Maria Paola Santisi D'AVila
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Maria Paola Santisi D'AVila has a total of 92 co-authors. Here are the top co-authors by number of shared publications:
- Luca Lenti
Université Paris Est, IFSTTAR, 75015 Paris, France
7 shared publications Luca Lenti
CEREMA, Repsody, Sophia Antipolis, France
4 shared publications- Anne Deschamps
Université Côte d’Azur, CNRS, IRD, Observatoire de la Côte d’Azur, Géoazur, France
3 shared publications - Céline Gélis
Institute for Radiological protection and Nuclear Safety
3 shared publications E. Diego Mercerat
CEREMA, Direction territoriale Méditerranée 56 bd Stalingrad 06359 Nice France
3 shared publicationsEtienne Bertrand
CEREMA, Direction territoriale Méditerranée 56 bd Stalingrad 06359 Nice France
3 shared publications
Latest Publications
- Open Access
- 9 November 2026
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 213
Modeling methodology for compressed earth block gravity masonry walls under seismic loading
- 9 November 2026
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 213
Open AccessModeling methodology for compressed earth block gravity masonry walls under seismic loading
- Open Access
Comparison of Methodologies for the Behavior Factor Estimation in Seismic Design of Buildings: Case Study of Geo-Sourced Masonry Construction
The behavior factor, which represents the force reduction that a structure would experience if its response was completely elastic compared with the seismic forces used for design, is defined in seismic design codes for common construction techniques and materials. A specific assessment is needed when novel construction materials are adopted. The lack of accurate structural performance estimations limits the use of green construction materials because building codes only allow the use of minimum values for the behavior factor. This research aims to verify the reliability of the proposed capacity-demand-based (CDB) method for the estimation of the force reduction factor and behavior factor, by comparison with other procedures such as demand-based, capacity-based and formula-based approaches. The main characteristic of the proposed approach is that the ductility-FRF curve is obtained numerically for the building natural period, instead of imposing an analytical FRF-ductility-period relationship. The advantage of the CDB-method is its efficiency from a computational point of view without restrictions concerning the construction material and structural typology. The results are compared in the case where dynamic analyses are performed for a three-dimensional (3D) building model (considered as a reference) and for an equivalent single-degree-of-freedom system which reduces the computation time. The CDB-method yields safe results compared with the N2 method, and it is consistent with a capacity-based approach applied to the 3D building model.
Open AccessComparison of Methodologies for the Behavior Factor Estimation in Seismic Design of Buildings: Case Study of Geo-Sourced Masonry Construction
The behavior factor, which represents the force reduction that a structure would experience if its response was completely elastic compared with the seismic forces used for design, is defined in seismic design codes for common construction techniques and materials. A specific assessment is needed when novel construction materials are adopted. The lack of accurate structural performance estimations limits the use of green construction materials because building codes only allow the use of minimum values for the behavior factor. This research aims to verify the reliability of the proposed capacity-demand-based (CDB) method for the estimation of the force reduction factor and behavior factor, by comparison with other procedures such as demand-based, capacity-based and formula-based approaches. The main characteristic of the proposed approach is that the ductility-FRF curve is obtained numerically for the building natural period, instead of imposing an analytical FRF-ductility-period relationship. The advantage of the CDB-method is its efficiency from a computational point of view without restrictions concerning the construction material and structural typology. The results are compared in the case where dynamic analyses are performed for a three-dimensional (3D) building model (considered as a reference) and for an equivalent single-degree-of-freedom system which reduces the computation time. The CDB-method yields safe results compared with the N2 method, and it is consistent with a capacity-based approach applied to the 3D building model.
