Grigorij Muliuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Grigorij Muliuk has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Jose Trindade
X-Celeprint Ltd., Cork, Ireland
2 shared publications - Dries Van Thourhout
Ghent University - IMEC
2 shared publications Gunther Roelkens
Ghent University-IMEC
2 shared publications- Gunther Roelkens
Photonics Research Group, Department of Information Technology, Ghent University imec, Ghent, Belgium
2 shared publications Guy Lepage
IMEC
2 shared publicationsJing Zhang
Ghent University-IMEC
2 shared publications
Latest Publications
- 18 May 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (11) , 19467-19477
High-performance thermally-robust C-band GeSi FK electro-absorption modulators on 300-mm silicon photonics platform
We demonstrate a high-performance, thermally-robust, C-band GeSi Franz-Keldysh electro-absorption modulator (FK-EAM) featuring a compact 0.5 x 50 μ m 2 active region on a 300-mm silicon photonics platform. The static electrical and optical performance is experimentally evaluated over wide operating ranges, with wafer-scale results yielding an extinction ratio (ER) of 6.44 ± 0.38 dB and a transmitter penalty (TP) of 9.25 ± 0.15 dB, while the best dies achieve an insertion loss (IL) of ∼ 5 dB, figure-of-merit (FOM = ER/IL) of 1.23, and TP of 8.8 dB at λ = 1550 nm under a 2 V peak-to-peak drive, representing the best reported EAM performance. The temperature-dependent measurements from 25–85 ∘ C show a monotonic red-shift rate of 0.8 nm/ ∘ C, while maintaining stable performance with ER > 6 dB, FOM > 1, and TP ∼ 9-10 dB across the wafer, demonstrating temperature-robust modulation performance comparable to state-of-the-art room-temperature EAMs. Furthermore, robust EAM operation beyond the nominal design window (∼1590 nm) is sustained even at 85 ∘ C. These results establish GeSi EAMs as a key enabling technology for high-speed, low-power, dense silicon-photonic transceivers, operating reliably in thermally exposed dynamic environments, paving the way for next-generation optical I/O applications.
- 18 May 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (11) , 19467-19477
High-performance thermally-robust C-band GeSi FK electro-absorption modulators on 300-mm silicon photonics platform
We demonstrate a high-performance, thermally-robust, C-band GeSi Franz-Keldysh electro-absorption modulator (FK-EAM) featuring a compact 0.5 x 50 μ m 2 active region on a 300-mm silicon photonics platform. The static electrical and optical performance is experimentally evaluated over wide operating ranges, with wafer-scale results yielding an extinction ratio (ER) of 6.44 ± 0.38 dB and a transmitter penalty (TP) of 9.25 ± 0.15 dB, while the best dies achieve an insertion loss (IL) of ∼ 5 dB, figure-of-merit (FOM = ER/IL) of 1.23, and TP of 8.8 dB at λ = 1550 nm under a 2 V peak-to-peak drive, representing the best reported EAM performance. The temperature-dependent measurements from 25–85 ∘ C show a monotonic red-shift rate of 0.8 nm/ ∘ C, while maintaining stable performance with ER > 6 dB, FOM > 1, and TP ∼ 9-10 dB across the wafer, demonstrating temperature-robust modulation performance comparable to state-of-the-art room-temperature EAMs. Furthermore, robust EAM operation beyond the nominal design window (∼1590 nm) is sustained even at 85 ∘ C. These results establish GeSi EAMs as a key enabling technology for high-speed, low-power, dense silicon-photonic transceivers, operating reliably in thermally exposed dynamic environments, paving the way for next-generation optical I/O applications.
- 10 October 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (22) , 39329-39339
Micro-transfer-printed narrow-linewidth III-V-on-Si double laser structure with a combined 110 nm tuning range
In this work, we demonstrate for the first time a narrow-linewidth III-V-on-Si double laser structure with more than a 110 nm wavelength tuning range realized using micro-transfer printing (µTP) technology. Two types of pre-fabricated III-V semiconductor optical amplifiers (SOAs) with a photoluminescence (PL) peak around 1500 nm and 1550 nm are micro-transfer printed on two silicon laser cavities. The laser cavities are fabricated in imec’s silicon photonics (SiPh) pilot line on 200 mm silicon-on-insulator (SOI) wafers with a 400 nm thick silicon device layer. By combining the outputs of the two laser cavities on chip, wavelength tunability over S+C+L-bands is achieved.
- 10 October 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (22) , 39329-39339
Micro-transfer-printed narrow-linewidth III-V-on-Si double laser structure with a combined 110 nm tuning range
In this work, we demonstrate for the first time a narrow-linewidth III-V-on-Si double laser structure with more than a 110 nm wavelength tuning range realized using micro-transfer printing (µTP) technology. Two types of pre-fabricated III-V semiconductor optical amplifiers (SOAs) with a photoluminescence (PL) peak around 1500 nm and 1550 nm are micro-transfer printed on two silicon laser cavities. The laser cavities are fabricated in imec’s silicon photonics (SiPh) pilot line on 200 mm silicon-on-insulator (SOI) wafers with a 400 nm thick silicon device layer. By combining the outputs of the two laser cavities on chip, wavelength tunability over S+C+L-bands is achieved.
