EMEman Mohamed Mansour

Eman Mohamed Mansour

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Eman Mohamed Mansour has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A numerical and experimental approach to oil recovery performances during combined xanthan gum and carbon dioxide flooding

    by A. N. El-Hoshoudy, E. M. Mansour

    Carbon dioxide enhanced oil recovery (CO 2 -EOR) offers dual benefits of increasing hydrocarbon production and sequestering anthropogenic CO 2 ; however, conventional CO 2 flooding suffers from unfavorable mobility ratios and premature gas breakthrough, while polymer flooding alone faces challenges in high-salinity and high-temperature reservoirs. This study experimentally and numerically investigates the synergistic impact of combining xanthan gum polymer with CO 2 injection to maximize oil recovery. We conducted laboratory coreflood experiments on packed sandstone (porosity 22%, permeability 1000 mD) saturated with 31°API crude oil (6.0 cP at 70 °C), testing polymer concentrations of 1.0, 1.5, 2.0, and 2.5 g/L. We evaluated five flooding scenarios: water flooding (baseline), CO 2 flooding alone, polymer flooding alone, polymer (1.5 g/L) followed by CO 2 , and CO 2 followed by polymer (1.5 g/L). We then upscaled experimental findings using CMG-IMEX reservoir simulator to field scale. Water flooding recovered 70.0% of original oil in place (OOIP). CO 2 flooding alone increased recovery to 83.3% OOIP. Polymer flooding alone achieved maximum recovery of 81.3% OOIP at optimal concentration (1.5 g/L), while lower (1.0 g/L) and higher (2.5 g/L) concentrations yielded 79% and 73.5% OOIP, respectively. Sequential injection significantly outperformed single methods: polymer (1.5 g/L) followed by CO 2 achieved 89.3% OOIP, while CO 2 followed by polymer (1.5 g/L) achieved the highest recovery of 94.3% OOIP. An incremental gain of 24.3% over water flooding and 11.0% over CO 2 flooding alone. The combined polymer-CO 2 flooding system delivers superior oil recovery compared with individual processes. The optimal strategy-CO 2 injection followed by 1.5 g/L xanthan gum polymer-maximizes both microscopic displacement efficiency (CO 2 -driven oil swelling and viscosity reduction) and macroscopic sweep efficiency (polymer-driven mobility control). This hybrid approach represents a technically viable and economically promising EOR strategy for mature sandstone reservoirs while contributing to sustainable carbon management.


  • Open Access

    Neural network and regression approaches for predicting bubble point pressure in oil reservoirs

    by E. M. Mansour, Sayed Gomaa, A. N. El‑Hoshoudy

    Petroleum engineers must accurately determine bubble point pressure (Pb) to optimize oil field development from discovery to abandonment. Errors in predicting this parameter can lead to inaccurate reservoir and production estimates. To enhance Pb predictions, A total of experimentally measured 1,161 oil samples from Egyptian oil reservoirs (604 heavy oil and 557 light oil) were used for regression analysis. In contrast, 232 datasets were used to support the artificial neural network model. Existing correlations for Egyptian crude oils of varying oil gravity demonstrated moderate accuracy, highlighting the need for improved estimation methods tailored to local reservoir conditions. This study revises existing literature correlations, which previously related Pb to reservoir temperature, flashed gas specific gravity, gas-oil ratio, and stock tank oil API gravity. In contrast, this work develops two new correlation models: one tailored for heavy oils (15.3 < API < 34.9) and another for light oils (35.6 < API < 53.1), providing improved accuracy for these distinct oil types. These models incorporate a compositional approach, emphasizing fluid composition and physical parameters for enhanced precision. The equations were revised using multiple linear regression analysis, resulting in a statistical coefficient of 99.08% for heavy oils and 96.49% for light oils. Additionally, Artificial Neural Network (ANN) models were trained on a comprehensive dataset to develop highly accurate mathematical models for predicting bubble point pressure.


