Ralf Lach
Research Subjects
Ralf Lach has a total of 87 co-authors. Here are the top co-authors by number of shared publications:
Wolfgang Grellmann
Polymer Service GmbH Merseburg (PSM) Merseburg Germany
13 shared publications- Rameshwar Adhikari
Research Centre for Applied Science and Technology (RECAST), Tribhuvan University, Kirtipur, Kathmandu
10 shared publications Sven Henning
Fraunhofer Institute for Microstructure of Materials and Systems (IMWS) Walter‐Hülse‐Straße 1 06120 Halle (Saale) Germany
4 shared publicationsBeate Langer
University of Applied Sciences Merseburg Eberhard‐Leibnitz‐Straße 2 06127 Merseburg Germany
3 shared publicationsHai Hong Le
Leibniz‐Institut für Polymerforschung Dresden e.V. (IPF) Dresden Germany
3 shared publications- Sven Henning
Fraunhofer Institute for Microstructure of Materials and Systems (IMWS), Halle/Saale, Germany
3 shared publications
Latest Publications
- Open Access
- 22 October 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 45, 6191-6200
A novel method to obtain constitutive stiffness–plasticity relations from tensile tests employing the short-time Fourier transform
- 22 October 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 45, 6191-6200
Open AccessA novel method to obtain constitutive stiffness–plasticity relations from tensile tests employing the short-time Fourier transform
- Open Access
- 24 August 2026
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (11) , 8334-8343
Effect of Crystal Polymorphism on Elastic Modulus and Hardness of Poly(Butylene 2,6‐Naphthalate) (PBN)
The modulus of elasticity and hardness of poly(butylene 2,6‐naphthalate) (PBN) were investigated at different length scales using dynamic‐mechanical analysis (DMA), microhardness testing, and nanoindentation. By variation of the conditions of melt‐crystallization, PBN containing around 40% α‐crystals, β′‐crystals, or liquid crystals, beside glassy amorphous structure, was obtained. The absence of crystals and formation of liquid crystals, achieved by quenching the melt to ambient temperature, yield a material of relatively low stiffness and hardness of around 1/2 to 2/3 of PBN preparations containing crystals. The difference in modulus and hardness of PBN containing α‐ or β′‐crystals is minor, with slightly higher values observed for PBN composed of the amorphous glass and β′‐crystals. The higher values of the elastic modulus and hardness in case of presence of crystals are attributed to the higher packing density of molecular stems in the crystalline phase, compared to their rather loose packing within the layers of the smectic liquid crystals, besides the possible effect of the morphology and superstructure if plastic deformation is involved. The findings of this study provide important insight into structure–property relationships of polymorphic PBN and offer guidance for the design of this material for specific industrial applications.
- 24 August 2026
- Published by Wiley in Polymer Engineering & Science
- Vol. 66 (11) , 8334-8343
Open AccessEffect of Crystal Polymorphism on Elastic Modulus and Hardness of Poly(Butylene 2,6‐Naphthalate) (PBN)
The modulus of elasticity and hardness of poly(butylene 2,6‐naphthalate) (PBN) were investigated at different length scales using dynamic‐mechanical analysis (DMA), microhardness testing, and nanoindentation. By variation of the conditions of melt‐crystallization, PBN containing around 40% α‐crystals, β′‐crystals, or liquid crystals, beside glassy amorphous structure, was obtained. The absence of crystals and formation of liquid crystals, achieved by quenching the melt to ambient temperature, yield a material of relatively low stiffness and hardness of around 1/2 to 2/3 of PBN preparations containing crystals. The difference in modulus and hardness of PBN containing α‐ or β′‐crystals is minor, with slightly higher values observed for PBN composed of the amorphous glass and β′‐crystals. The higher values of the elastic modulus and hardness in case of presence of crystals are attributed to the higher packing density of molecular stems in the crystalline phase, compared to their rather loose packing within the layers of the smectic liquid crystals, besides the possible effect of the morphology and superstructure if plastic deformation is involved. The findings of this study provide important insight into structure–property relationships of polymorphic PBN and offer guidance for the design of this material for specific industrial applications.
