YIYaroslav Ignatenko

Yaroslav Ignatenko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yaroslav Ignatenko has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Turbulent spiral flow of power-law fluid in annular channel

    by Yaroslav Ignatenko, Andrey Gavrilov, Oleg B. Bocharov, Roger Aragall


  • Open Access

    Characteristics of a Particle’s Incipient Motion from a Rough Wall in Shear Flow of Herschel–Bulkley Fluid

    by Alexander Seryakov, Yaroslav Ignatenko, Oleg B. Bocharov

    A numerical simulation of the Herschel–Bulkley laminar steady state shear flow around a stationary particle located on a sedimentation layer was carried out. The surface of the sedimentation layer was formed by hemispheres of the same radius as the particle. The drag force, lift force, and torque values were obtained in the following ranges: shear Reynolds numbers for a particle ReSH=2–200, corresponding to laminar flow; power law index n=0.6–1.0; and Bingham number Bn=0–10. A significant difference in the forces and torque acting on a particle in shear flow in comparison to the case of a smooth wall is shown. It is shown that the drag coefficient is on average 6% higher compared to a smooth wall for a Newtonian fluid but decreases with the increase in non-Newtonian properties. At the edge values of n=0.6 and Bn=10, the drag is on average 25% lower compared to the smooth wall. For a Newtonian fluid, the lift coefficient is on average 30% higher compared to a smooth wall. It also decreases with the increase in non-Newtonian properties of the fluid, but at the edge values of n=0.6 and Bn=10, it is on average only 3% lower compared to the smooth wall. Approximation functions for the drag, lift force, and torque coefficient are constructed. A reduction in the drag force and lifting force leads to an increase in critical stresses (Shields number) on the wall on average by 10% for incipient motion (rolling) and by 12% for particle detachment from the sedimentation bed.


  • Open Access

    Numerical Simulation of Taylor—Couette—Poiseuille Flow at Re = 10,000

    by Andrey Gavrilov, Yaroslav Ignatenko

    A fully developed turbulent flow in a concentric annulus, Re =10,000, ri/ro=0.5, with an inner rotating cylinder in the velocity range N=Uω/Ub=0÷4, is studied via a large-eddy simulation. Also, for comparison, simulations by steady-state, unstatiounary RANS k-ω SST (URANS), and Elliptic Blending Model (EBM) were made. The main focus of this study is on the effect of high rotation on the mean flow, turbulence statistics, and vortex structure. Distribution of the tangential velocity and the Reynolds stress tensor change their behaviour at N>0.5∼1. With rotation increases, the production of tangential fluctuation becomes dominant over axial ones and the position of turbulent kinetic energy maximum shifts towards the wall into the buffer zone. URANS and EBM approaches show good agreement with LES in mean flow, turbulent statistics, and integral parameters. The difference in pressure loss prediction between LES and URANS does not exceed 20%, but the average difference is about 11%. The EBM approach underestimates pressure losses up to 9% and on average not more than 5%. Vortex structures are described well by URANS.


  • Open Access

    On the modes of cuttings transport in an inclined annular channel

    by Ya Ignatenko, A Gavrilov, O Bocharov, R May

    The paper presents the results of the simulation of cuttings transport (solid spherical particles) by water through a long annular axisymmetric inclined channel. At the inlet uniform distribution of particles and fluid velocity was set. Inclination angle varied from 0 to 90 degrees. Modes of stationary and moving dunes and their transition into wave-shaped and stationary sediment were observed. Moving dunes could oscillate laterally and did not form a crest that occupied the entire width of the channel. In this case, dense sediment formed an S-shaped path, moving along the stream. Despite the general downstream movement of the S-shaped track (dune), a downward flow might occur in the low area with high concentration. Five basic flow regimes were identified: constant sediment, moving wave-like sediment, separated stationary dunes, S-shaped sediment and homogeneous flow. The basic flow pattern could be complicated by lateral motion and backward flow in a region of high concentration. A variant of the flow pattern map is suggested.

  • Cuttings Transport Simulation in Large-Diameter Inclined Borehole

    by Yaroslav Ignatenko, Andrey Gavrilov, Oleg Bocharov, Roland May

    An Eulerian mixture model of the two-phase flow was used for cuttings transport simulation. The model was tested using experimental data for particles transport in pipes. Three types of problem statements were analyzed: steady-state flow, non-stationary flow in a short-length channel with periodic boundary conditions, and non-stationary flow in a long channel. Simulation of cuttings transport by Herschel-Bulkley fluid through an inclined 21-inch borehole/–6.5-inch drillpipe annulus was performed. All problem statements showed very close results, even for unsteady flow. These results demonstrated the applicability of 2D steady-state problem formulation for cuttings transport simulation. The unsteady flow was observed for an inclination of less than 20 degrees. Slow downward sliding of cuttings in the lower part of inclined boreholes was observed simultaneously with upstream dunes movement. Drill pipe rotation significantly decreased the cuttings concentration and pressure gradient, and shifted the maximum cuttings transport downward sliding rate from a 20- to 40-degree inclination.


  • Open Access

    Simulation of steady-state cuttings transport through a horizontal annulus channel

    by Yaroslav Ignatenko, Andrey Gavrilov, Oleg Bocharov, Roland May

    The current study is devoted to simulating cuttings transport by drilling fluid through a horizontal section of borehole with an annular cross section. Drill pipe rotates in fixed eccentric position. Steady-state flow is considered. Cuttings are rigid spheres with equal diameters. The carrying fluid is drilling mud with Herschel-Bulkley rheology. Suspension rheology depends on local shear rate and particles concentration. Continuous mixture model with algebraic equation for particles slipping velocity is used. Two hydrodynamic regimes are considered: axial flow without drill pipe rotation and with drill pipe rotation. In the case of axial flow was shown that increasing of power index n and consistency factor k increases pressure gradient and decreases cuttings concentration. Increasing of yield stress leads to increasing of pressure gradient and cuttings concentration. Cuttings concentration achieves constant value for high yield stress and not depends on it. Rotation of the drill pipe significantly changes the flow structure: pressure loss occurs and particles concentration decreases in the cross section. Two basic regimes of rotational flow are observed: domination of primary vortex around drill pipe and domination secondary vorticity structures. Transition between regimes leads to significant changes of flow integral parameters.


  • Open Access

    Lift and Drag Forces for a Sphere on a Flat Wall in Non-Newtonian Shear Flow

    by Yaroslav Ignatenko, Oleg Bocharov, Roland May

    Parametrical study of perfect steady rolling and steady state freely motion of spherical particle on the wall in shear flow of non-Newtonian fluid was carried out. In the case of perfect rolling the jumps of forces acting on a sphere in the moment of changing particle velocity from zero to positive were observed. Non-Newtonian properties of fluid lead to decreasing of drag force coefficient for low particle's velocity and to opposite effect for high velocity relative to Newtonian fluid. There is no such significant effect for a lift force coefficient. Steady state particle's velocity (Fd(Vpss)=0) increases for non-Newtonian fluid for both considered types of motion. Steady state particle's velocity and lift force coefficient are lower for the case of freely particle motion. Steady state rotational velocity decreases for non-Newtonian fluid.