Abdollah Bagheri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Abdollah Bagheri has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Devin K. Harris
Univ. of Virginia
2 shared publications - Osman E. Ozbulut
Department of Civil and Environmental Engineering University of Virginia Charlottesville Virginia USA
2 shared publications Ali Zare Hosseinzadeh
School of Civil Engineering and Environmental Science, University of Oklahoma, Norman, Oklahoma, USA
1 shared publicationDevin K. Harris
Department of Civil and Environmental Engineering, University of Virginia, Charlottesville, Virginia, USA
1 shared publicationMohamad Alipour
Department of Civil and Environmental Engineering, University of Virginia, Charlottesville, Virginia, USA
1 shared publication- Mohamad Alipour
University of Illinois Urbana-Champaign
1 shared publication
Latest Publications
- 26 February 2019
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- Vol. 15 (6) , 754-770
A hybrid experimental-numerical approach for load rating of reinforced concrete bridges with insufficient structural properties
This article presents a non-destructive approach for load rating of reinforced concrete bridges without structural plans. The approach is found on a hybrid method, which employs vibration and live load testing coupled with numerical simulation and model updating techniques, to converge on estimate of unknown structural parameters. The material properties of bridge and the amount of reinforcing steel for calculating the bending capacity of a bridge are determined through model updating results and nondestructive approaches. The updated model is then employed to determine load effects for calculating load rating factors, and these results are combined with live load test result to arrive at the bridge capacity, and ultimately the load rating. The method is validated by testing a skewed reinforced concrete slab bridge for load rating purposes. The bridge was instrumented with accelerometers and strain gages, and the responses of the bridge under vibration and quasi-static tests were measured. Results demonstrated that the proposed method is capable of determining the bridge capacity and load rating factor with good accuracy, and not only can be used for load rating of concrete bridges without structural information, but also can be useful in condition assessment of existing concrete bridge with available as-built information.
- 26 February 2019
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- Vol. 15 (6) , 754-770
A hybrid experimental-numerical approach for load rating of reinforced concrete bridges with insufficient structural properties
This article presents a non-destructive approach for load rating of reinforced concrete bridges without structural plans. The approach is found on a hybrid method, which employs vibration and live load testing coupled with numerical simulation and model updating techniques, to converge on estimate of unknown structural parameters. The material properties of bridge and the amount of reinforcing steel for calculating the bending capacity of a bridge are determined through model updating results and nondestructive approaches. The updated model is then employed to determine load effects for calculating load rating factors, and these results are combined with live load test result to arrive at the bridge capacity, and ultimately the load rating. The method is validated by testing a skewed reinforced concrete slab bridge for load rating purposes. The bridge was instrumented with accelerometers and strain gages, and the responses of the bridge under vibration and quasi-static tests were measured. Results demonstrated that the proposed method is capable of determining the bridge capacity and load rating factor with good accuracy, and not only can be used for load rating of concrete bridges without structural information, but also can be useful in condition assessment of existing concrete bridge with available as-built information.
- 1 August 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 144 (8)
Identification of Flexural Rigidity in Bridges with Limited Structural Information
This paper presents a method for identifying the flexural rigidity of bridges with limited structural information using modal frequencies identified from measured acceleration data. The output of this study provides a simple approach that can be adapted for condition assessment, the bridge load rating process, and nondestructive evaluation. The overall methodology is generic and can adapted for different types of bridge, but in this paper the approach is evaluated for skewed reinforced concrete slab bridges because the national database of bridges indicates that slab bridges represent the largest subset among bridge types. A large number of slab bridges with different structural dimensions, such as skew angle, span, width, and thickness, were first analyzed using the finite-element method to obtain their modal frequencies and their corresponding nondimensional frequency parameters, which play an important role in identifying the flexural rigidity of slab bridges. This population of generated data was then used to create an artificial intelligence model, which was developed to predict the nondimensional frequency parameters for slab bridges with different geometrical characteristics. Moreover, an algorithm based on variational mode decomposition was presented to identify the modal frequencies and damping ratio of a bridge. The method was first validated with a set of numerical studies, and it was then applied to a highly skewed reinforced concrete slab bridge in the Commonwealth of Virginia for load rating purposes. The bridge was instrumented with wireless accelerometers; the vibration responses of the bridge under ambient loading and impact hammer testing were recorded. Finally, the flexural rigidity of the bridge was identified from the established relationship between the modal frequencies and the flexural rigidity. Results show that the proposed method is capable of predicting flexural rigidity and can be used as a basis for the load rating of bridges without complete structural information.
