Yuki Tokumoto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yuki Tokumoto has a total of 140 co-authors. Here are the top co-authors by number of shared publications:
Ichiro Yonenaga
19 shared publicationsYutaka Ohno
16 shared publicationsI. Yonenaga
9 shared publicationsKeiichi Edagawa
Institute of Industrial Science, The University of Tokyo
9 shared publications- Keiichi Edagawa
Institute of Industrial Science, The University of Tokyo, Meguro, Tokyo 153-8505, Japan
9 shared publications Kentaro Kutsukake
Tohoku University 1 Institute for Materials Research Sendai 980-8577, Japan
9 shared publications
Latest Publications
- 17 July 2026
- Published by Elsevier in Journal of Crystal Growth
- Vol. 694
Edge facets and twins in highly impurity-doped Czochralski-Si: A question on twin generation in semiconductors
- 17 July 2026
- Published by Elsevier in Journal of Crystal Growth
- Vol. 694
Edge facets and twins in highly impurity-doped Czochralski-Si: A question on twin generation in semiconductors
- 15 June 2026
- Published by Physical Society of Japan in Journal of the Physical Society of Japan
- Vol. 95 (6)
Eliminating Nuclear Contributions in Low-Temperature Calorimetry Using the Initial Slope Method
- 15 June 2026
- Published by Physical Society of Japan in Journal of the Physical Society of Japan
- Vol. 95 (6)
Eliminating Nuclear Contributions in Low-Temperature Calorimetry Using the Initial Slope Method
- 5 June 2026
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 10 (6)
Unusual NMR signatures of superconductivity in the two-dimensional quasicrystal ( Ta 0.95 Cu 0.05 ) 1.6 Te
- 5 June 2026
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 10 (6)
Unusual NMR signatures of superconductivity in the two-dimensional quasicrystal ( Ta 0.95 Cu 0.05 ) 1.6 Te
- Open Access
- 1 May 2026
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 67 (5) , 664-668
Effect of the Third Element Addition in Ta–Te Dodecagonal Quasicrystal
The Ta–Te dodecagonal quasicrystal (dd-QC) is the only known van der Waals (vdW) layered quasicrystal and exhibits bulk superconductivity at ∼1 K. In this study, ternary and quaternary compounds were synthesized by adding a third element (X = Cu, In, Sb, Ag, Au, Ti, Nb) to the Ta–Te dd-QC system. Powder X-ray diffraction (XRD) revealed that single-phase dd-QCs were obtained for several compositions, with improved quasicrystallinity indicated by a reduced full width at half maximum (FWHM) of the quasiperiodic peaks. Electrical resistivity measurements demonstrated superconducting transitions at approximately 1 K, with Tc varying systematically depending on the added element. The Ta–Ti–Nb–Te quaternary system exhibited the highest Tc of 1.14 K. These results demonstrate that compositional modification effectively tunes both the structural and superconducting properties of vdW layered quasicrystals.
- 1 May 2026
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 67 (5) , 664-668
Open AccessEffect of the Third Element Addition in Ta–Te Dodecagonal Quasicrystal
The Ta–Te dodecagonal quasicrystal (dd-QC) is the only known van der Waals (vdW) layered quasicrystal and exhibits bulk superconductivity at ∼1 K. In this study, ternary and quaternary compounds were synthesized by adding a third element (X = Cu, In, Sb, Ag, Au, Ti, Nb) to the Ta–Te dd-QC system. Powder X-ray diffraction (XRD) revealed that single-phase dd-QCs were obtained for several compositions, with improved quasicrystallinity indicated by a reduced full width at half maximum (FWHM) of the quasiperiodic peaks. Electrical resistivity measurements demonstrated superconducting transitions at approximately 1 K, with Tc varying systematically depending on the added element. The Ta–Ti–Nb–Te quaternary system exhibited the highest Tc of 1.14 K. These results demonstrate that compositional modification effectively tunes both the structural and superconducting properties of vdW layered quasicrystals.
- Open Access
- 21 April 2026
- Published by Elsevier in SSRN Electronic Journal
Edge facets in highly impurity-doped Czochralski-Si: Recall twin generation in semiconductors
We studied edge facets that developed at the outer periphery of highly impurity-doped, Czochralski (CZ)-grown silicon (Si) crystals in terms of defect generation. Some characteristics of the edge facets were identified. {111} facets were detected within the growth ridges of [001]-oriented, antimony-, arsenic-, and phosphorus-doped crystals. The impurity concentrations in the edge facets were higher than in the matrix. It is thought that the enhancement of their segregation coefficient originates from the fact that the edge facets initiate later and then grow faster along the facet plane than the rest of the crystal. The late growth and intensely fluctuating impurity concentration in the edge facets may result in structural defects at their boundaries. Twins were generated at the edge facets in impurity-doped CZ-Si. Additionally, de-twinning was observed at a position off an edge facet in the twin, suggesting that the conditions for twin generation need to be reconsidered.
