LLLoong Kong Leong

Loong Kong Leong

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Loong Kong Leong has a total of 37 co-authors. Here are the top co-authors by number of shared publications:

  • Yeow Hong Yap

    Department of Chemical Engineering, Lee Kong Chian Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Bandar Sungai Long, Kajang 43000, Selangor, Malaysia

    3 shared publications
  • Sumathi Sethupathi

    Faculty of Engineering and Green Technology Universiti Tunku Abdul Rahman Kampar Perak Malaysia

    2 shared publications
  • Sumathi Sethupathi

    Universiti Tunku Abdul Rahman

    2 shared publications
  • Abdul Rahman Mohamed

    School of Chemical Engineering, Universiti Sains Malaysia, Engineering Campus, Pulau Pinang, Malaysia

    1 shared publication
  • Chai Hoon Koo

    Universiti Tunku Abdul Rahman

    1 shared publication
  • Chiang Chao-Lung

    Department of Chemical Engineering Department of Chemical Engineering Department of Chemical Engineering and Materials Science/Environmental Technology Research Center Department of Chemical Engineering and Materials Science/Environmental Technology Research Center Department of Chemical Engineering Universiti Tunku Abdul Rahman Malaysia Universiti Tunku Abdul Rahman Malaysia Yuan Ze University Taiwan Yuan Ze University Taiwan Universiti Tunku Abdul Rahman Malaysia

    1 shared publication

Latest Publications

  • Open Access

    Solventless Glycerol Etherification to Di- and Tri-Glycerol over Mg-La Mixed Oxides Derived from Layered Double Hydroxides

    by Prakas Palanychamy, Steven Lim, Yap Yeow Hong, Leong Loong Kong, Sujan Chowdhury

    Mg–La mixed metal oxides derived from layered double hydroxide (LDH) precursors were synthesized via coprecipitation and evaluated as heterogeneous catalysts for solventless glycerol etherification to short-chain polyglycerols. The influence of Mg/La molar ratio on the structural, textural, and catalytic properties of the catalysts was systematically investigated using XRD, BET, SEM-EDX, FTIR, TPD-CO2, TPD-NH3 and ICP-OES analyses. XRD confirmed the formation of La2O2CO3 phases, while CO2-TPD analysis revealed the presence of abundant medium-to-strong basic sites. Among the synthesized catalysts, Mg0.25La0.75O2 exhibited the highest basic site concentration (6830 µmol g−1) and superior catalytic performance due to the possible cooperative interaction between Mg- and La-derived sites. Under optimum reaction conditions of 220 °C, 8 h, and 2 wt% catalyst loading, the catalyst achieved 90% glycerol conversion with 70% diglycerol selectivity, 23% triglycerol selectivity, and 84% combined diglycerol and triglycerol yield. Reaction temperature, catalyst loading, and reaction duration significantly influenced oligomer distribution and catalyst performance. Reusability studies demonstrated acceptable catalyst stability for up to four cycles before gradual deactivation caused by oligomer deposition and metal leaching. The results highlight Mg–La mixed oxides as promising catalysts for sustainable solvent-free glycerol valorization, while demonstrating a scalable and environmentally benign strategy for maximizing lower-degree polyglycerol production within shorter reaction durations and reduced processing cost.

  • Open Access

    Use of Direct Microwave Irradiation in the Synthesis of Vanadium Phosphorus Oxide Catalysts via Vanadyl Hydrogen Phosphate Sesquihydrate Precursor

