MHManuel Hildebrandt

Manuel Hildebrandt

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Manuel Hildebrandt has a total of 2 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Analysis of Heat Flux Distribution during Brush Seal Rubbing Using CFD with Porous Media Approach

    by Manuel Hildebrandt, Corina Schwitzke, Hans-Jörg Bauer

    This paper discusses the question of heat flux distribution between bristle package and rotor during a rubbing event. A three-dimensional Computational Fluid Dynamics (3D CFD) model of the brush seal test rig installed at the Institute of Thermal Turbomachinery (ITS) was created. The bristle package is modelled as a porous medium with local non-thermal equilibrium. The model is used to numerically recalculate experimentally conducted rub tests on the ITS test rig. The experimentally determined total frictional power loss serves as an input parameter to the numerical calculation. By means of statistical evaluation methods, the ma in influences on the heat flux distribution and the maximum temperature in the frictional contact are determined. The heat conductivity of the rotor material, the heat transfer coefficients at the bristles and the rubbing surface were identified as the dominant factors.


  • Open Access

    Contamination of Brush Seals by Oil and Salt and Its Impact on Rubbing and Hysteresis Behaviour

    by Manuel Hildebrandt, Corina Schwitzke, Hans-Jörg Bauer

    The literature already contains some experimental, analytical and numerical investigations on the rubbing and hysteresis behaviour of brush seals. What the investigations have in common is that they were carried out with new and uncontaminated seals, or that such a condition was assumed. The influence of contamination has not been explicitly investigated yet. Particularly in stationary gas and steam turbines, foreign substances can accumulate on and in the bristle package during steady-state operation. In the case of a rubbing event with a contaminated brush seal, e.g., during shutdown of the machine, the process is not expected to be comparable to that assumed in the presence of a new, uncontaminated seal. The present paper is dedicated to the question of the influence of contamination on the total frictional power loss generated during rubbing and the distribution of heat fluxes in friction contact. For this purpose, rub tests with two seals were carried out on the brush seal test rig of the Institute of Thermal Turbomachinery (ITS) in new conditions. Subsequently, the sealing packages were contaminated with oil or a salt mixture. After the treatment, the rub tests were repeated and compared with the previous tests. In addition, stiffness measurements were used to assess the degree of contamination. A strong influence on the rubbing behaviour by the contamination was detected. Contamination causes the flexibility of the bristle package to be greatly reduced. As a result, especially at the beginning of the first measurements, the total power losses and rotor heat inputs are strongly increased. This flexibility is partly regained in the course of the measurements. As expected, contamination also influences the hysteresis behaviour of the seal. A highly increased leakage rate after rubbing could be observed, because the bristles remained close to their deflected positions. In the case of the salted seal, however, an improvement in the leakage performance could be observed after several repeat tests.


  • Experimental Investigation on the Influence of Geometrical Parameters on the Frictional Heat Input and Leakage Performance of Brush Seals

    by Manuel Hildebrandt, Corina Schwitzke, Hans-Jörg Bauer

    Because of the superior sealing characteristics compared to labyrinth seals, brush seals found an increased spread in turbomachinery in recent years. Their outstanding sealing performance results mainly from their flexibility. Thus, a very small gap between the rotor and bristle package can be obtained without running the risk of severe detrimental deterioration in case of rubbing. Rubbing between rotor and seal during operation might occur as a result of e.g., an unequal thermal expansion of the rotor and stator or a rotor elongation due to centrifugal forces or maneuver forces. Thanks to the flexible structure of the brush seal the contact forces during a rubbing event are reduced; however, the frictional heat input can still be considerable. Particularly, in aircraft engines with their thin and lightweight rotor structures, the permissible material stresses can easily be exceeded by an increased heat input and thus harm the engine's integrity. The geometry of the seal has a decisive influence on the resulting contact forces and consequently the heat input. The complex interactions between the geometric parameters of the seal and the heat input and leakage characteristics are not yet fully understood. This paper presents the investigation of the influence of the geometric parameters of a brush seal on the heat input into the rotor and the leakage behavior. Two seals with different packing densities were tested under relevant engine conditions with pressure differences ranging from 1 to 7 bar, relative surface speeds ranging from 30 to 180 m/s, and radial overlaps ranging from 0.1 to 0.4 mm. The transient temperature rise during the rub event was recorded with 24 thermocouples in close proximity to the rub contact embedded in the rotor structure. By comparing the temperature curves with the results of a thermal finite element (FE) analysis of the rotor the heat input into the rotor was calculated iteratively. It could be shown that the packing density has a decisive influence on the overall operating behavior of a brush seal. Furthermore, results for the heat flux distribution between seal and rotor are shown.