- Open Access
- 24 September 2024
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 187
Seismic design of a low-carbon building constructed with in-situ produced compressed earth blocks
- 24 September 2024
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 187
Open AccessSeismic design of a low-carbon building constructed with in-situ produced compressed earth blocks
- Open Access
- 4 July 2023
- Published by MDPI AG in Geotechnics
- Vol. 3 (3) , 601-623
Rocking Motion Analysis Using Structural Identification Tools
This research investigates the convenience of structural identification tools to detect the rocking motion tendency, using as input the structural response to ambient vibrations. The rocking ratio and rocking spectrum are proposed as original tools to highlight the rocking motion and its frequency content. The proposed procedure allows the detection and quantification of rocking using only building vertical motion records in both cases of ambient vibration and earthquake. First, three-dimensional finite element models of reinforced concrete buildings are adopted to simulate the structural response to white noise vibration. Different low- and high-rise buildings are studied, having framed structure and frame–wall system, regular and irregular structure, shallow foundation and underground floors. The structural response obtained numerically is analyzed using different signal processing tools to obtain the dynamic features of buildings, and the rocking motion tendency is identified by comparison with a reference fixed base condition. Then, the reliability of the proposed methodology to detect rocking motion attitude, using only the structural motion, is verified and quantified using the proposed tools. Finally, the same approach is applied to real structural motion records of a high-rise reinforced concrete building.
- 4 July 2023
- Published by MDPI AG in Geotechnics
- Vol. 3 (3) , 601-623
Open AccessRocking Motion Analysis Using Structural Identification Tools
This research investigates the convenience of structural identification tools to detect the rocking motion tendency, using as input the structural response to ambient vibrations. The rocking ratio and rocking spectrum are proposed as original tools to highlight the rocking motion and its frequency content. The proposed procedure allows the detection and quantification of rocking using only building vertical motion records in both cases of ambient vibration and earthquake. First, three-dimensional finite element models of reinforced concrete buildings are adopted to simulate the structural response to white noise vibration. Different low- and high-rise buildings are studied, having framed structure and frame–wall system, regular and irregular structure, shallow foundation and underground floors. The structural response obtained numerically is analyzed using different signal processing tools to obtain the dynamic features of buildings, and the rocking motion tendency is identified by comparison with a reference fixed base condition. Then, the reliability of the proposed methodology to detect rocking motion attitude, using only the structural motion, is verified and quantified using the proposed tools. Finally, the same approach is applied to real structural motion records of a high-rise reinforced concrete building.
- Open Access
- 20 August 2022
- Published by Springer Nature in Advances in Bridge Engineering
- Vol. 3 (1) , 1-15
Reduced T-shaped soil domain for nonlinear dynamic soil-bridge interaction analysis
The one-directional three-component wave propagation in a T-shaped soil domain (1DT-3C) is a numerical modeling technique, in a finite element scheme, to investigate dynamic soil-structure interaction (SSI) coupled with seismic site effects, under the assumption of vertical propagation of three-component seismic motion along a horizontal multilayered soil. A three-dimensional elasto-plastic model is adopted for soils, characterized using their shear modulus reduction curve.In this research, the 1DT-3C wave propagation modeling technique is proposed as an efficient tool for bridge design to take into account directly the spatial variability of seismic loading. This approach, in the preliminary phase of bridge study and design, allows the reduction of the soil domain and the easier definition of boundary conditions, using geotechnical parameters obtained with only one borehole investigation for each pier. This leads to a gain in modeling and computational time.
- 20 August 2022
- Published by Springer Nature in Advances in Bridge Engineering
- Vol. 3 (1) , 1-15
Open AccessReduced T-shaped soil domain for nonlinear dynamic soil-bridge interaction analysis
The one-directional three-component wave propagation in a T-shaped soil domain (1DT-3C) is a numerical modeling technique, in a finite element scheme, to investigate dynamic soil-structure interaction (SSI) coupled with seismic site effects, under the assumption of vertical propagation of three-component seismic motion along a horizontal multilayered soil. A three-dimensional elasto-plastic model is adopted for soils, characterized using their shear modulus reduction curve.In this research, the 1DT-3C wave propagation modeling technique is proposed as an efficient tool for bridge design to take into account directly the spatial variability of seismic loading. This approach, in the preliminary phase of bridge study and design, allows the reduction of the soil domain and the easier definition of boundary conditions, using geotechnical parameters obtained with only one borehole investigation for each pier. This leads to a gain in modeling and computational time.