    by Jo Yee Kang, Loong Kong Leong, Yeow Hong Yap, Thian Khok Yong

    Four vanadyl pyrophosphate (VPO) catalysts were prepared via the sesquihydrate precursor route using direct microwave irradiation and reflux synthesis methods. The synthesis of the sesquihydrate precursor was carried out in 2 stages. The synthesized catalysts were denoted as VPOs-DD, VPOs-RR, VPOs-RD, and VPOs-DR; where VPOs represented VPO catalysts produced through sesquihydrate precursor, and D and R represented direct microwave irradiation and reflux synthesis methods, respectively. The direct microwave irradiation synthesis method was found to reduce the synthesis duration significantly for both stages of the precursor synthesis, from 48 to 4 h. An exclusive secondary configuration, akin to a needle-shaped form in chrysanthemums, is specifically noted in VPOs-DD could increase the specific surface area by 35.4% compared to the bulkier structure of VPOs catalyst produced via the conventional reflux synthesis method (VPOs-RR). Direct microwave irradiation could induce the removal of more than 4 times the total amount of oxygen atoms from the lattice of V4+ and V5+ phases, as compared to the conventional reflux method counterpart. This ultimately produced VPOs catalysts with greater catalytic performances and TON. In summary, employing direct microwave irradiation could generate VPOs catalysts with increased efficiency, improved activity and selectivity as compared to the conventional reflux method.

  • Open Access

    Carbon capture from low CO2 concentration stream through ternary alkali metal nitrates promotion of MgO sorbents at intermediate temperature and low space velocity

    by Kian Hoong Chai, Loong Kong Leong, Sumathi Sethupathi, Kok Chung Chong, Thomas Chung-Kuang Yang, Sze Pheng Ong, Yeow Hong Yap


  • Effect of CO2 adsorbents on the Ni‐based dual‐function materials for CO2 capturing and in situ methanation

    by Kian Hoong Chai, Loong Kong Leong, David Shan‐Hill Wong, De‐Hao Tsai, Sumathi Sethupathi

    The present work studied the effect of different carbon dioxide (CO2) adsorbents on Ni‐based dual‐function materials (DFMs) for the development of carbon capture and on‐site utilization in a reactor at isothermal condition. The DFMs containing Ni functioning as a methanation catalyst with various CO2 adsorbents (i.e., CaO, MgO, K2CO3, or Na2CO3) were prepared on γ‐Al2O3 through sequential impregnation. The result indicated that Ni‐Na2CO3/γ‐Al2O3 had the highest methanation capacity (i.e., 0.1783 mmol/g) and efficiency (i.e., 71.09%) in the CO2 adsorption–methanation test. The CO2 uptake and the subsequent methanation capacity of the Ni‐Na2CO3/γ‐Al2O3 increased to more than 24 times and more than 17 times, respectively, compared to Ni/γ‐Al2O3. The high methanation capacity was correlated to its highest amount of weak basic sites, substantial CO2 capture capacity and capture/release efficiency, and reactivity to H2 at a lower temperature, supported by CO2‐TPD, TGA analyses for adsorption or adsorption–desorption at the isothermal condition, and H2‐TPRea, respectively. A continuous cyclic CO2 adsorption–methanation was performed by using the Ni‐Na2CO3/γ‐Al2O3 and Ni‐CaO/γ‐Al2O3, showing that the CO2 adsorption capacity was stabilized from third cycle onward, whereas the methanation capacity was stabilized at all cycles, indicating the high stability of the DFMs for both CO2 adsorption and subsequent methanation. This work demonstrated successful synthesis of the Ni‐based, low‐cost, and stable DFMs with the ability to produce methane via the direct capture of CO2.


  • Open Access

    Preparation of Metal Organic Framework (MOF) Derived Bimetallic Catalyst for Dry Reforming of Methane

    by Kah Chun Chin, Loong Kong Leong, Shih-Yuan Lu, De-Hao Tsai, Sumathi Sethupathi