- Open Access
- 1 July 2026
- Published by Nepal Journals Online (JOL) in Journal of Institute of Science and Technology
- Vol. 31 (1) , 331-350
NEXT GENERATION GREEN BIO-ADHESIVES AS RENEWABLE ALTERNATIVES TO SYNTHETIC PETRO-ADHESIVES
Growing environmental concerns associated with petroleum-based synthetic adhesives, including toxicity, non-renewability, volatile organic compound emissions, and formaldehyde-related health risks, have accelerated the development of sustainable bio-based adhesive systems. This review summarizes recent advances in adhesives derived from renewable resources such as lignin, tannins, proteins, polysaccharides, and vegetable oils. Particular emphasis is placed on adhesion mechanisms, chemical and enzymatic modification, nanotechnology-assisted reinforcement, and self-bonding approaches that can improve mechanical strength, thermal stability, and water resistance. Recent progress in green crosslinking strategies and biodegradable adhesive technologies has expanded the potential application range of bio-based adhesives in wood composites, packaging, construction, furniture, automotive components, and selected biomedical uses. Life cycle assessment studies indicate that bio-based adhesives can reduce fossil resource use, toxicity, and greenhouse gas emissions compared with conventional petrochemical systems; however, these benefits strongly depend on feedstock selection, processing route, formulation, energy demand, and end-of-life scenario. Despite substantial progress, challenges related to outdoor durability, water resistance, cost, raw-material variability, and large-scale commercialization remain significant. Overall, development in green chemistry, material engineering, and biomass valorization suggests that bio-based adhesives are promising candidates for next-generation bonding technologies, provided that their performance and sustainability are evaluated for each specific application.
- 1 July 2026
- Published by Nepal Journals Online (JOL) in Journal of Institute of Science and Technology
- Vol. 31 (1) , 331-350
Open AccessNEXT GENERATION GREEN BIO-ADHESIVES AS RENEWABLE ALTERNATIVES TO SYNTHETIC PETRO-ADHESIVES
Growing environmental concerns associated with petroleum-based synthetic adhesives, including toxicity, non-renewability, volatile organic compound emissions, and formaldehyde-related health risks, have accelerated the development of sustainable bio-based adhesive systems. This review summarizes recent advances in adhesives derived from renewable resources such as lignin, tannins, proteins, polysaccharides, and vegetable oils. Particular emphasis is placed on adhesion mechanisms, chemical and enzymatic modification, nanotechnology-assisted reinforcement, and self-bonding approaches that can improve mechanical strength, thermal stability, and water resistance. Recent progress in green crosslinking strategies and biodegradable adhesive technologies has expanded the potential application range of bio-based adhesives in wood composites, packaging, construction, furniture, automotive components, and selected biomedical uses. Life cycle assessment studies indicate that bio-based adhesives can reduce fossil resource use, toxicity, and greenhouse gas emissions compared with conventional petrochemical systems; however, these benefits strongly depend on feedstock selection, processing route, formulation, energy demand, and end-of-life scenario. Despite substantial progress, challenges related to outdoor durability, water resistance, cost, raw-material variability, and large-scale commercialization remain significant. Overall, development in green chemistry, material engineering, and biomass valorization suggests that bio-based adhesives are promising candidates for next-generation bonding technologies, provided that their performance and sustainability are evaluated for each specific application.
- Open Access
- 4 May 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (9) , 095303
Traditional Nepali paper-CNT-polyaniline hybrid as a green humidity sensor
This study reports a simple and cost-effective strategy to integrate in situ -polymerised polyaniline (PANI) and multi-walled carbon nanotubes (CNTs) into traditional Nepali paper (TNP) to fabricate cellulose-based electrically conductive composite films. The resulting films exhibited enhanced electrical conductivity, thermal stability and humidity-sensing performance. An interpenetrating spongy PANI network formed on the TNP surface enabled efficient charge transfer, while the incorporation of CNTs provided a synergistic effect, reducing the electrical resistivity to 6.4 Ω·cm at 0.05 wt.% CNTs. The sensing behaviour of PANI is governed by proton-transfer-assisted electron hopping between its protonated reduced (–NH 2 + ) and oxidized (–NH + ) forms, facilitated by water molecules under humid conditions, which lowers the composite’s resistivity. At higher humidity levels, the Grotthuss mechanism becomes dominant, further decreasing the resistance. In humidity-sensing tests, PANI-coated TNP without CNTs showed a pronounced relative resistance drop of ∼78%, reaching saturation after 90 s of exposure to saturated humidity. However, during dynamic cycling with short exposure and recovery times of 30 s each, its reversibility was limited, with a recovery factor of only 13.6% in the first cycle. In contrast, PANI-coated TNP with 0.01 wt.% CNTs showed a smaller relative resistance drop (∼47%) and reached saturation faster, after 70 s, but demonstrated improved reversibility, with a recovery factor of 46.1% in the first cycle of dynamic cycling tests. From the second cycle onward, both composites displayed excellent cycle-to-cycle stability with high reversibility. These findings underline the potential of TNP–PANI–CNT composites as sustainable and tunable sensing materials built on a potentially biodegradable substrate for greener electronic applications.
