Andrii Titov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrii Titov has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Dusan Janickovic
Institute of Physics, Slovak Academy of Sciences
2 shared publications - Ondrej Zivotsky
Department of Physics, VŠB-Technical University of Ostrava, 17 listopadu 15/2172, 708 33 Ostrava-Poruba, Czech Republic
2 shared publications - Yvonna Jiraskova
CEITEC IPM, Institute of Physics of Materials, AS CR, Zizkova 22, 616 00 Brno, Czech Republic
2 shared publications J. Bursik
Institute of Physics of Materials, AS CR 3 , Brno 616 62, Czech Republic
1 shared publicationJiří Buršík
1 shared publication
Latest Publications
- 1 April 2019
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 475, 5-9
Low-temperature magnetic transitions in Fe2MnSi Heusler alloys prepared in bulk and ribbon form
- 1 April 2019
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 475, 5-9
Low-temperature magnetic transitions in Fe2MnSi Heusler alloys prepared in bulk and ribbon form
- Open Access
- 19 October 2017
- Published by AIP Publishing in AIP Advances
- Vol. 8 (4)
Microstructure and magnetism of Co2FeAl Heusler alloy prepared by arc and induction melting compared with planar flow casting
This paper is devoted to investigations of the structural and magnetic properties of the Co2FeAl Heusler alloy produced by three technologies. The alloys prepared by arc and induction melting have resulted in coarse-grained samples in contrast to the fine-grained ribbon-type sample prepared by planar flow casting. Scanning electron microscopy completed by energy dispersive X-ray spectroscopy, X-ray diffraction, Mössbauer spectroscopy, and magnetic methods sensitive to both bulk and surface were applied. The chemical composition was slightly different from the nominal only for the ribbon sample. From the viewpoint of magnetic properties, the bulk coercivity and remnant magnetization have followed the structure influenced by the technology used. Saturation magnetization was practically the same for samples prepared by arc and induction melting, whereas the magnetization of ribbon is slightly lower due to a higher Al content at the expense of iron and cobalt. The surface magnetic properties were markedly influenced by anisotropy, grain size, and surface roughness of the samples. The surface roughness and brittleness of the ribbon-type sample did not make domain structure observation possible. The other two samples could be well polished and their highly smooth surface has enabled domain structure visualization by both magneto-optical Kerr microscopy and magnetic force microscopy.
- 19 October 2017
- Published by AIP Publishing in AIP Advances
- Vol. 8 (4)
Open AccessMicrostructure and magnetism of Co2FeAl Heusler alloy prepared by arc and induction melting compared with planar flow casting
This paper is devoted to investigations of the structural and magnetic properties of the Co2FeAl Heusler alloy produced by three technologies. The alloys prepared by arc and induction melting have resulted in coarse-grained samples in contrast to the fine-grained ribbon-type sample prepared by planar flow casting. Scanning electron microscopy completed by energy dispersive X-ray spectroscopy, X-ray diffraction, Mössbauer spectroscopy, and magnetic methods sensitive to both bulk and surface were applied. The chemical composition was slightly different from the nominal only for the ribbon sample. From the viewpoint of magnetic properties, the bulk coercivity and remnant magnetization have followed the structure influenced by the technology used. Saturation magnetization was practically the same for samples prepared by arc and induction melting, whereas the magnetization of ribbon is slightly lower due to a higher Al content at the expense of iron and cobalt. The surface magnetic properties were markedly influenced by anisotropy, grain size, and surface roughness of the samples. The surface roughness and brittleness of the ribbon-type sample did not make domain structure observation possible. The other two samples could be well polished and their highly smooth surface has enabled domain structure visualization by both magneto-optical Kerr microscopy and magnetic force microscopy.