  • Open Access

    Synthesis and evaluation of amino acid ionic liquid for enhanced oil recovery: experimental and modeling simulation studies

    by E. M. Mansour, R. Hosny, Ammona S. Mohamed, Fatma M. Abdelhafiz

    Recovering the remaining oil after primary and secondary extraction methods poses a significant challenge. Enhanced oil recovery (EOR) techniques, which involve injecting fluids into reservoirs, aim to increase recovery rates. Ionic liquids, known for their adaptability, are emerging as promising agents in EOR, improving oil displacement by reshaping fluid properties and interacting with reservoir rocks. This study investigates the eco-friendly amino acid ionic liquid, AAIL [G0.5 C12][Pro], for EOR applications, focusing on its characterization and performance. Using pre-prepared quaternary ammonium salt PAMAM G0.5 C12 and proline, AAIL [G0.5 C12][Pro] was synthesized and confirmed via FTIR and 1H-NMR analyses. Rheological analysis identified 7 g of AAIL [G0.5 C12][Pro] as the optimal concentration for peak performance. Laboratory sand-pack displacement experiments demonstrated an 11% increase in oil recovery at this concentration. Further, a 3D reservoir model simulation validated the enhanced oil recovery potential of AAIL [G0.5 C12][Pro]. The study introduces the novel amino acid ionic liquid [G0.5 C12][Pro], which demonstrates superior effectiveness in enhancing oil recovery through significant wettability modification and interfacial tension reduction, underscoring its potential as an effective and environmentally friendly EOR agent compared to other ionic liquids and conventional methods.


  • Open Access

    Carbon Dioxide-Oil Minimum Miscibility Pressure Methods Overview

    by Eman Mohamed Ibrahim Mansour

    One of the essential parameters in carbon dioxide (CO2) miscible flooding is the minimum miscibility pressure (MMP). Minimum miscibility pressure (MMP) is defined as the lowest pressure at which recovery of oil is (90–92%) at injection (1.2 PV) of carbon dioxide (CO2). The injected gas and oil become a multi-contact miscible at a fixed temperature. Before any field trial, minimum miscibility pressure (MMP) must be determined. This parameter must be determined before any field trial because any engineer needs a suitable plan to develop an injection and surface facilities environment. Estimation of reliable (MMP) maybe by traditional laboratory techniques, but it is very costly and time-consuming. Also, it can rely on various literature (MMP) empirical correlations, but this is not a good strategy because each minimum miscibility pressure (MMP) correlation relates to a unique formation condition.


  • Open Access

    Enhanced Oil Recovery: Chemical Flooding

    by Ahmed Ragab, Eman M. Mansour

    The enhanced oil recovery phase of oil reservoirs production usually comes after the water/gas injection (secondary recovery) phase. The main objective of EOR application is to mobilize the remaining oil through enhancing the oil displacement and volumetric sweep efficiency. The oil displacement efficiency enhances by reducing the oil viscosity and/or by reducing the interfacial tension, while the volumetric sweep efficiency improves by developing a favorable mobility ratio between the displacing fluid and the remaining oil. It is important to identify remaining oil and the production mechanisms that are necessary to improve oil recovery prior to implementing an EOR phase. Chemical enhanced oil recovery is one of the major EOR methods that reduces the residual oil saturation by lowering water-oil interfacial tension (surfactant/alkaline) and increases the volumetric sweep efficiency by reducing the water-oil mobility ratio (polymer). In this chapter, the basic mechanisms of different chemical methods have been discussed including the interactions of different chemicals with the reservoir rocks and fluids. In addition, an up-to-date status of chemical flooding at the laboratory scale, pilot projects and field applications have been reported.


  • Hydrocarbon Simulation Behavior of Wet Natural Gas Reservoirs

    by Eman Mohamed Mansour, Mohamed El Aily

    Knowing hydrocarbon dew point conditions in natural gas (HCDP) are becoming widely important in the modern marketing of liquid and gas. Without determination dew point conditions (Pressure & Temperature), the accurate description of phase changes and phase behavior cannot be achieved. Numerous models for only predicting dew point pressure of gas condensate have been proposed and other for wet natural gas reservoirs, but there is no model for predicting both dew point pressure(DPp) and dew point temperature (DPT) for wet natural gas reservoirs. Some of the published models assume knowledge the reservoir fluid composition (requiring laboratory experiments to be performed), while others only require field parameters such as reservoir temperature, stock-tank oil API, and the condensate-gas ratio (CGR). The primary objectives of this paper is to determine dew point temperature (DPT) and dew point pressure (DPp) correlations using a fluid database of nearly fifty-six wet natural gas reservoirs, that is very important for engineers to understand and manage wet natural gas reservoirs. This model was made using multiple least-squares nonlinear regression analysis methods to find hydrocarbon dew point conditions (HCDP) as a function of [CGR, Tr, API gravity, gamma w, gamma C7+, MWw and C1, C2, CO2, N2 mole %] with a different constant value. Both statistical and graphical accuracy ensures that new models are more accurate in predicting hydrocarbon dew point conditions (HCDP) in comparison with equations of state by using limited data. Finally, thirty-four new separate set of measured data were used in testing models with an excellent agreement as compared with laboratory works.


