Yılmaz Türk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Yılmaz Türk has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Abdurrahim Aydın
Duzce Universitesi
5 shared publications - Remzi Eker
İzmir Katip Çelebi Üniversitesi Orman Fakültesi
4 shared publications - Tunahan Çınar
Düzce University
4 shared publications - Berkan Balaban
Institute of Postgraduate Education Düzce University Düzce TURKEY
3 shared publications - Selçuk Gümüş
Karadeniz Teknik Üniversitesi
3 shared publications Mücahit Bodur
Department of Forest Engineering, Faculty of Forest, Düzce University, Düzce, Turkey
2 shared publications
Latest Publications
- Open Access
- 25 December 2025
- Published by European Journal of Forest Engineering in European Journal of Forest Engineering
- Vol. 11 (2) , 106-114
Productivity Analysis of Roadside Loading with a Truck-Mounted Hydraulic Crane Using a Regression Tree Model
Timber loading operations play a crucial role in the seamless execution of forest production activities. In this study, the productivity of the truck-mounted hydraulic crane, which used for loading timbers, was analyzed using the time study method. Additionally, the loader's productivity was statistically evaluated according to affecting factors. The study was conducted in the production activities carried out within the boundaries of the Kayadibi Forest Enterprise Chief of the Arhavi Forest Enterprise Directorate in Artvin province of Türkiye. According to the study results, the average productivity of loading operations with the truck-mounted hydraulic crane was found to be 34.28 m3/hour. It was determined that the most time-consuming phase in a loading cycle was placing the timbers and releasing the timbers onto the logging truck (32.86%), and the approaching time to the timber was the least time-consuming phase (11.39%). Additionally, the delay time was found to account for 24.76% of the total cycle time. According to the correlation test results, there was a strong, positive, and significant relationship (p < 0.001) at the 99% confidence level between productivity and both product diameter and volume. The regression tree model yielded an R² value of 0.7, with the volume variable contributing the most (99%) as an independent factor.
- 25 December 2025
- Published by European Journal of Forest Engineering in European Journal of Forest Engineering
- Vol. 11 (2) , 106-114
Open AccessProductivity Analysis of Roadside Loading with a Truck-Mounted Hydraulic Crane Using a Regression Tree Model
Timber loading operations play a crucial role in the seamless execution of forest production activities. In this study, the productivity of the truck-mounted hydraulic crane, which used for loading timbers, was analyzed using the time study method. Additionally, the loader's productivity was statistically evaluated according to affecting factors. The study was conducted in the production activities carried out within the boundaries of the Kayadibi Forest Enterprise Chief of the Arhavi Forest Enterprise Directorate in Artvin province of Türkiye. According to the study results, the average productivity of loading operations with the truck-mounted hydraulic crane was found to be 34.28 m3/hour. It was determined that the most time-consuming phase in a loading cycle was placing the timbers and releasing the timbers onto the logging truck (32.86%), and the approaching time to the timber was the least time-consuming phase (11.39%). Additionally, the delay time was found to account for 24.76% of the total cycle time. According to the correlation test results, there was a strong, positive, and significant relationship (p < 0.001) at the 99% confidence level between productivity and both product diameter and volume. The regression tree model yielded an R² value of 0.7, with the volume variable contributing the most (99%) as an independent factor.
- Open Access
- 30 January 2025
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 13 (1) , 443-455
Determination of Excavation Volume Using UAV-Based PPK Method in Open Mining Sites Tatlıdere Forests in Düzce
Remote sensing technologies have the potential to provide cost-effective, fast, and easy solutions for the determination of surface changes (material volume) after quarrying (open-pit mine) activities. In areas where the topography is rugged and difficult to access, the use of ground measurement techniques causes difficulties. In such cases, the use of remote sensing techniques is indispensable. The Post Processing Kinematic (PPK) measurement technique provides an alternative solution to other photogrammetry methods in areas whose topography is not suitable for satellite-based positioning. This study investigates the applicability of the UAV based PPK method for the calculation of cut volume in quarry operations. The study area was selected as a quarry located within the boundaries of Tatlıdere Forestry Operation Chief in Düzce province and operated by a legal entity. Using a DJI Phantom 4 RTK unmanned aerial vehicle (UAV) with a PPK application module, a total of two flights in PPK flight mode were performed at the quarry on 30 September 2021 and 19 May 2022 (covering a period of approximately 7 months). The material volume, which is important for quarry operation, was calculated and the excavation volume in the two flight time intervals was found to be 104.170 m³ and the cut area was found to be 44.348 m2. According to the results obtained, UAV systems should be used in quarry management in terms of time and work safety in obtaining data.