- 4 May 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (9) , 095303
Open AccessTraditional Nepali paper-CNT-polyaniline hybrid as a green humidity sensor
This study reports a simple and cost-effective strategy to integrate in situ -polymerised polyaniline (PANI) and multi-walled carbon nanotubes (CNTs) into traditional Nepali paper (TNP) to fabricate cellulose-based electrically conductive composite films. The resulting films exhibited enhanced electrical conductivity, thermal stability and humidity-sensing performance. An interpenetrating spongy PANI network formed on the TNP surface enabled efficient charge transfer, while the incorporation of CNTs provided a synergistic effect, reducing the electrical resistivity to 6.4 Ω·cm at 0.05 wt.% CNTs. The sensing behaviour of PANI is governed by proton-transfer-assisted electron hopping between its protonated reduced (–NH 2 + ) and oxidized (–NH + ) forms, facilitated by water molecules under humid conditions, which lowers the composite’s resistivity. At higher humidity levels, the Grotthuss mechanism becomes dominant, further decreasing the resistance. In humidity-sensing tests, PANI-coated TNP without CNTs showed a pronounced relative resistance drop of ∼78%, reaching saturation after 90 s of exposure to saturated humidity. However, during dynamic cycling with short exposure and recovery times of 30 s each, its reversibility was limited, with a recovery factor of only 13.6% in the first cycle. In contrast, PANI-coated TNP with 0.01 wt.% CNTs showed a smaller relative resistance drop (∼47%) and reached saturation faster, after 70 s, but demonstrated improved reversibility, with a recovery factor of 46.1% in the first cycle of dynamic cycling tests. From the second cycle onward, both composites displayed excellent cycle-to-cycle stability with high reversibility. These findings underline the potential of TNP–PANI–CNT composites as sustainable and tunable sensing materials built on a potentially biodegradable substrate for greener electronic applications.
- Open Access
- 4 November 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (48) , 35715-35726
Piezoresistivity and strain-sensing behaviour of poly(butylene adipate-co-terephthalate)/multiwalled carbon nanotube nanocomposites
The interconnectedness of the exfoliated multi-walled carbon nanotubes well dispersed in the PBAT matrix (TEM image; left) leads to strain-sensing properties at lower strains as illustrated by the variation of ΔR/R0 as a function of mechanical strain with time (right).
- 4 November 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (48) , 35715-35726
Open AccessPiezoresistivity and strain-sensing behaviour of poly(butylene adipate-co-terephthalate)/multiwalled carbon nanotube nanocomposites
The interconnectedness of the exfoliated multi-walled carbon nanotubes well dispersed in the PBAT matrix (TEM image; left) leads to strain-sensing properties at lower strains as illustrated by the variation of ΔR/R0 as a function of mechanical strain with time (right).
- Open Access
Fracture Toughness, Radiation Hardness, and Processibility of Polymers for Superconducting Magnets
High fracture toughness at cryogenic temperature and radiation hardness can be conflicting requirements for the resins for the impregnation of superconducting magnet coils. The fracture toughness of different epoxy-resin systems at room temperature (RT) and at 77 K was measured, and their toughness was compared with that determined for a polyurethane, polycarbonate (PC) and poly(methyl methacrylate) (PMMA). Among the epoxy resins tested in this study, the MY750 system has the highest 77 K fracture toughness of KIC = 4.6 MPa√m, which is comparable to the KIC of PMMA, which also exhibits linear elastic behaviour and unstable crack propagation. The polyurethane system tested has a much higher 77 K toughness than the epoxy resins, approaching the toughness of PC, which is known as one of the toughest polymer materials. CTD101K is the least performing in terms of fracture toughness. Despite this, it is used for the impregnation of large Nb3Sn coils for its good processing capabilities and relatively high radiation resistance. In this study, the fracture toughness of CTD101K was improved by adding the polyglycol flexibiliser Araldite DY040 as a fourth component. The different epoxy-resin systems were exposed to proton and gamma doses up to 38 MGy, and it was found that adding the DY040 flexibiliser to the CTD101K system did not significantly change the irradiation-induced ageing behaviour. The viscosity evolution of the uncured resin mix is not significantly changed when adding the DY040 flexibiliser, and at the processing temperature of 60 °C, the viscosity remains below 200 cP for more than 24 h. Therefore, the new resin referred to as POLAB Mix is now used for the impregnation of superconducting magnet coils.
