Erol Türkeş
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Erol Türkeş has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Arif Gök
Department of Industrial Design Kutahya Dumlupinar University Kutahya Turkey
1 shared publication - Evren Çağlarer
Kırklareli Üniversitesi, Teknoloji Fakültesi
1 shared publication - Hayrettin Toylan
Kirklareli University
1 shared publication İlyas İstif
1 shared publication- Kadir Gök
İzmir Bakırçay University
1 shared publication - Kamil Feratoğlu
Kirklareli University
1 shared publication
Latest Publications
- Open Access
- 24 January 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (1) , 27-34
Determination of the construction material for phononic band gap structures by tribological performance
This study investigates the tribological performances of commonly used stainless steel alloys (303, 304, 316L, and 420) to determine their suitability as construction materials for periodic structures designed for inertial amplification induced phononic band gap vibration isolators. Stainless steel alloys are extensively employed in engineering structures due to their ability to withstand large stresses and exhibit excellent cyclic loading properties. In this study, stainless steel specimens are examined by dry and lubricated wear test conditions. 420 stainless steel showed highest wear resistant properties for dry and lubricated conditions. Two grades of lubricants are compared in terms of viscosities, and it is revealed that higher viscosity blocked the flow of the lubricant so that semi-dry friction occurred. Low viscosity lubricant enabled less material removal due to friction.
- 24 January 2025
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 28 (1) , 27-34
Open AccessDetermination of the construction material for phononic band gap structures by tribological performance
This study investigates the tribological performances of commonly used stainless steel alloys (303, 304, 316L, and 420) to determine their suitability as construction materials for periodic structures designed for inertial amplification induced phononic band gap vibration isolators. Stainless steel alloys are extensively employed in engineering structures due to their ability to withstand large stresses and exhibit excellent cyclic loading properties. In this study, stainless steel specimens are examined by dry and lubricated wear test conditions. 420 stainless steel showed highest wear resistant properties for dry and lubricated conditions. Two grades of lubricants are compared in terms of viscosities, and it is revealed that higher viscosity blocked the flow of the lubricant so that semi-dry friction occurred. Low viscosity lubricant enabled less material removal due to friction.
- Open Access
- 31 December 2024
- Published by Kirklareli Universitesi Muhendislik ve Fen Bilimleri Dergisi in Kırklareli Üniversitesi Mühendislik ve Fen Bilimleri Dergisi
- Vol. 10 (2) , 363-376
Sabit Kanatlı İHA’da Kanat Geometrisinin Aerodinamikteki Etkileri
Hava araçlarının tümünde tüketilen yakıt miktarını azaltmak, faydalı yükü arttırmak için gövdenin ve kanatların geometrisinde değişiklikler yapılmaktadır. Bu makale çalışmasında da sabit kanatlı İHA’lar ve kanatlarında CL/CD oranını arttırmak hedeflenmiştir. Üç farklı kanat modeli (NACA-0012, NACA-4415 ve SD-7037) ve yeni bir kanat olan ALTAY kanadı ön tasarımları ve aerodinamik analizleri XFLR5 programında analiz edildi. Kanatların XFLR5 ve ANSYS Fluent programındaki analizleri üç farklı Reynolds sayısında (50 000; 150 000 ve 250 000) ve beş farklı hücum açısındaki (-5°; 0°; 5°; 10° ve 15°) ortam şartlarında gerçekleştirilmiştir. SOLİDWORKS öğrenci programında ALTAY ile SD-7037 kanatları üç boyutlu olarak tasarımları yapılıp 3D yazıcıda üretilmiştir. SOLİDWORKS programında biri düz kanatlı diğeri ise dik trapez kanalı iki adet İHA tasarlanıp, ANSYS Fluent programında Akış hızının (15,5 m/s) olduğu beş farklı hücum açısındaki (-5°; 0°; 5°; 10° ve 15°) ortam şartlarında aerodinamik analizleri gerçekleştirilmiştir. Analiz sonuçlarında ALTAY kanadının SD-7037 kanadına göre daha verimli olduğu, dik trapez kanatlı İHA’nın da düz kanada göre daha verimli olduğu sonucuna varılmıştır.
- 31 December 2024
- Published by Kirklareli Universitesi Muhendislik ve Fen Bilimleri Dergisi in Kırklareli Üniversitesi Mühendislik ve Fen Bilimleri Dergisi
- Vol. 10 (2) , 363-376
Open AccessSabit Kanatlı İHA’da Kanat Geometrisinin Aerodinamikteki Etkileri
Hava araçlarının tümünde tüketilen yakıt miktarını azaltmak, faydalı yükü arttırmak için gövdenin ve kanatların geometrisinde değişiklikler yapılmaktadır. Bu makale çalışmasında da sabit kanatlı İHA’lar ve kanatlarında CL/CD oranını arttırmak hedeflenmiştir. Üç farklı kanat modeli (NACA-0012, NACA-4415 ve SD-7037) ve yeni bir kanat olan ALTAY kanadı ön tasarımları ve aerodinamik analizleri XFLR5 programında analiz edildi. Kanatların XFLR5 ve ANSYS Fluent programındaki analizleri üç farklı Reynolds sayısında (50 000; 150 000 ve 250 000) ve beş farklı hücum açısındaki (-5°; 0°; 5°; 10° ve 15°) ortam şartlarında gerçekleştirilmiştir. SOLİDWORKS öğrenci programında ALTAY ile SD-7037 kanatları üç boyutlu olarak tasarımları yapılıp 3D yazıcıda üretilmiştir. SOLİDWORKS programında biri düz kanatlı diğeri ise dik trapez kanalı iki adet İHA tasarlanıp, ANSYS Fluent programında Akış hızının (15,5 m/s) olduğu beş farklı hücum açısındaki (-5°; 0°; 5°; 10° ve 15°) ortam şartlarında aerodinamik analizleri gerçekleştirilmiştir. Analiz sonuçlarında ALTAY kanadının SD-7037 kanadına göre daha verimli olduğu, dik trapez kanatlı İHA’nın da düz kanada göre daha verimli olduğu sonucuna varılmıştır.