- 30 January 2025
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 13 (1) , 443-455
Open AccessDetermination of Excavation Volume Using UAV-Based PPK Method in Open Mining Sites Tatlıdere Forests in Düzce
Remote sensing technologies have the potential to provide cost-effective, fast, and easy solutions for the determination of surface changes (material volume) after quarrying (open-pit mine) activities. In areas where the topography is rugged and difficult to access, the use of ground measurement techniques causes difficulties. In such cases, the use of remote sensing techniques is indispensable. The Post Processing Kinematic (PPK) measurement technique provides an alternative solution to other photogrammetry methods in areas whose topography is not suitable for satellite-based positioning. This study investigates the applicability of the UAV based PPK method for the calculation of cut volume in quarry operations. The study area was selected as a quarry located within the boundaries of Tatlıdere Forestry Operation Chief in Düzce province and operated by a legal entity. Using a DJI Phantom 4 RTK unmanned aerial vehicle (UAV) with a PPK application module, a total of two flights in PPK flight mode were performed at the quarry on 30 September 2021 and 19 May 2022 (covering a period of approximately 7 months). The material volume, which is important for quarry operation, was calculated and the excavation volume in the two flight time intervals was found to be 104.170 m³ and the cut area was found to be 44.348 m2. According to the results obtained, UAV systems should be used in quarry management in terms of time and work safety in obtaining data.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 31
Determination of forest road cut slope surface material types using machine learning methods in UAV data
Background: The cost of forest roads is practically estimated by determining the Surface Material Types (SMT). Experts determine SMT by classifying soil, loose soil, and rocky surface material classes (%) through in-situ measurements, which are both costly and time-intensive. This study aims to reduce cost and time loss by evaluating the effectiveness of high-resolution remote sensing (RS) data in determining SMT. Conducted on a forest road in Konuralp region of Düzce district in Türkiye, the study involved experts classifying the road’s Soil, Loose Soil and Rocky surface material classes (%) and collecting high-resolution RS data using UAV. The RS data was processed through Random Forest (RF) and Support Vector Machine (SVM) algorithms to classify the surface material types, and their accuracy was assessed using the Kappa Coefficient, Overall Accuracy (%) and Conditional Kappa. The images were clipped at 20-meter intervals for detailed analysis. The RS data classifications were then compared with in-situ measurements using statistical analyses Index-of-Agreement (IA). Results: The RF algorithm made the best identification, although the classification of the Loose Soil class was more difficult for both algorithms compared to the other classes. Both algorithms highest accuracy in identifying the Rocky class. Conclusions: This study proposes methods to reduce time loss in cost calculations and enhance the use of RS images for estimating forest road costs.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 31
Open AccessDetermination of forest road cut slope surface material types using machine learning methods in UAV data
Background: The cost of forest roads is practically estimated by determining the Surface Material Types (SMT). Experts determine SMT by classifying soil, loose soil, and rocky surface material classes (%) through in-situ measurements, which are both costly and time-intensive. This study aims to reduce cost and time loss by evaluating the effectiveness of high-resolution remote sensing (RS) data in determining SMT. Conducted on a forest road in Konuralp region of Düzce district in Türkiye, the study involved experts classifying the road’s Soil, Loose Soil and Rocky surface material classes (%) and collecting high-resolution RS data using UAV. The RS data was processed through Random Forest (RF) and Support Vector Machine (SVM) algorithms to classify the surface material types, and their accuracy was assessed using the Kappa Coefficient, Overall Accuracy (%) and Conditional Kappa. The images were clipped at 20-meter intervals for detailed analysis. The RS data classifications were then compared with in-situ measurements using statistical analyses Index-of-Agreement (IA). Results: The RF algorithm made the best identification, although the classification of the Loose Soil class was more difficult for both algorithms compared to the other classes. Both algorithms highest accuracy in identifying the Rocky class. Conclusions: This study proposes methods to reduce time loss in cost calculations and enhance the use of RS images for estimating forest road costs.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 31, e-103473