Open AccessFracture Toughness, Radiation Hardness, and Processibility of Polymers for Superconducting Magnets
High fracture toughness at cryogenic temperature and radiation hardness can be conflicting requirements for the resins for the impregnation of superconducting magnet coils. The fracture toughness of different epoxy-resin systems at room temperature (RT) and at 77 K was measured, and their toughness was compared with that determined for a polyurethane, polycarbonate (PC) and poly(methyl methacrylate) (PMMA). Among the epoxy resins tested in this study, the MY750 system has the highest 77 K fracture toughness of KIC = 4.6 MPa√m, which is comparable to the KIC of PMMA, which also exhibits linear elastic behaviour and unstable crack propagation. The polyurethane system tested has a much higher 77 K toughness than the epoxy resins, approaching the toughness of PC, which is known as one of the toughest polymer materials. CTD101K is the least performing in terms of fracture toughness. Despite this, it is used for the impregnation of large Nb3Sn coils for its good processing capabilities and relatively high radiation resistance. In this study, the fracture toughness of CTD101K was improved by adding the polyglycol flexibiliser Araldite DY040 as a fourth component. The different epoxy-resin systems were exposed to proton and gamma doses up to 38 MGy, and it was found that adding the DY040 flexibiliser to the CTD101K system did not significantly change the irradiation-induced ageing behaviour. The viscosity evolution of the uncured resin mix is not significantly changed when adding the DY040 flexibiliser, and at the processing temperature of 60 °C, the viscosity remains below 200 cP for more than 24 h. Therefore, the new resin referred to as POLAB Mix is now used for the impregnation of superconducting magnet coils.
- 31 December 2023
- Published by Wiley in Polymer Composites
- Vol. 45 (5) , 4295-4306
Rapid assessment of wetting of natural fiber surfaces by biodegradable copolyester using spectroscopic and microscopic techniques
A biodegradable polymer, the poly(butylene adipate co‐terephthalate) (PBAT), was compounded with the microcrystalline cellulose (MCC) obtained from different sources (such as wheat stalk and rice husk powder) to prepare the polymer composites. The two components, here found to be compatible, as evidenced by the Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). Further assessment of the compounded fibers with the organic solvent, the toluene, illustrated the nature of the wetting phenomena of MCC by PBAT. The SEM observation showed the wrapping of the PBAT layer onto the MCC phase after the removal of the polymer matrix. The FTIR spectrum showed the presence of the PBAT carbonyl peak on extracted fibers from the composite via solvent removal. It could be concluded that the PBAT could wet the MCC effectively in the composites suggesting the potential of enhancing their properties.Highlights: A biodegradable polymer, the PBAT, melt‐mixed with plant‐based natural fiber. The fiber in composites was found to be wetted with the PBAT layer. H‐bonding between the CO group of PBAT and the OH group of fiber caused wetting. Raw, processed, and silane‐treated fibers showed similar wetting phenomena.
- 31 December 2023
- Published by Wiley in Polymer Composites
- Vol. 45 (5) , 4295-4306
Rapid assessment of wetting of natural fiber surfaces by biodegradable copolyester using spectroscopic and microscopic techniques
A biodegradable polymer, the poly(butylene adipate co‐terephthalate) (PBAT), was compounded with the microcrystalline cellulose (MCC) obtained from different sources (such as wheat stalk and rice husk powder) to prepare the polymer composites. The two components, here found to be compatible, as evidenced by the Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). Further assessment of the compounded fibers with the organic solvent, the toluene, illustrated the nature of the wetting phenomena of MCC by PBAT. The SEM observation showed the wrapping of the PBAT layer onto the MCC phase after the removal of the polymer matrix. The FTIR spectrum showed the presence of the PBAT carbonyl peak on extracted fibers from the composite via solvent removal. It could be concluded that the PBAT could wet the MCC effectively in the composites suggesting the potential of enhancing their properties.Highlights: A biodegradable polymer, the PBAT, melt‐mixed with plant‐based natural fiber. The fiber in composites was found to be wetted with the PBAT layer. H‐bonding between the CO group of PBAT and the OH group of fiber caused wetting. Raw, processed, and silane‐treated fibers showed similar wetting phenomena.
