Michal Sovcik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Michal Sovcik has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Daniel Arbet
Faculty of Electrical Engineering and Information Technology, Slovak University of Technology, Bratislava, Slovakia
6 shared publications - Viera Stopjakova
Department of IC Design and Test, Institute of Electronics and Photonics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology, Ilkovicova 3, 841 04 Bratislava, Slovakia
6 shared publications - Miroslav Potocny
Department of IC Design and Test, Institute of Electronics and Photonics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology, Ilkovicova 3, 841 04 Bratislava, Slovakia
5 shared publications - Martin Kovac
Institute of Electronics and Photonics , Faculty of Electrical Engineering and Information Technology , Slovak University of Technology , Bratislava , Slovakia
3 shared publications - Lukas Nagy
Department of IC Design and Test, Institute of Electronics and Photonics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology, Ilkovicova 3, 841 04 Bratislava, Slovakia
2 shared publications - David Maljar
Department of IC Design and Test, Institute of Electronics and Photonics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology, Ilkovicova 3, 841 04 Bratislava, Slovakia
1 shared publication
Latest Publications
- Open Access
- 11 November 2023
- Published by MDPI AG in Electronics
- Vol. 12 (22) , 4615
Digital Calibration of Input Offset Voltage and Its Implementation in FDDA Circuits
This article deals with the calibration method of analog integrated circuits (ICs) designed in CMOS nanotechnology. A brief analysis of various methods and techniques (e.g., fuse trimming, chopper stabilization, auto-zero technique, etc.) for calibration of a specific IC’s parameter is given, leading to motivation for this research that is focused on the digital calibration. Then, the principle and overall design of the calibration subcircuit, which was generally used to calibrate the input offset voltage of the operational amplifier (OPAMP). The essence of this work is verification of the proposed digital calibration algorithm for minimization the of a bulk-driven fully differential difference amplifier (FDDA) with the power supply voltage = 0.4 V. Evaluation of ASIC prototyped chip samples with silicon-proved results has been done. This evaluation contains comparison of selected parameters and characteristics obtained from both simulations and measurements of non-calibrated and calibrated FDDA configurations.- 11 November 2023
- Published by MDPI AG in Electronics
- Vol. 12 (22) , 4615
Open AccessDigital Calibration of Input Offset Voltage and Its Implementation in FDDA Circuits
This article deals with the calibration method of analog integrated circuits (ICs) designed in CMOS nanotechnology. A brief analysis of various methods and techniques (e.g., fuse trimming, chopper stabilization, auto-zero technique, etc.) for calibration of a specific IC’s parameter is given, leading to motivation for this research that is focused on the digital calibration. Then, the principle and overall design of the calibration subcircuit, which was generally used to calibrate the input offset voltage of the operational amplifier (OPAMP). The essence of this work is verification of the proposed digital calibration algorithm for minimization the of a bulk-driven fully differential difference amplifier (FDDA) with the power supply voltage = 0.4 V. Evaluation of ASIC prototyped chip samples with silicon-proved results has been done. This evaluation contains comparison of selected parameters and characteristics obtained from both simulations and measurements of non-calibrated and calibrated FDDA configurations. - Open Access
Low-Voltage DC-DC Converter for IoT and On-Chip Energy Harvester Applications
The power saving issue and clean energy harvesting for wireless and cost-affordable electronics (e.g., IoT applications, sensor nodes or medical implants), have recently become attractive research topics. With this in mind, the paper addresses one of the most important parts of the energy conversion system chain – the power management unit. The core of such a unit will be formed by an inductorless, low-voltage DC-DC converter based on the cross-coupled dynamic-threshold charge pump topology. The charge pump utilizes a power-efficient ON/OFF regulation feedback loop, specially designed for strict low-voltage start-up conditions by a driver booster. Taken together, they serve as the masters to control the charge pump output (up to 600 mV), depending on the voltage value produced by a renewable energy source available in the environment. The low-power feature is also ensured by a careful design of the hysteresis-based bulk-driven comparator and fully integrated switched-capacitor voltage divider, omitting the static power consumption. The presented converter can also employ the on-chip RF-based energy harvester for use in a wireless power transfer system.
Open AccessLow-Voltage DC-DC Converter for IoT and On-Chip Energy Harvester Applications
The power saving issue and clean energy harvesting for wireless and cost-affordable electronics (e.g., IoT applications, sensor nodes or medical implants), have recently become attractive research topics. With this in mind, the paper addresses one of the most important parts of the energy conversion system chain – the power management unit. The core of such a unit will be formed by an inductorless, low-voltage DC-DC converter based on the cross-coupled dynamic-threshold charge pump topology. The charge pump utilizes a power-efficient ON/OFF regulation feedback loop, specially designed for strict low-voltage start-up conditions by a driver booster. Taken together, they serve as the masters to control the charge pump output (up to 600 mV), depending on the voltage value produced by a renewable energy source available in the environment. The low-power feature is also ensured by a careful design of the hysteresis-based bulk-driven comparator and fully integrated switched-capacitor voltage divider, omitting the static power consumption. The presented converter can also employ the on-chip RF-based energy harvester for use in a wireless power transfer system.