- 20 May 2022
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 159
Liquefaction assessment of silty sands: Experimental characterization and numerical calibration
- 20 May 2022
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 159
Liquefaction assessment of silty sands: Experimental characterization and numerical calibration
- 1 August 2020
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 135
Influence of the variability of soil profile properties on weak and strong seismic response
- 1 August 2020
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 135
Influence of the variability of soil profile properties on weak and strong seismic response
- 1 May 2019
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 120, 200-213
Soil-structure interaction analysis using a 1DT-3C wave propagation model
- 1 May 2019
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 120, 200-213
Soil-structure interaction analysis using a 1DT-3C wave propagation model
- 19 February 2019
- Published by Seismological Society of America (SSA) in Bulletin of the Seismological Society of America
- Vol. 109 (2) , 505-524
Nonlinear Numerical Simulation of the Soil Seismic Response to the 2012 Mw 5.9 Emilia Earthquake Considering the Variability of the Water Table Position
This research is focused on the case study of San Carlo village (Emilia‐Romagna, Italy), struck by the 20 May 2012 5.9 Emilia earthquake that caused severe damage because of widely observed soil liquefaction. In particular, it investigates the influence on nonlinearity effects of the variability of the water table depth caused by seasonal fluctuation. The one‐directional propagation of a three‐component seismic wave (1D‐3C approach), in a multilayered soil profile, is simulated using a finite‐element model and an elastoplastic constitutive behavior with hardening for the soil (Iwan’s model). The nonlinearity is described by the normalized shear modulus decay curve obtained by resonant column (RC) tests. The shear modulus is corrected during the process (Iai’s model) to consider the cyclic mobility and dilatancy of sands, depending on the actual average effective stress and the friction and dilatancy angles obtained from cyclic consolidated undrained triaxial (CTX) tests. Profiles with depth of maximum excess pore water pressure, horizontal motion, and shear strain and stress are obtained in the case of effective stress analysis (ESA), for an average position of the water table depth and for a variation of , and then compared with a total stress analysis (TSA). The variability with the water table depth of soil profile response to seismic loading is observed also in terms of hysteresis loops, time histories of the ground motion, and excess pore water pressure in the liquefiable soil layers prone to the cyclic mobility process.- 19 February 2019
- Published by Seismological Society of America (SSA) in Bulletin of the Seismological Society of America
- Vol. 109 (2) , 505-524
Nonlinear Numerical Simulation of the Soil Seismic Response to the 2012 Mw 5.9 Emilia Earthquake Considering the Variability of the Water Table Position
This research is focused on the case study of San Carlo village (Emilia‐Romagna, Italy), struck by the 20 May 2012 5.9 Emilia earthquake that caused severe damage because of widely observed soil liquefaction. In particular, it investigates the influence on nonlinearity effects of the variability of the water table depth caused by seasonal fluctuation. The one‐directional propagation of a three‐component seismic wave (1D‐3C approach), in a multilayered soil profile, is simulated using a finite‐element model and an elastoplastic constitutive behavior with hardening for the soil (Iwan’s model). The nonlinearity is described by the normalized shear modulus decay curve obtained by resonant column (RC) tests. The shear modulus is corrected during the process (Iai’s model) to consider the cyclic mobility and dilatancy of sands, depending on the actual average effective stress and the friction and dilatancy angles obtained from cyclic consolidated undrained triaxial (CTX) tests. Profiles with depth of maximum excess pore water pressure, horizontal motion, and shear strain and stress are obtained in the case of effective stress analysis (ESA), for an average position of the water table depth and for a variation of , and then compared with a total stress analysis (TSA). The variability with the water table depth of soil profile response to seismic loading is observed also in terms of hysteresis loops, time histories of the ground motion, and excess pore water pressure in the liquefiable soil layers prone to the cyclic mobility process.- 1 September 2018
- Published by Elsevier in Computers & Structures
- Vol. 207, 83-94
Analysis of nonlinear soil-structure interaction effects: 3D frame structure and 1-Directional propagation of a 3-Component seismic wave
- 1 September 2018
- Published by Elsevier in Computers & Structures
- Vol. 207, 83-94
Analysis of nonlinear soil-structure interaction effects: 3D frame structure and 1-Directional propagation of a 3-Component seismic wave