of recent understanding of warm working. The deformation response in these two regimes is compared on the basis of metallurgical, mechanical, and process variables. Metallurgical response is compared on the basis of resultant grain size and stability of microstructure to subsequent heat treatment. The differences in mechanical response in the two regimes are evaluated through analysis of flow curves. Finally, the important but often ignored parameter of process stability is examined by performing nonisothermal deformation and examining the effect on microstructure. The results are used to propose some applications where warm working can substitute hot and cold working.
- 1 May 2019
- Published by ASTM International in Materials Performance and Characterization
- Vol. 8 (5) , 957-968
Warm Working as a Potential Substitute for Hot Working of Austenitic Steel in Selected Applications
The conventional manufacturing route for austenitic steels involves casting, ingot breakdown, subsequent hot working, and finally cold working, with numerous intermediate heat treatment stages. In this study, the potential of warm working to substitute some steps of the conventional manufacturing process is examined. A low-carbon austenitic stainless steel, SS304L, is subjected to cold, warm, and hot deformation in light of recent understanding of warm working. The deformation response in these two regimes is compared on the basis of metallurgical, mechanical, and process variables. Metallurgical response is compared on the basis of resultant grain size and stability of microstructure to subsequent heat treatment. The differences in mechanical response in the two regimes are evaluated through analysis of flow curves. Finally, the important but often ignored parameter of process stability is examined by performing nonisothermal deformation and examining the effect on microstructure. The results are used to propose some applications where warm working can substitute hot and cold working.
- 1 May 2019
- Published by ASTM International in Materials Performance and Characterization
- Vol. 8 (5) , 796-807
Investigation on Grain Boundary Character Distribution During Dynamic Recrystallization of Austenitic Stainless Steel During Hot Deformation
The phenomenon of dynamic recrystallization (DRX) is central to the hot working and thermomechanical processing of austenitic stainless steel. This study aims to relate two distinct parameters that influence DRX: the content of interstitial atoms, such as nitrogen, and character of grain boundaries in the steel. 316LN austenitic stainless steel has been subjected to thermomechanical processing at 1,423 K through uniaxial compression at different strain rates. At these, the microstructure is fully recrystallized. The nature, character, and growth of DRX grains are studied using Electron Backscatter Diffraction (EBSD). EBSD is used to determine grain boundary character distribution and the Effective Grain Boundary Energy (EGBE) parameter. The evolution of EGBE and its relation to grain growth are analyzed. The concomitant development of special low-energy boundaries is correlated with the interstitial content in the steel, thus linking interstitial content to EGBE. The correlations so made are tested by examining the corrosion resistance of different boundaries formed at different deformation conditions.
- 1 May 2019
- Published by ASTM International in Materials Performance and Characterization
- Vol. 8 (5) , 796-807
Investigation on Grain Boundary Character Distribution During Dynamic Recrystallization of Austenitic Stainless Steel During Hot Deformation
The phenomenon of dynamic recrystallization (DRX) is central to the hot working and thermomechanical processing of austenitic stainless steel. This study aims to relate two distinct parameters that influence DRX: the content of interstitial atoms, such as nitrogen, and character of grain boundaries in the steel. 316LN austenitic stainless steel has been subjected to thermomechanical processing at 1,423 K through uniaxial compression at different strain rates. At these, the microstructure is fully recrystallized. The nature, character, and growth of DRX grains are studied using Electron Backscatter Diffraction (EBSD). EBSD is used to determine grain boundary character distribution and the Effective Grain Boundary Energy (EGBE) parameter. The evolution of EGBE and its relation to grain growth are analyzed. The concomitant development of special low-energy boundaries is correlated with the interstitial content in the steel, thus linking interstitial content to EGBE. The correlations so made are tested by examining the corrosion resistance of different boundaries formed at different deformation conditions.
- 23 January 2019
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 72 (6) , 1489-1492
Investigation on Low-Temperature Deformation Behaviour of Molybdenum Under Compressive Loading
- 23 January 2019
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 72 (6) , 1489-1492
Investigation on Low-Temperature Deformation Behaviour of Molybdenum Under Compressive Loading