- Open Access
- 16 June 2021
- Published by IntechOpen
Digital On-Chip Calibration of Analog Systems towards Enhanced Reliability
This chapter deals with digital method of calibration for analog integrated circuits as a means of extending its lifetime and reliability, which consequently affects the reliability the analog electronic system as a whole. The proposed method can compensate for drift in circuit’s electrical parameters, which occurs either in a long term due to aging and electrical stress or it is rather more acute, being caused by process, voltage and temperature variations. The chapter reveals the implementation of ultra-low voltage on-chip system of digitally calibrated variable-gain amplifier (VGA), fabricated in CMOS 130 nm technology. It operates reliably under supply voltage of 600mV with 10% variation, in temperature range from −20°C to 85°C. Simulations suggest that the system will preserve its parameters for at least 10 years of operation. Experimental verification over 10 packaged integrated circuit (IC) samples shows the input offset voltage of VGA is suppressed in range of 13μV to 167μV. With calibration the VGA closely meets its nominally designed essential specifications as voltage gain or bandwidth. Digital calibration is comprehensively compared to its widely used alternative, Chopper stabilization through its implementation for the same VGA.
- 16 June 2021
- Published by IntechOpen
Open AccessDigital On-Chip Calibration of Analog Systems towards Enhanced Reliability
This chapter deals with digital method of calibration for analog integrated circuits as a means of extending its lifetime and reliability, which consequently affects the reliability the analog electronic system as a whole. The proposed method can compensate for drift in circuit’s electrical parameters, which occurs either in a long term due to aging and electrical stress or it is rather more acute, being caused by process, voltage and temperature variations. The chapter reveals the implementation of ultra-low voltage on-chip system of digitally calibrated variable-gain amplifier (VGA), fabricated in CMOS 130 nm technology. It operates reliably under supply voltage of 600mV with 10% variation, in temperature range from −20°C to 85°C. Simulations suggest that the system will preserve its parameters for at least 10 years of operation. Experimental verification over 10 packaged integrated circuit (IC) samples shows the input offset voltage of VGA is suppressed in range of 13μV to 167μV. With calibration the VGA closely meets its nominally designed essential specifications as voltage gain or bandwidth. Digital calibration is comprehensively compared to its widely used alternative, Chopper stabilization through its implementation for the same VGA.
- 1 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Adverse effects of digital calibration hardware on low-voltage operational amplifiers
This paper presents the analysis of digital calibration adverse effects, that arise from the connection of the calibration circuit to an operational amplifier being the circuit under calibration. In this way, the amplifier transfer function is affected and so are the frequency characteristics. Principles of the proposed calibration method are described. The calibration system was implemented in 130 nm CMOS technology node. In order to estimate arising adverse effects of calibration hardware on the amplifier performance, the small-signal analysis was performed. The detailed simulation results revealed the worst-case reduction of the VGA bandwidth to 87% and reduction of the gain-bandwidth to 75% with the calibration circuit connected. In the simulation analysis carried out, also mismatch, process parameters fluctuations and temperature variations have been considered.
- 1 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Adverse effects of digital calibration hardware on low-voltage operational amplifiers
This paper presents the analysis of digital calibration adverse effects, that arise from the connection of the calibration circuit to an operational amplifier being the circuit under calibration. In this way, the amplifier transfer function is affected and so are the frequency characteristics. Principles of the proposed calibration method are described. The calibration system was implemented in 130 nm CMOS technology node. In order to estimate arising adverse effects of calibration hardware on the amplifier performance, the small-signal analysis was performed. The detailed simulation results revealed the worst-case reduction of the VGA bandwidth to 87% and reduction of the gain-bandwidth to 75% with the calibration circuit connected. In the simulation analysis carried out, also mismatch, process parameters fluctuations and temperature variations have been considered.
- 1 January 2018
- Published by Elsevier in Microelectronics Reliability
- Vol. 80, 155-163
Ultra-low-voltage boosted driver for self-powered systems
- 1 January 2018
- Published by Elsevier in Microelectronics Reliability
- Vol. 80, 155-163
Ultra-low-voltage boosted driver for self-powered systems
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Digital methods of calibration for analog integrated circuits in nanotechnologies
This work deals with the influence of increasing rate of integration (i.e. technology downscale) on the main parameters of integrated circuits. Our concerns are focused on calibration methods of analog integrated circuits that can compensate undesired side effects of technology downscale. The paper describes both the general principle of calibration system as well as design requirements for main blocks of the calibration subcircuit. Then, the approach for calibration employment in operational amplifiers is described, where the voltage offset cancellation is of the main concern. Consequently, a specific application of previously described calibration fundamentals is presented. For this purpose, statistical results on the input offset voltage of the operational amplifier are used, where the operational amplifier is realized in 130 nm CMOS technology.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Digital methods of calibration for analog integrated circuits in nanotechnologies
This work deals with the influence of increasing rate of integration (i.e. technology downscale) on the main parameters of integrated circuits. Our concerns are focused on calibration methods of analog integrated circuits that can compensate undesired side effects of technology downscale. The paper describes both the general principle of calibration system as well as design requirements for main blocks of the calibration subcircuit. Then, the approach for calibration employment in operational amplifiers is described, where the voltage offset cancellation is of the main concern. Consequently, a specific application of previously described calibration fundamentals is presented. For this purpose, statistical results on the input offset voltage of the operational amplifier are used, where the operational amplifier is realized in 130 nm CMOS technology.