UAVs monitoring of open-pit mining site rehabilitation in mountainous forest areas: the case of the Turkey-Western Black Sea Region
Background: Mining has a long history and significantly impacts national economies, but it also causes considerable environmental damage. Forest areas are particularly affected, and sustainable management practices are essential for natural resource utilization. Effective rehabilitation of open-pit mining sites is crucial before, during, and after mining operations This study focuses on the rehabilitation process of an open-pit mining site located at the boundary of mountainous forest areas. Landform (slope geometries) measurements and boundary checks were conducted using the UAV-based PPK method. UAV flights were conducted at two different times over a period of approximately seven months. Orthophoto images and DEMs from both flights were used to measure slope width, height, and angle, and to monitor boundary violations during the rehabilitation process. The calculation of slope geometry values was performed using ArcGIS software.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 31, e-103473
Open AccessUAVs monitoring of open-pit mining site rehabilitation in mountainous forest areas: the case of the Turkey-Western Black Sea Region
Background: Mining has a long history and significantly impacts national economies, but it also causes considerable environmental damage. Forest areas are particularly affected, and sustainable management practices are essential for natural resource utilization. Effective rehabilitation of open-pit mining sites is crucial before, during, and after mining operations This study focuses on the rehabilitation process of an open-pit mining site located at the boundary of mountainous forest areas. Landform (slope geometries) measurements and boundary checks were conducted using the UAV-based PPK method. UAV flights were conducted at two different times over a period of approximately seven months. Orthophoto images and DEMs from both flights were used to measure slope width, height, and angle, and to monitor boundary violations during the rehabilitation process. The calculation of slope geometry values was performed using ArcGIS software.
- Open Access
- 28 December 2024
- Published by Duzce University in Düzce Üniversitesi Orman Fakültesi Ormancılık Dergisi
- Vol. 20 (2) , 1-14
Determination of Material Volume Using UAVs in Land Surface Change: The Case of Konuralp Campus (Düzce)
In this study examined the availability of UAV in determining material volume in excavation and fill works. The study aims on calculating the volume of an excavation work areas 1841 m² at the parking lot of the Faculty of Sports Sciences at Düzce University Konuralp Campus and a filling work areas 2759 m² on the access road to the Environmental and Health Specialization Laboratory. Autonomous UAV flights were performed before and after the excavation and filling works in the study areas. Besides, following these UAV flights, terrestrial measurements were made in the same way. The study was founded that UAV data analysis results an excavation volume of 7121 m³ in the parking area and a filling volume of 5752 m³ on the road. According to calculations used terrestrial measurement methods, the excavation volume in the parking area was 7007 m³ and the filling volume on the road was 5683 m³. An average difference of 1.42% was found between UAV data and terrestrial measurement methods. The results were showed the usability of UAV systems in detected material volume.
- 28 December 2024
- Published by Duzce University in Düzce Üniversitesi Orman Fakültesi Ormancılık Dergisi
- Vol. 20 (2) , 1-14
Open AccessDetermination of Material Volume Using UAVs in Land Surface Change: The Case of Konuralp Campus (Düzce)
In this study examined the availability of UAV in determining material volume in excavation and fill works. The study aims on calculating the volume of an excavation work areas 1841 m² at the parking lot of the Faculty of Sports Sciences at Düzce University Konuralp Campus and a filling work areas 2759 m² on the access road to the Environmental and Health Specialization Laboratory. Autonomous UAV flights were performed before and after the excavation and filling works in the study areas. Besides, following these UAV flights, terrestrial measurements were made in the same way. The study was founded that UAV data analysis results an excavation volume of 7121 m³ in the parking area and a filling volume of 5752 m³ on the road. According to calculations used terrestrial measurement methods, the excavation volume in the parking area was 7007 m³ and the filling volume on the road was 5683 m³. An average difference of 1.42% was found between UAV data and terrestrial measurement methods. The results were showed the usability of UAV systems in detected material volume.