- 21 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEdge facets in highly impurity-doped Czochralski-Si: Recall twin generation in semiconductors
We studied edge facets that developed at the outer periphery of highly impurity-doped, Czochralski (CZ)-grown silicon (Si) crystals in terms of defect generation. Some characteristics of the edge facets were identified. {111} facets were detected within the growth ridges of [001]-oriented, antimony-, arsenic-, and phosphorus-doped crystals. The impurity concentrations in the edge facets were higher than in the matrix. It is thought that the enhancement of their segregation coefficient originates from the fact that the edge facets initiate later and then grow faster along the facet plane than the rest of the crystal. The late growth and intensely fluctuating impurity concentration in the edge facets may result in structural defects at their boundaries. Twins were generated at the edge facets in impurity-doped CZ-Si. Additionally, de-twinning was observed at a position off an edge facet in the twin, suggesting that the conditions for twin generation need to be reconsidered.
- Open Access
- 1 September 2024
- Published by IOP Publishing in Applied Physics Express
- Vol. 17 (9) , 093001
Large Rashba spin–orbit coupling in metallic SrTaO3 thin films
We fabricated conductive SrTaO3 epitaxial films on insulator substrates and measured the Rashba parameter using weak anti-localization analysis. The Rashba parameter, reaching up to 9.9 × 10−13 eVm, is the highest among metallic oxides and is comparable to the LaAlO3/SrTiO3 interface, which is widely used in Rashba effect studies. This indicates the potential for oxide-based spintronic devices. To use them as devices, it is important to investigate how film thickness affects the resistivity. Films ranging from 8.6 to 25 nm exhibited metallic conduction, but those thicker than 25 nm showed an unexpected increase in resistivity, suggesting instability of the meta-stable Ta4+ state.
- 1 September 2024
- Published by IOP Publishing in Applied Physics Express
- Vol. 17 (9) , 093001
Open AccessLarge Rashba spin–orbit coupling in metallic SrTaO3 thin films
We fabricated conductive SrTaO3 epitaxial films on insulator substrates and measured the Rashba parameter using weak anti-localization analysis. The Rashba parameter, reaching up to 9.9 × 10−13 eVm, is the highest among metallic oxides and is comparable to the LaAlO3/SrTiO3 interface, which is widely used in Rashba effect studies. This indicates the potential for oxide-based spintronic devices. To use them as devices, it is important to investigate how film thickness affects the resistivity. Films ranging from 8.6 to 25 nm exhibited metallic conduction, but those thicker than 25 nm showed an unexpected increase in resistivity, suggesting instability of the meta-stable Ta4+ state.
- 19 August 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (8)
Validity of the constant relaxation time approximation in topological insulator: Sn-BSTS a case study
Gate-voltage dependent quantum oscillations in topological insulator Sn0.02Bi1.08Sb0.9Te2S (Sn-BSTS) are analyzed on the basis of the Lifshitz−Kosevich theory. The angular dependence of the quantum oscillations and Landau-level fan diagram analysis show that the quantum oscillations originate from topological surface states with the Berry phase of π. Gate-voltage control allows precise control of the Fermi energy, and a very weak energy dependence of the relaxation time τ of the topological surface states is revealed. By a simple algebraic argument using the linear response theory, it is shown that the weak energy dependence of τ validates the constant relaxation time approximation [τE,T=τ0] in the calculation of the Seebeck coefficient S and zTel=σS2T/κel.
- 19 August 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (8)
Validity of the constant relaxation time approximation in topological insulator: Sn-BSTS a case study
Gate-voltage dependent quantum oscillations in topological insulator Sn0.02Bi1.08Sb0.9Te2S (Sn-BSTS) are analyzed on the basis of the Lifshitz−Kosevich theory. The angular dependence of the quantum oscillations and Landau-level fan diagram analysis show that the quantum oscillations originate from topological surface states with the Berry phase of π. Gate-voltage control allows precise control of the Fermi energy, and a very weak energy dependence of the relaxation time τ of the topological surface states is revealed. By a simple algebraic argument using the linear response theory, it is shown that the weak energy dependence of τ validates the constant relaxation time approximation [τE,T=τ0] in the calculation of the Seebeck coefficient S and zTel=σS2T/κel.