    In the past decade, efforts have been focused on development of catalyst to show high activity for dry reforming of methane (DRM). The development of catalyst has been crucial to be carried out as this may significantly reduce the concentration of most common greenhouse gases, namely methane (CH4) and carbon dioxide (CO2) in the atmosphere. In present work, a series of varying molar ratio of Ni:Ce metal organic framework (MOF) derived catalysts were grown on alumina in one step. The synthesis steps were in accordance to reported solvothermal method for the syntheses of NH2-MIL-88B with slight modification. This was followed by reduction at 500°C in hydrogen environment for 1 h. The physical and chemical properties of the catalysts were probed by powder XRD, BET surface area analysis, EDX, ICP, CO2-TPD and H2-TPR. XRD showed that diffraction patterns were in agreement with the diffraction pattern of MOF synthesized in previous work, thus confirmed the successful formation of the MOF structure. The variation in the molar ratio of Ni:Ce did not show significant difference in the diffraction pattern of the MOF-derived catalysts. For reduction phase, sharp diffraction peaks were detected at 2? = 44.5°, 51.85°, and 76.37°, which can be indexed to (1 1 1), (2 0 0) and (2 2 0) planes of face-centered cubic (FCC) metallic Ni, respectively. The addition of Ce promoted smaller particle size of Ni, ranging from 4.6 nm to 6.88 nm. The presence of CeO2 was observed at 2? = 28.6°, 33.0°, and 56.4°. Elemental distribution was compared between EDX and ICP-OES. ICP-OES and EDX analyses indicated that weight percent of bimetallic metal of Ni and Ce was consistent, in which the amount of respective metal obeyed the ratio trend of the metal precursors added during the MOF synthesis. This suggested the homogeneity of the catalyst, even though EDX showed relatively higher weight percent than ICP-OES. The catalytic performance of catalysts showed that 1Ni1Ce exhibited better conversion of CH4 and CO2, with 63.5% and 86.8% respectively at 800oC, and the conversion tend to increase at a higher temperature. The results were convincing for the design of a performing catalyst for DRM process.


  • Effect of direct ultrasound synthesis via a sesquihydrate route on bismuth‐promoted vanadyl pyrophosphate catalysts

    by Kang‐Zhi Goo, Yeow‐Hong Yap, Kuen‐Song Lin, Loong‐Kong Leong

    A series of 1, 3, and 5% Bi‐doped vanadium phosphate catalyst catalysts were prepared via sesquihydrate route using direct ultrasound method and were denoted as VPSB1, VPSB3, and VPSB5, respectively. These catalysts were synthesized solely using a direct ultrasound technique and calcined in a n‐butane/air mixture. This study showed that catalyst synthesis time can be drastically reduced to only 2 hr compared to conventional 32–48 hr. All Bi‐doped catalysts exhibited a well‐crystallized (VO)2P2O7 phase. In addition, two V5+ phases, that is, β‐VOPO4 and αII‐VOPO4, were observed leading to an increase in the average oxidation state of vanadium. All catalysts showed V2p3/2 at approx. 517 eV, giving the vanadium oxidation state at approx. 4.3–4.6. Field‐emission scanning electron microscopy micrographs showed the secondary structure consisting of thin and small plate‐like crystal clusters due to the cavitation effect of ultrasound waves. VPSB5 showed the highest amount of oxygen species removed associated with the V5+ and V4+ species in temperature‐programmed reduction in H2 analyses. TheX‐ray absorption near edge structure (XANES) measurement showed the occurrence of vanadium oxide reductions in hydrogen gas flow, indicating the presence of V4+ and V5+ species. Higher average valence states of V5+, indicating more V5+ phases, were present. The addition of bismuth has increased the activity and selectivity to maleic anhydride.


  • Open Access

    Direct ultrasound synthesis of vanadyl pyrophosphate catalyst for partial oxidation of n-butane to maleic anhydride

    by Silver Goo, Loong Kong Leong, Yap Yeow Hong, Lin Kuen-Song, Chiang Chao-Lung

    Three VPO catalyst were prepared via direct ultrasound technique using organic, sesquihydrate and dihydrate routes, denoted as VPOuo, VPOus and VPOud respectively. These catalysts were synthesised solely on direct ultrasound technique and calcined in n-butane/air mixture. All catalysts exhibited well-crystallised (VO)2P2O7 phase. VPOus and VPOud showed αII-VOPO4, which led to an increase in average oxidation state of vanadium. All catalysts were showing O1s approx. 530 eV, similar P2p value and V2p3/2 at approx. 517 eV, giving vanadium oxidation state of approx. 4.0 – 4.2. FE-SEM micrographs showed the secondary structure consisting of thin plate-like crystals in different sizes agglomerate to each other due to cavitation effect. HR-TEM demonstrated the existence of polycrystalline phase. The nature of the oxidants was investigated by TPR in H2. VPOus showed highest amount of total removal of oxygen species suggesting that it had highest activity compared to VPOuo and VPOud. The XANES measurement of these catalysts showed the occurrence of vanadium oxide reductions in flowing hydrogen gas, which indicates the presence of V4+ and V5+ species. Catalytic tests demonstrated that the activity and selectivity to maleic anhydride increased with direct ultrasound technique. This study showed that catalyst synthesis time can be reduced to only 2 hours and giving polycrystalline particles compared to conventional method.