- Open Access
- 12 November 2024
- Published by University of Zagreb, Faculty of Forestry and Wood Technology in Croatian journal of forest engineering
- Vol. 46 (1) , 119-139
Examining Open-Top Culverts Impact on Forest Road Surface Deteriorations via UAVs
The life and robustness of forest roads depend on their protection from the harmful effects of water coming into the road surface. In particular, the deterioration of the road surface affects the safe navigation of vehicles and traffic safety. This situation requires that the surface be stable on forest roads. The aim of the study is to examine whether surface deterioration (erosion and accumulation) on forest roads due to the drainage problem of water falling on the road surface can be minimized by open-top culverts and to determine their effectiveness. These are used in three separate trial blocks every 25 m (A parcels; total of 3 parcels), every 50 m (B parcels; total of 3 parcels) and control block (C). Volumetric erosion and accumulation in these blocks was compared by UAV for about 3 years and the effectiveness of the open-top culverts was examined by this method. A 500 m section of the forest road coded 001 of the Kardüz Forest Operations Directorate (Düzce/Türkiye) was examined in the study. As a result, erosion and accumulation in all blocks have been found to have a dynamic course. It was determined that this mobility was greater in the control block than in the blocks with open-top culverts installed at intervals of 25 m and 50 m. The mean Z values for the blocks showed that the deterioration in the control block (C) was higher than in the blocks with 25 m and 50 m open culverts. The volumetric deterioration rate was 5 times higher in the control block than in the block installed at 25 m interval (A plots) and 2 times higher than in the block installed at 50 m interval (B plots). Similarly, the areal deterioration rate was 3.3 times higher in the control block than in the block installed at 25 m interval (A plots) and 1.4 times higher than in the block installed at 50 m interval (B plots). These results showed the effectiveness of open-top culverts and it was also determined that the open-top culverts installed at 25 m intervals were more effective than the open-top culverts established at 50 m intervals. In addition, according to the statistical analysis, a statistically significant difference was found between the erosion volume in the blocks. Open-top culverts should be used against forest road surface deterioration and UAV technology should be used for deterioration detection.
- 12 November 2024
- Published by University of Zagreb, Faculty of Forestry and Wood Technology in Croatian journal of forest engineering
- Vol. 46 (1) , 119-139
Open AccessExamining Open-Top Culverts Impact on Forest Road Surface Deteriorations via UAVs
The life and robustness of forest roads depend on their protection from the harmful effects of water coming into the road surface. In particular, the deterioration of the road surface affects the safe navigation of vehicles and traffic safety. This situation requires that the surface be stable on forest roads. The aim of the study is to examine whether surface deterioration (erosion and accumulation) on forest roads due to the drainage problem of water falling on the road surface can be minimized by open-top culverts and to determine their effectiveness. These are used in three separate trial blocks every 25 m (A parcels; total of 3 parcels), every 50 m (B parcels; total of 3 parcels) and control block (C). Volumetric erosion and accumulation in these blocks was compared by UAV for about 3 years and the effectiveness of the open-top culverts was examined by this method. A 500 m section of the forest road coded 001 of the Kardüz Forest Operations Directorate (Düzce/Türkiye) was examined in the study. As a result, erosion and accumulation in all blocks have been found to have a dynamic course. It was determined that this mobility was greater in the control block than in the blocks with open-top culverts installed at intervals of 25 m and 50 m. The mean Z values for the blocks showed that the deterioration in the control block (C) was higher than in the blocks with 25 m and 50 m open culverts. The volumetric deterioration rate was 5 times higher in the control block than in the block installed at 25 m interval (A plots) and 2 times higher than in the block installed at 50 m interval (B plots). Similarly, the areal deterioration rate was 3.3 times higher in the control block than in the block installed at 25 m interval (A plots) and 1.4 times higher than in the block installed at 50 m interval (B plots). These results showed the effectiveness of open-top culverts and it was also determined that the open-top culverts installed at 25 m intervals were more effective than the open-top culverts established at 50 m intervals. In addition, according to the statistical analysis, a statistically significant difference was found between the erosion volume in the blocks. Open-top culverts should be used against forest road surface deterioration and UAV technology should be used for deterioration detection.