- 1 August 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 144 (8)
Identification of Flexural Rigidity in Bridges with Limited Structural Information
This paper presents a method for identifying the flexural rigidity of bridges with limited structural information using modal frequencies identified from measured acceleration data. The output of this study provides a simple approach that can be adapted for condition assessment, the bridge load rating process, and nondestructive evaluation. The overall methodology is generic and can adapted for different types of bridge, but in this paper the approach is evaluated for skewed reinforced concrete slab bridges because the national database of bridges indicates that slab bridges represent the largest subset among bridge types. A large number of slab bridges with different structural dimensions, such as skew angle, span, width, and thickness, were first analyzed using the finite-element method to obtain their modal frequencies and their corresponding nondimensional frequency parameters, which play an important role in identifying the flexural rigidity of slab bridges. This population of generated data was then used to create an artificial intelligence model, which was developed to predict the nondimensional frequency parameters for slab bridges with different geometrical characteristics. Moreover, an algorithm based on variational mode decomposition was presented to identify the modal frequencies and damping ratio of a bridge. The method was first validated with a set of numerical studies, and it was then applied to a highly skewed reinforced concrete slab bridge in the Commonwealth of Virginia for load rating purposes. The bridge was instrumented with wireless accelerometers; the vibration responses of the bridge under ambient loading and impact hammer testing were recorded. Finally, the flexural rigidity of the bridge was identified from the established relationship between the modal frequencies and the flexural rigidity. Results show that the proposed method is capable of predicting flexural rigidity and can be used as a basis for the load rating of bridges without complete structural information.
- 17 April 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 56-63
Structural Monitoring and Damage Detection Using High-Speed Vibration Imaging
Current vibration based-structural health monitoring strategies have relied on vibration measurement methods using affixed accelerometers as a standard practice, but a fundamental limitation of this approach is that these sensors only provide point measurements. This low spatial resolution ultimately limits the effectiveness of structural monitoring and damage localization methods that rely on changes in global response to identify local damage features. To overcome these limitations, this paper focuses on the use of a high-speed imaging approach for measuring full-field vibration data for damage identification and localization in engineering structures. The framework is based on the design of a novel monitoring system that leverages a high-speed imaging system for capturing vibration response in a non-contact manner. A digital image processing algorithm is used to reconstruct full-field structural vibration response, which, in turn, enable modal properties of structures to be identified via a novel modal identification scheme. Processing the full-field modal data, the current state of the art in damage identification is extended to identify damages without in-place sensors. A series of experimental tests were performed on small-scale specimens to explore the potential of the proposed method. The preliminary study demonstrated the capability of the proposed approach to localize damage from non-contact and full-filed measurement.
- 17 April 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 56-63
Structural Monitoring and Damage Detection Using High-Speed Vibration Imaging
Current vibration based-structural health monitoring strategies have relied on vibration measurement methods using affixed accelerometers as a standard practice, but a fundamental limitation of this approach is that these sensors only provide point measurements. This low spatial resolution ultimately limits the effectiveness of structural monitoring and damage localization methods that rely on changes in global response to identify local damage features. To overcome these limitations, this paper focuses on the use of a high-speed imaging approach for measuring full-field vibration data for damage identification and localization in engineering structures. The framework is based on the design of a novel monitoring system that leverages a high-speed imaging system for capturing vibration response in a non-contact manner. A digital image processing algorithm is used to reconstruct full-field structural vibration response, which, in turn, enable modal properties of structures to be identified via a novel modal identification scheme. Processing the full-field modal data, the current state of the art in damage identification is extended to identify damages without in-place sensors. A series of experimental tests were performed on small-scale specimens to explore the potential of the proposed method. The preliminary study demonstrated the capability of the proposed approach to localize damage from non-contact and full-filed measurement.