  • Role of ZnO in Ni/ZnO/Al2O3 as catalytic materials for hydrogenation of vegetable oil

    by Farng Hui Wong, Timm Joyce Tiong, Loong Kong Leong, Yeow Hong Yap

    The potential of porous Ni/ZnO/Al2O3 as a better material for hydrogenation of vegetable oil was studied and compared to Ni/Al2O3 catalyst. Ni/ZnO/Al2O3 and Ni/Al2O3 catalysts were synthesized with co-precipitation method and characterized with ICP-OES, EDXS, XPS, XRD and N2 adsorption-desorption analyses. Performance of the catalysts was assessed in partial hydrogenation of sunflower oil. The formation of crystalline Ni, NiO and ZnO phases from a uniform hydrotalcite phase was clearly detected in the XRD spectra which supports the change in chemistry involved during catalyst synthesis. Albeit having Ni content that is only half of Ni/Al2O3 catalyst, Ni/ZnO/Al2O3 achieved 23 % higher hydrogenation activity. This is attributed to the availability of larger pores (32.9 nm) in Ni/ZnO/Al2O3 which facilitates diffusion of bulky triglyceride molecules during hydrogenation. The incorporation of ZnO in conventional Ni/Al2O3 catalyst was shown to alter the material characteristics by increasing availability of large pores in the material due to ZnO migration, making it a potential alternative material to synthesize catalyst for partial hydrogenation of vegetable oil.


  • Open Access

    Effect of Filler Content on Transport Properties of Sulfonated Polyether Ether Ketone (SPEEK) Composite Proton Exchange Membranes

    by Min Yan Chia, Hui San Thiam, Loong Kong Leong, Chai Hoon Koo

    Proton exchange membrane for direct methanol fuel cell was developed by the incorporation of silicotungstic acid supported on silica (SiO2-SiWA) into SPEEK polymer. The properties of composite membranes with various silica/SiWA ratios were investigated and compared in this study. It was found that high silica to SiWA weight ratio (2:1) resulted in porous membrane with high proton conductivity and moderate methanol permeability. Reduction in the aforementioned ratio to 1:1 resulted in a more compact structure with better thermal stability, however, leaching of SiWA from the membrane occurred due to insufficient support. SPEEK membrane incorporated with 10 wt% SiO2 and 5 wt% SiWA showed the highest selectivity of 6.44 × 104 S.s/cm3 and performed better than that of the pure SPEEK membrane. These results suggested that these membranes have potential to be considered for DMFCs applications.


  • Physicochemical properties of marine collagen-alginate biomaterial

    by K. S. Soon, S. L. Hii, C. L. Wong, L. K. Leong, K. K. Woo

    Collagen base biomaterials are widely applied in the field of tissue engineering. However, these fibrous proteins in animal connective tissues are insufficient to fulfill the mechanical properties for such applications. Therefore, alginate as a natural polysaccharide was incorporated. In this study, Smooth wolf herring skins was collected from the local fish ball processing industry for collagen extraction using acid solubilisation method. On the other hand, alginate from brown seaweed (Sargassum polycystum) was extracted with calcium carbonate at 50 °C. The composite films of different collagen and alginate ratio were prepared by lyophilisation with pure collagen film as control. The effects of alginate on swelling behaviour, porosity, collagenase degradation and tensile strength of the composite films were investigated. Swelling behaviour increased with alginate content, 50 % alginate film achieved 1254.75 % swelling after 24 h. All composite films achieved more than 80 % porosity except the film with 80 % collagen (65.41 %). Porosity was highest in 100 % alginate (94.30 %). Highest tensile strength (1585.87 kPa) and young modulus (27.05 MPa) was found in 50 % alginate film. In addition, resistance to collagenase degradation was improved with alginate content, lowest degradation rate was determined in 80 % alginate film. Results indicated alginate is efficient in improving some mechanical properties of the composite film.