- Open Access
- 20 July 2024
- Published by Springer Nature in npj Quantum Materials
- Vol. 9 (1) , 1-6
Anomalous upper critical field in the quasicrystal superconductor Ta1.6Te
Superconductivity in quasicrystals poses a new challenge in condensed matter physics. We measured the resistance and ac magnetic susceptibility of a Ta1.6Te dodecagonal quasicrystal, which is superconducting belowTc ~ 1 K. We show that the upper critical field increases linearly with a large slope of − 4.4 T/K with decreasing temperature down to 0.04 K, with no tendency to level off. The extrapolated zero-temperature critical field exceeds the Pauli limit by a factor of 2.3. We also observed flux-flow resistance with thermally activated behavior and an irreversibility field that is distinct from the upper critical field. We discuss these peculiarities in terms of the nonuniform superconducting gap and spin-orbit interaction in quasicrystal structures.
- 20 July 2024
- Published by Springer Nature in npj Quantum Materials
- Vol. 9 (1) , 1-6
Open AccessAnomalous upper critical field in the quasicrystal superconductor Ta1.6Te
Superconductivity in quasicrystals poses a new challenge in condensed matter physics. We measured the resistance and ac magnetic susceptibility of a Ta1.6Te dodecagonal quasicrystal, which is superconducting belowTc ~ 1 K. We show that the upper critical field increases linearly with a large slope of − 4.4 T/K with decreasing temperature down to 0.04 K, with no tendency to level off. The extrapolated zero-temperature critical field exceeds the Pauli limit by a factor of 2.3. We also observed flux-flow resistance with thermally activated behavior and an irreversibility field that is distinct from the upper critical field. We discuss these peculiarities in terms of the nonuniform superconducting gap and spin-orbit interaction in quasicrystal structures.
- 1 March 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (3) , 030906
Pioneering preparation and analysis of a clean surface on a microcrystal, mined by a focused ion beam
We demonstrate a series of procedures to prepare a clean surface of micro-sized graphite, mined from a bulk flake and securely affixed onto a macroscopic Si plate by focused ion beam scanning electron microscope. Analyses of structure and electronic (chemical) states were made using micro-beam X-ray photoelectron spectroscopy and angle-resolved photoemission spectroscopy. At the surface of the micro graphite, the band dispersion from a single-domain structure was observed. The proposed methodology showcases its capability to produce clean and high-quality micro samples suitable for surface-sensitive analyses. This technique paves the way to investigate surfaces of unexplored microcrystals embedded in complex materials.
- 1 March 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (3) , 030906
Pioneering preparation and analysis of a clean surface on a microcrystal, mined by a focused ion beam
We demonstrate a series of procedures to prepare a clean surface of micro-sized graphite, mined from a bulk flake and securely affixed onto a macroscopic Si plate by focused ion beam scanning electron microscope. Analyses of structure and electronic (chemical) states were made using micro-beam X-ray photoelectron spectroscopy and angle-resolved photoemission spectroscopy. At the surface of the micro graphite, the band dispersion from a single-domain structure was observed. The proposed methodology showcases its capability to produce clean and high-quality micro samples suitable for surface-sensitive analyses. This technique paves the way to investigate surfaces of unexplored microcrystals embedded in complex materials.
- Open Access
- 1 March 2024
- Published by Springer Nature in Nature Communications
- Vol. 15 (1) , 1-7
Superconductivity in a van der Waals layered quasicrystal
Van der Waals layered transition-metal chalcogenides are drawing significant attention owing to their intriguing physical properties. This group of materials consists of abundant members with various elements, having a variety of different structures. However, they are all crystalline materials, and the physical properties of van der Waals layered quasicrystals have never been studied to date. Here, we report on the discovery of superconductivity in a van der Waals layered quasicrystal of Ta1.6Te. The electrical resistivity, magnetic susceptibility, and specific heat of the quasicrystal unambiguously validate the occurrence of bulk superconductivity at a transition temperature of ~1 K. This discovery can promote new research on assessing the physical properties of novel van der Waals layered quasicrystals as well as two-dimensional quasicrystals; moreover, it paves the way toward new frontiers of superconductivity in thermodynamically stable quasicrystals.
- 1 March 2024
- Published by Springer Nature in Nature Communications
- Vol. 15 (1) , 1-7
Open AccessSuperconductivity in a van der Waals layered quasicrystal
Van der Waals layered transition-metal chalcogenides are drawing significant attention owing to their intriguing physical properties. This group of materials consists of abundant members with various elements, having a variety of different structures. However, they are all crystalline materials, and the physical properties of van der Waals layered quasicrystals have never been studied to date. Here, we report on the discovery of superconductivity in a van der Waals layered quasicrystal of Ta1.6Te. The electrical resistivity, magnetic susceptibility, and specific heat of the quasicrystal unambiguously validate the occurrence of bulk superconductivity at a transition temperature of ~1 K. This discovery can promote new research on assessing the physical properties of novel van der Waals layered quasicrystals as well as two-dimensional quasicrystals; moreover, it paves the way toward new frontiers of superconductivity in thermodynamically stable quasicrystals.