- Open Access
- 26 March 2024
- Published by Hrvatsko Sumarsko Drustvo in Šumarski list
- Vol. 148 (3-4) , 139-152
Capabılıtıes of usıng UAVs to determıne forest road excavatıon volumes ın mountaınous areas
Decision support systems based on spatial data are widely used in some countries for planning production activitiesin forestry and designing forest roads. In recent years, Unmanned Aerial Vehicles (UAVs) have been playingan active role in the production of high resolution and accurate digital elevation models (DEMs) of forested areas.In the preparation of progress payments for forest road construction works, the workload is high, while the feethat has to be paid to the contractor company after the completion of the road construction is determined accordingto the final cost in the progress payment schedules. In this study, the applicability of UAV technology for determiningforest road cut volume and land classification was investigated. A 640-meter section of the forest roadcoded 001 of Taşlıyayla Forest Management Sub-Directorate (Bolu/Türkiye) was examined in the study. Flightswith an UAV (drone) were carried out in autonomous mode before and after the construction of the road examinedin the study. In addition, in order to determine the amount of cut, measurements of the geometric characteristicsof the road were made in the field after the road construction. As a result of the study, 2189 m³ cut volumewas found with the UAV data with an average error of 3 cm. According to the field measurement results, theamount of cut was determined as 2080 m³. A difference of +5% was found between the UAV data and the fieldmeasurement results. In addition, using the JavaScript coding language on the Google Earth Engine platform, soil(46%) and loose soil (54%) land classification was identified from the orthophoto images. The obtained resultsreveal the usability of UAVs in determining forest road volumes.
- 26 March 2024
- Published by Hrvatsko Sumarsko Drustvo in Šumarski list
- Vol. 148 (3-4) , 139-152
Open AccessCapabılıtıes of usıng UAVs to determıne forest road excavatıon volumes ın mountaınous areas
Decision support systems based on spatial data are widely used in some countries for planning production activitiesin forestry and designing forest roads. In recent years, Unmanned Aerial Vehicles (UAVs) have been playingan active role in the production of high resolution and accurate digital elevation models (DEMs) of forested areas.In the preparation of progress payments for forest road construction works, the workload is high, while the feethat has to be paid to the contractor company after the completion of the road construction is determined accordingto the final cost in the progress payment schedules. In this study, the applicability of UAV technology for determiningforest road cut volume and land classification was investigated. A 640-meter section of the forest roadcoded 001 of Taşlıyayla Forest Management Sub-Directorate (Bolu/Türkiye) was examined in the study. Flightswith an UAV (drone) were carried out in autonomous mode before and after the construction of the road examinedin the study. In addition, in order to determine the amount of cut, measurements of the geometric characteristicsof the road were made in the field after the road construction. As a result of the study, 2189 m³ cut volumewas found with the UAV data with an average error of 3 cm. According to the field measurement results, theamount of cut was determined as 2080 m³. A difference of +5% was found between the UAV data and the fieldmeasurement results. In addition, using the JavaScript coding language on the Google Earth Engine platform, soil(46%) and loose soil (54%) land classification was identified from the orthophoto images. The obtained resultsreveal the usability of UAVs in determining forest road volumes.