- 9 August 2022
- Published by Springer Nature in Polymer Bulletin
- Vol. 80 (7) , 7599-7625
Influence of wheat stalk nanocellulose on structural, mechanical, thermal, surface and degradation properties of composites with poly(butylene adipate-co-terephthalate)
- 9 August 2022
- Published by Springer Nature in Polymer Bulletin
- Vol. 80 (7) , 7599-7625
Influence of wheat stalk nanocellulose on structural, mechanical, thermal, surface and degradation properties of composites with poly(butylene adipate-co-terephthalate)
- 19 June 2022
- Published by Wiley in Macromolecular Symposia
- Vol. 403 (1)
Morphology, Deformation, and Micromechanical Behavior of Electrospun Nano‐hydroxyapatite Blended Biohybrid Scaffolds
For bone tissue engineering, nano‐hydroxyapatite (nano‐HAp) is a widely used bioceramic filler in polymer fibrous scaffolds that changes the morphology and micromechanical behavior of fibers. In this study, different volume fraction percentages of nano‐HAp and vitamin D3 (VD3) are incorporated into electrospun polymer blend fibrous scaffolds comprising polycaprolactone (PCL), poly‐L‐lactic acid (PLLA), and gelatin (GEL). Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and uniaxial tensile testing are used to characterize the chemical, morphological, and micromechanical properties of the scaffolds. The FTIR analysis showed the presence of functional groups of fillers and polymers and their molecular interactions in the fibers. In the microscopic analysis, the fillers are found to affect the fiber morphology (including diameter, phase separation, and texture) and the response of the fibers under tensile deformation. The addition of 3% by volume of filler suspension results in maximum diameter of 4.34 µm, and the addition of 6%–12% filler leads to an increase in tensile strength from 0.7 to 5.6 MPa and strain at break from 2% to 37% for the composite fibers compared to neat fibers. The crazing behavior of the fiber is more noticeable at a low filler content (0%), whereas thin‐layer yielding becomes predominant at a higher filler content (12%). Thus, the study shows that scaffold fibers undergo brittle‐to‐ductile transitions as the filler percentage in the polymer blend increases from 0% to 12%. It has been further found that morphogens used as growth factors can be easily released from hydroxyapatite after adsorption.
- 19 June 2022
- Published by Wiley in Macromolecular Symposia
- Vol. 403 (1)
Morphology, Deformation, and Micromechanical Behavior of Electrospun Nano‐hydroxyapatite Blended Biohybrid Scaffolds
For bone tissue engineering, nano‐hydroxyapatite (nano‐HAp) is a widely used bioceramic filler in polymer fibrous scaffolds that changes the morphology and micromechanical behavior of fibers. In this study, different volume fraction percentages of nano‐HAp and vitamin D3 (VD3) are incorporated into electrospun polymer blend fibrous scaffolds comprising polycaprolactone (PCL), poly‐L‐lactic acid (PLLA), and gelatin (GEL). Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and uniaxial tensile testing are used to characterize the chemical, morphological, and micromechanical properties of the scaffolds. The FTIR analysis showed the presence of functional groups of fillers and polymers and their molecular interactions in the fibers. In the microscopic analysis, the fillers are found to affect the fiber morphology (including diameter, phase separation, and texture) and the response of the fibers under tensile deformation. The addition of 3% by volume of filler suspension results in maximum diameter of 4.34 µm, and the addition of 6%–12% filler leads to an increase in tensile strength from 0.7 to 5.6 MPa and strain at break from 2% to 37% for the composite fibers compared to neat fibers. The crazing behavior of the fiber is more noticeable at a low filler content (0%), whereas thin‐layer yielding becomes predominant at a higher filler content (12%). Thus, the study shows that scaffold fibers undergo brittle‐to‐ductile transitions as the filler percentage in the polymer blend increases from 0% to 12%. It has been further found that morphogens used as growth factors can be easily released from hydroxyapatite after adsorption.
- Open Access
- 19 June 2022
- Published by Wiley in Macromolecular Symposia
- Vol. 403 (1)
Influence of Media–Thermal Ageing on the Long‐Term Creep Behavior of Polypropylene
Plastic components subjected to a constant load, such as pipes or load‐bearing structures in motor vehicles, tend to creep and show increased deformation over time. In special applications for example coolant expansion tanks, increased temperatures and media also affect the long‐term creep behavior. In this study, the influence of media–thermal aging on the long‐term creep behavior is investigated for predicting service life.
- 19 June 2022
- Published by Wiley in Macromolecular Symposia
- Vol. 403 (1)
Open AccessInfluence of Media–Thermal Ageing on the Long‐Term Creep Behavior of Polypropylene
Plastic components subjected to a constant load, such as pipes or load‐bearing structures in motor vehicles, tend to creep and show increased deformation over time. In special applications for example coolant expansion tanks, increased temperatures and media also affect the long‐term creep behavior. In this study, the influence of media–thermal aging on the long‐term creep behavior is investigated for predicting service life.