- 27 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (4) , 287-290
$4\times25$ Gbps Polarization Diversity Silicon Photonics Receiver With Transfer Printed III-V PhotodiodesWe demonstrate the transfer-printing-based integration of III-V substrate-illuminated p-i-n photodetectors onto a 4-wavelength-channel silicon photonics polarization diversity receiver circuit. 4×25 Gbps operation is demonstrated for 2.5-nm wavelength channel spacing in the C-band. Transfer printing is an enabling technology for massively parallel heterogeneous III-V-on-Si integration.
- 27 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (4) , 287-290
$4\times25$ Gbps Polarization Diversity Silicon Photonics Receiver With Transfer Printed III-V PhotodiodesWe demonstrate the transfer-printing-based integration of III-V substrate-illuminated p-i-n photodetectors onto a 4-wavelength-channel silicon photonics polarization diversity receiver circuit. 4×25 Gbps operation is demonstrated for 2.5-nm wavelength channel spacing in the C-band. Transfer printing is an enabling technology for massively parallel heterogeneous III-V-on-Si integration.
- 18 January 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (2) , 2023-2032
High-alignment-accuracy transfer printing of passive silicon waveguide structures
We demonstrate the transfer printing of passive silicon devices on a silicon-on-insulator target waveguide wafer. Adiabatic taper structures and directional coupler structures were designed for 1310 nm and 1600 nm wavelength coupling tolerant for ± 1 µm misalignment. The release of silicon devices from the silicon substrate was realized by underetching the buried oxide layer while protecting the back-end stack. Devices were successfully picked by a PDMS stamp, by breaking the tethers that kept the silicon coupons in place on the source substrate, and printed with high alignment accuracy on a silicon photonic target wafer. Coupling losses of −1.5 +/− 0.5 dB for the adiabatic taper at 1310 nm wavelength and −0.5 +/− 0.5 dB for the directional coupler at 1600 nm wavelength are obtained.
- 18 January 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (2) , 2023-2032
High-alignment-accuracy transfer printing of passive silicon waveguide structures
We demonstrate the transfer printing of passive silicon devices on a silicon-on-insulator target waveguide wafer. Adiabatic taper structures and directional coupler structures were designed for 1310 nm and 1600 nm wavelength coupling tolerant for ± 1 µm misalignment. The release of silicon devices from the silicon substrate was realized by underetching the buried oxide layer while protecting the back-end stack. Devices were successfully picked by a PDMS stamp, by breaking the tethers that kept the silicon coupons in place on the source substrate, and printed with high alignment accuracy on a silicon photonic target wafer. Coupling losses of −1.5 +/− 0.5 dB for the adiabatic taper at 1310 nm wavelength and −0.5 +/− 0.5 dB for the directional coupler at 1600 nm wavelength are obtained.
- 24 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (5) , 1249-1254
Transfer Print Integration of Waveguide-Coupled Germanium Photodiodes Onto Passive Silicon Photonic ICs
We demonstrate the integration of waveguide-coupled germanium photodiodes onto passive silicon waveguide circuits by means of transfer printing. This involves the release of the photodiodes from the silicon-on-insulator source wafer by underetching the buried oxide layer, while at the same time protecting the back-end stack. Tethers were formed to keep the released photodiode coupons in place. Coupons were then transfer printed to a silicon photonic target wafer with an alignment accuracy better than $\pm$1 micrometer. 0.66 A/W waveguide-referred photodiode responsivity at 1550 nm was obtained. High speed measurements yielded open eye diagrams at 40 Gbit/s.
- 24 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (5) , 1249-1254
Transfer Print Integration of Waveguide-Coupled Germanium Photodiodes Onto Passive Silicon Photonic ICs
We demonstrate the integration of waveguide-coupled germanium photodiodes onto passive silicon waveguide circuits by means of transfer printing. This involves the release of the photodiodes from the silicon-on-insulator source wafer by underetching the buried oxide layer, while at the same time protecting the back-end stack. Tethers were formed to keep the released photodiode coupons in place. Coupons were then transfer printed to a silicon photonic target wafer with an alignment accuracy better than $\pm$1 micrometer. 0.66 A/W waveguide-referred photodiode responsivity at 1550 nm was obtained. High speed measurements yielded open eye diagrams at 40 Gbit/s.
- 25 May 2016
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 47 (1) , 1764-1767
P‐172: Temperature Distribution in WRGB AMOLED Displays
This paper explains how a non‐uniform temperature distribution arises across an OLED display and how it is influenced by the image content. IR camera measurements on a sample 55” WRGB OLED display and a thermal model that allows simulating the temperature distribution across an OLED display are presented. It has been shown before that temperature has a direct impact on the picture quality of an OLED display. Therefore, a good understanding of the thermal behavior of an OLED display is important. The presented thermal model can be a useful tool in the design phase of an OLED display.
- 25 May 2016
- Published by Wiley in SID Symposium Digest of Technical Papers
- Vol. 47 (1) , 1764-1767
P‐172: Temperature Distribution in WRGB AMOLED Displays
This paper explains how a non‐uniform temperature distribution arises across an OLED display and how it is influenced by the image content. IR camera measurements on a sample 55” WRGB OLED display and a thermal model that allows simulating the temperature distribution across an OLED display are presented. It has been shown before that temperature has a direct impact on the picture quality of an OLED display. Therefore, a good understanding of the thermal behavior of an OLED display is important. The presented thermal model can be a useful tool in the design phase of an OLED display.