- 15 January 2024
- Published by Springer Nature in Environmental Monitoring and Assessment
- Vol. 196 (2) , 1-18
Capabilities of using UAVs and close range photogrammetry to determine short-term soil losses in forest road cut slopes in semi-arid mountainous areas
The soil losses that are caused should be examined by monitoring the forest roads in the periods after they are built. In traditional soil loss determination studies that require intensive labour, due to difficulties in parcel setup, leaks from the connection points of the system, overflow of the material in the storage units and regular follow-up of the precipitation, etc., the system has its disadvantages. In this study, studies were carried out to evaluate the possibilities of using UAV and close range photogrammetry (CRP) methods, which are remote sensing techniques, and to determine the soil losses in forest road cut slopes in semi-arid mountainous areas. In addition, the advantages and disadvantages of the methods are discussed. A 100-m section of the secondary forest road was chosen as the study area. Data acquisition was carried out by UAV and CRP methods in the period of May 2020–November 2020. In the results of the study, the volumetric deformation per unit area results, a − 0.0060 m3m−2 erosion amount and a 0.0046 m3m−2 accumulation amount were determined by UAV. In addition, in the photogrammetric method, a − 0.0050 m3m−2 erosion amount and a 0.0031 m3m−2 accumulation amount were found. When both methods were compared temporally, the processes took approximately 2 times longer in the CRP method. In addition, while the ground sampling distance of DEMs and orthophotos produced with the UAV was 2 cm, it was obtained as 1 cm in the CRP method and terrestrial receptions were found to be 2 times higher resolution. According to the results obtained, the CRP method gives results that are more accurate in such studies.
- 15 January 2024
- Published by Springer Nature in Environmental Monitoring and Assessment
- Vol. 196 (2) , 1-18
Capabilities of using UAVs and close range photogrammetry to determine short-term soil losses in forest road cut slopes in semi-arid mountainous areas
The soil losses that are caused should be examined by monitoring the forest roads in the periods after they are built. In traditional soil loss determination studies that require intensive labour, due to difficulties in parcel setup, leaks from the connection points of the system, overflow of the material in the storage units and regular follow-up of the precipitation, etc., the system has its disadvantages. In this study, studies were carried out to evaluate the possibilities of using UAV and close range photogrammetry (CRP) methods, which are remote sensing techniques, and to determine the soil losses in forest road cut slopes in semi-arid mountainous areas. In addition, the advantages and disadvantages of the methods are discussed. A 100-m section of the secondary forest road was chosen as the study area. Data acquisition was carried out by UAV and CRP methods in the period of May 2020–November 2020. In the results of the study, the volumetric deformation per unit area results, a − 0.0060 m3m−2 erosion amount and a 0.0046 m3m−2 accumulation amount were determined by UAV. In addition, in the photogrammetric method, a − 0.0050 m3m−2 erosion amount and a 0.0031 m3m−2 accumulation amount were found. When both methods were compared temporally, the processes took approximately 2 times longer in the CRP method. In addition, while the ground sampling distance of DEMs and orthophotos produced with the UAV was 2 cm, it was obtained as 1 cm in the CRP method and terrestrial receptions were found to be 2 times higher resolution. According to the results obtained, the CRP method gives results that are more accurate in such studies.
- Open Access
- 6 December 2023
- Published by Kastamonu University in Kastamonu University Journal of Forestry Faculty
- Vol. 23 (3) , 264-281
Investigation of the Effect of Topography and Stand Structure on Windthrow Damages: A Case Study from Düzce, Türkiye
Aim of study: The aim of the study was to determined the tree volume and damage level in windthrow areas and to assess the impact of topographic factors and forest structure on windthrow damaged. Area of study: Our study was conducted within the Düzce Forest Management Directorate. Material and methods: The windthrow areas within the boundaries of Düzce Forest Management Directorate were obtained from extraordinary yield reports. According to windthrow data verified using Google Earth, the borders for each damage were determined and transferred to ArcMap. The relationships between windthrow areas and enviromental parameters were determined using digital maps and forest management plans. Correlation analysis was applied to find out the relationship between windthrow areas and topographic and forest characteristics. Additionally, variance analysis was performed to determine if there were differences in terms of dominant aspects and forest types between windthrow areas and amounts. T-tests were conducted to determine if there were differences between windthrow areas and amounts and the dominant wind direction. Based on the statistically significant results, an intersect analysis was applied to environmental parameters to generate a windthrow susceptibility map. Main results: Windthrow occurred mostly in the southwest aspect, in the Fir-Beech species and in the cd age classes. A statistically significant relationship (p