- Open Access
- 13 March 2024
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 49 (11) , 14927-14948
Effect of Carbon Nanotube Reinforcement on Creep and Recovery Behavior of Additively Manufactured Polymers: An Experimental and Prediction Study
In this study, one of the most frequently used polymeric materials in fused deposition modeling (FDM) acrylonitrile butadiene styrene (ABS) is reinforced with different amount of carbon nanotubes (CNTs). Thermogravimetric analysis and differential scanning calorimetry analysis are applied to examine thermal degradation behavior of produced nanocomposite filaments. Specimens are manufactured by fused deposition modeling by using produced nanocomposite filaments. Tensile, creep and viscoelastic-viscoplastic behaviors of FDM-printed nanocomposite samples are investigated by conducting tensile, creep and loading–unloading tests under different strain rates and strain levels. Morphology of 3D printed samples is examined through scanning electron microscopy. Void densities which plays important role in mechanical behavior of additively manufactured samples are determined via ImageJ and CNT reinforcement on void densities are investigated. Data obtained from tests are used in system identification process, and multi-input–single-output model structures are proposed for the prediction of tensile, creep and recovery behaviors of 3D printed nanocomposite materials.
- 13 March 2024
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 49 (11) , 14927-14948
Open AccessEffect of Carbon Nanotube Reinforcement on Creep and Recovery Behavior of Additively Manufactured Polymers: An Experimental and Prediction Study
In this study, one of the most frequently used polymeric materials in fused deposition modeling (FDM) acrylonitrile butadiene styrene (ABS) is reinforced with different amount of carbon nanotubes (CNTs). Thermogravimetric analysis and differential scanning calorimetry analysis are applied to examine thermal degradation behavior of produced nanocomposite filaments. Specimens are manufactured by fused deposition modeling by using produced nanocomposite filaments. Tensile, creep and viscoelastic-viscoplastic behaviors of FDM-printed nanocomposite samples are investigated by conducting tensile, creep and loading–unloading tests under different strain rates and strain levels. Morphology of 3D printed samples is examined through scanning electron microscopy. Void densities which plays important role in mechanical behavior of additively manufactured samples are determined via ImageJ and CNT reinforcement on void densities are investigated. Data obtained from tests are used in system identification process, and multi-input–single-output model structures are proposed for the prediction of tensile, creep and recovery behaviors of 3D printed nanocomposite materials.
- Open Access
- 1 March 2023
- Published by Bilingual Publishing Group in Journal of Metallic Material Research
- Vol. 6 (1) , 16-24
Analyzing the Effects of Tool Holder Stiffness on Chatter Vibration Reduction in Turning
This paper investigates the effects of tool holder materials on chatter vibration in turning operations. The study uses a complex dynamic turning model with two degrees of freedom for the orthogonal cutting system. Tool holders made from different materials, including Al 5083, Al 6082, Al 7012, and a standard 4140 material, were subjected to chatter vibration to investigate their process damping capabilities. The study found that the standard tool holder 4140 allows for higher stable depths of cut and produces similar process damping values compared to the other tool holders. Finite element analyses (FEA) were performed to verify the experimental results, and the modal and FEA analyses produced very similar results. The study concludes that future research should investigate the effects of tool holders made from high alloy steel alloys on process damping. Overall, this paper provides important insights into the effects of tool holder materials on chatter vibration and process damping in turning operations, which can help in the design of more efficient and effective cutting systems.
- 1 March 2023
- Published by Bilingual Publishing Group in Journal of Metallic Material Research
- Vol. 6 (1) , 16-24
Open AccessAnalyzing the Effects of Tool Holder Stiffness on Chatter Vibration Reduction in Turning
This paper investigates the effects of tool holder materials on chatter vibration in turning operations. The study uses a complex dynamic turning model with two degrees of freedom for the orthogonal cutting system. Tool holders made from different materials, including Al 5083, Al 6082, Al 7012, and a standard 4140 material, were subjected to chatter vibration to investigate their process damping capabilities. The study found that the standard tool holder 4140 allows for higher stable depths of cut and produces similar process damping values compared to the other tool holders. Finite element analyses (FEA) were performed to verify the experimental results, and the modal and FEA analyses produced very similar results. The study concludes that future research should investigate the effects of tool holders made from high alloy steel alloys on process damping. Overall, this paper provides important insights into the effects of tool holder materials on chatter vibration and process damping in turning operations, which can help in the design of more efficient and effective cutting systems.
- 1 November 2021
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 43 (11) , 1-14
Process damping model approach in milling operations
- 1 November 2021
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 43 (11) , 1-14
Process damping model approach in milling operations