  • Open Access

    Equation of State

    by Eman Mohamed Mansour

    An equation of state (EOS) is a thermodynamic expression that relates pressure (P), temperature (T), and volume (V). This equation is used to describe the state of reservoir fluids at given conditions. The cubic equations of state (CEOS) such as Van der Waals, Redlich-Kwong, Soave, and Peng-Robinson are simple models that have been widely used in the oil industry. This chapter expressed literature for EOS that varies from simple expressions to multiple constant and convoluted types of equations. Many attempts have been made to describe the thermodynamic behavior of fluids to predict their physical properties at given conditions. So, several forms of the equation of state have been presented to the oil industry in order to calculate reservoir fluid properties. The heat exchanger is important in wildly fields as in aerospace, petrochemical industry, refrigeration, and other fields. The optimization design of the heat exchanger is a great significance to industry process to reduce production cost, realize energy conservation, and reduce energy consumption.


  • Flashing Losses Emission Evaluation from Crude Oil Storage Tank

    by Eman Mohamed Mansour, Mohamed Elail, Saad Mohamed Desouky

    Evaporation is a natural phenomenon describing when a liquid turn into gas. Evaporation from roof storage tanks is a major source of product loss in the crude oil industry. A liquid will tend to evaporate depending on its vapor pressure. A liquid's vapor pressure is dependent on the surface temperature and composition of the liquid. Evaporation losses should be minimized to help maximize company revenue, meet regulatory requirements, and reduce greenhouse gas. This flashing loss is measured by carrying out the extensive experimental test. Therefore, this paper covers how to estimate oil flashing losses emissions factor (FLEF) percentage for crude oil storage tanks by using the new developed equation to minimize human errors. This statistical technique is a linear association between possible variables to assess flashing loss percentage as a function of operating temperature, sample point height (H1), oil tank height (H2), gas/oil ratio, gas gravity and oil gravity. A good result was obtained from the proposed equation as compared with popular equations by using graphical and statistical exactness. Lastly, modeling testing is ensuring excellent agreement with laboratory work by using new different samples.

  • Open Access

    Gases Reservoirs Fluid Phase Behavior

    by Eman Mohamed Mansour, Mohamed El Aily, Saad Eldin Mohamed Desouky

    This chapter discusses the fundamentals of the phase behavior of hydrocarbon fluids. Real reservoir fluids contain many more than two, three, or four components; therefore, phase-composition data can no longer be represented with two, three or four coordinates. Instead, phase diagrams that give more limited information are used. The behavior of reservoir of a reservoir fluid during producing is determined by the shape of its phase diagram and the position of its critical point. Many of producing characteristic of each type of fluid will be discussed. Ensuing chapters will address the physical properties of these three natural gas reservoir fluids, with emphasis on retrograde gas condensate gas, dry gas, and wet gas.


  • Improvement Wilson equation (K-Values) of gas-liquid equilibrium for Advancing Estimating Bubble Point Pressure

    by Eman Mohamed Mansour, Saad Mohamed Desouky

    Knowing the bubble point pressure of the oil reservoirs is a key factor for the petroleum engineers in order to optimize the development of the oil field starting from the discovery phase till the abandonment. Thus any considerable error in estimating the bubble point pressure will lead to errors in the production and reservoirs engineering calculations. More than six hundred Egyptian oil samples of PVT analysis were used to improve the Wilson equation (K-Values) for estimating bubble point pressure. None of the published bubble point pressure correlations is particularly accurate when applied to Egyptian crude oils. Experimental work was conducted in PVT- Services Center of Egyptian Petroleum Research Institute (EPRI). In this work, the K-values correlation proposed by Wilson equation was modified by adding new terms such as API, GOR, and heptanes plus-fraction (C7+) of compositional analysis of the reservoir fluid. Multiple non-linear regression analysis is used to calculate the new equation constant after adding the new terms. The statistical error analysis shows that the Correlation coefficient , the average percent relative error , the standard deviation and the average absolute percent relative error of the modifying are 99.75 %, 1.77%, 8.08%, and 6.84 %, respectively. This correlation of K-factor can be applied not only to low and moderate pressure but also to higher pressures up to (4500 psi) by this modification. Evaluation among the bubble point pressure calculated from the modified Wilson equation and the literature published ones were done. Results confirm that the modified Wilson equation is more accurate one and it can be used for estimating the reservoir fluids characteristics in the absence of data measurement.