- 6 December 2023
- Published by Kastamonu University in Kastamonu University Journal of Forestry Faculty
- Vol. 23 (3) , 264-281
Open AccessInvestigation of the Effect of Topography and Stand Structure on Windthrow Damages: A Case Study from Düzce, Türkiye
Aim of study: The aim of the study was to determined the tree volume and damage level in windthrow areas and to assess the impact of topographic factors and forest structure on windthrow damaged. Area of study: Our study was conducted within the Düzce Forest Management Directorate. Material and methods: The windthrow areas within the boundaries of Düzce Forest Management Directorate were obtained from extraordinary yield reports. According to windthrow data verified using Google Earth, the borders for each damage were determined and transferred to ArcMap. The relationships between windthrow areas and enviromental parameters were determined using digital maps and forest management plans. Correlation analysis was applied to find out the relationship between windthrow areas and topographic and forest characteristics. Additionally, variance analysis was performed to determine if there were differences in terms of dominant aspects and forest types between windthrow areas and amounts. T-tests were conducted to determine if there were differences between windthrow areas and amounts and the dominant wind direction. Based on the statistically significant results, an intersect analysis was applied to environmental parameters to generate a windthrow susceptibility map. Main results: Windthrow occurred mostly in the southwest aspect, in the Fir-Beech species and in the cd age classes. A statistically significant relationship (p
- 16 November 2023
- Published by Springer Nature in Environmental Monitoring and Assessment
- Vol. 195 (12) , 1-17
Assessment and analysis of tree damage caused by forest road construction in a scotch pine stand: a case study from Alabarda/Bolu-Türkiye
The aim of this study is to determine the forest road construction area and environmental impact area and to determine the tree injuries caused by forest road construction, the filling area covering the stand, and the distances of the trees directly affected by the tree injuries from the road axis. For this objective, a 700-m section of the forest road number 194 within the boundaries of the Alabarda Forest Management Sub-Directorate (Bolu/Turkey) was selected as the study area. The forest road environmental impact area was found by determining the rolling boundary of the backfill material with the differential global positioning system (DGPS) device. In addition, the position of the trees in this area in relation to the road and their damage conditions were determined, and wound sizes were measured. As a result of the study, the road construction impact area was 46479 m2, the average spread distance of the backfill material was 50.34 m, the average distance of the damaged trees from the road was 28.25 m, and the average distance of the trees that were not damaged was 35.52 m. In addition, a total of 1477 trees were identified in the construction impact area and 427 of these trees were damaged. According to the results of the statistical analyses, a statistically significant positive correlation was determined between bark wound area and diameter. In addition, a statistically significant negative correlation was determined between the distance of the trees from the road axis and the wound area and the height of the backfill.
- 16 November 2023
- Published by Springer Nature in Environmental Monitoring and Assessment
- Vol. 195 (12) , 1-17
Assessment and analysis of tree damage caused by forest road construction in a scotch pine stand: a case study from Alabarda/Bolu-Türkiye
The aim of this study is to determine the forest road construction area and environmental impact area and to determine the tree injuries caused by forest road construction, the filling area covering the stand, and the distances of the trees directly affected by the tree injuries from the road axis. For this objective, a 700-m section of the forest road number 194 within the boundaries of the Alabarda Forest Management Sub-Directorate (Bolu/Turkey) was selected as the study area. The forest road environmental impact area was found by determining the rolling boundary of the backfill material with the differential global positioning system (DGPS) device. In addition, the position of the trees in this area in relation to the road and their damage conditions were determined, and wound sizes were measured. As a result of the study, the road construction impact area was 46479 m2, the average spread distance of the backfill material was 50.34 m, the average distance of the damaged trees from the road was 28.25 m, and the average distance of the trees that were not damaged was 35.52 m. In addition, a total of 1477 trees were identified in the construction impact area and 427 of these trees were damaged. According to the results of the statistical analyses, a statistically significant positive correlation was determined between bark wound area and diameter. In addition, a statistically significant negative correlation was determined between the distance of the trees from the road axis and the wound area and the height of the backfill.