Adam Wosatko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Adam Wosatko has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Jerzy Pamin
Chair for Computational Engineering, Faculty of Civil Engineering, Cracow University of Technology, Warszawska 24, 31-155 Cracow, Poland
8 shared publications - Andrzej Winnicki
Asst. Prof. of Civ. Engrg., Cracow Univ. of Technol., Cracow 31-155, 24 Warszawska St., Poland
4 shared publications Maria Anna Polak
3 shared publicationsAndrzej Winnicki
2 shared publicationsJerzy Pamin
2 shared publicationsAikaterini Genikomsou
1 shared publication
Latest Publications
- 10 June 2025
- Published by Index Copernicus in Przegląd Budowlany
- Vol. 96 (3) , 56-58
Inżynieria obliczeniowa – Katedra TechnologiiInformatycznych w Inżynierii L-10
Celem artykułu jest zapoznanie czytelników z kierunkamiprac naukowych prowadzonych w Katedrze TechnologiiInformatycznych w Inżynierii. Nasze prace dotyczą rozwijaniazaawansowanych modeli zjawisk i procesów oraz efektywnychi oryginalnych metod obliczeniowych
- 10 June 2025
- Published by Index Copernicus in Przegląd Budowlany
- Vol. 96 (3) , 56-58
Inżynieria obliczeniowa – Katedra TechnologiiInformatycznych w Inżynierii L-10
Celem artykułu jest zapoznanie czytelników z kierunkamiprac naukowych prowadzonych w Katedrze TechnologiiInformatycznych w Inżynierii. Nasze prace dotyczą rozwijaniazaawansowanych modeli zjawisk i procesów oraz efektywnychi oryginalnych metod obliczeniowych
- Open Access
- 11 March 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (6) , 3051
Comparative Analysis of In-Plane and Out-of-Plane Bending Benchmarks Using Two Finite Element Packages
An essential aspect of design from the perspective of structural strength is the reliability of the results obtained during the computations for the analyzed model. Among various skills in numerical analysis, an engineer should be able to independently verify the quality of the available software using benchmarks already at the level of statics. An effective method of such verification is comparing the test results obtained from two different packages. The paper discusses three structure-oriented benchmarks for in-plane and out-of-plane bending of a flat membrane and a slab, respectively. The computations are carried out using the Robot and Midas finite element tools. These simulation tests are selected to present issues related to the modeling of bending, which is crucial for reliable design: the convergence of the solution for a cantilever, the possibility of a reduction in slab moments above columns, and the interaction effects between the beam and the plate, depending on their position and connection in the model. It is shown that, in finite element calculations, attention must be paid to avoiding errors due to improper data input and software option settings, leading to incorrect simulation results, which may negatively impact the design process. A proper understanding of software tools, for example, through benchmark verification, ensures their conscious use in developing more complex structural models.
- 11 March 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (6) , 3051
Open AccessComparative Analysis of In-Plane and Out-of-Plane Bending Benchmarks Using Two Finite Element Packages
An essential aspect of design from the perspective of structural strength is the reliability of the results obtained during the computations for the analyzed model. Among various skills in numerical analysis, an engineer should be able to independently verify the quality of the available software using benchmarks already at the level of statics. An effective method of such verification is comparing the test results obtained from two different packages. The paper discusses three structure-oriented benchmarks for in-plane and out-of-plane bending of a flat membrane and a slab, respectively. The computations are carried out using the Robot and Midas finite element tools. These simulation tests are selected to present issues related to the modeling of bending, which is crucial for reliable design: the convergence of the solution for a cantilever, the possibility of a reduction in slab moments above columns, and the interaction effects between the beam and the plate, depending on their position and connection in the model. It is shown that, in finite element calculations, attention must be paid to avoiding errors due to improper data input and software option settings, leading to incorrect simulation results, which may negatively impact the design process. A proper understanding of software tools, for example, through benchmark verification, ensures their conscious use in developing more complex structural models.
- Open Access
- 18 February 2024
- Published by Polish Society of Theoretical and Applied Mechanics in Journal of Theoretical and Applied Mechanics
- Vol. 62 (2) , 193-206
Ability of localizing gradient damage to determine size effect in concrete beams
The objective of the paper is to demonstrate the potential of the localizing gradient dam- age model in size effect simulations. Three different gradient activity functions for variable internal length scale are considered. Numerical simulations for an unnotched beam under three-point bending are...
- 18 February 2024
- Published by Polish Society of Theoretical and Applied Mechanics in Journal of Theoretical and Applied Mechanics
- Vol. 62 (2) , 193-206
Open AccessAbility of localizing gradient damage to determine size effect in concrete beams
The objective of the paper is to demonstrate the potential of the localizing gradient dam- age model in size effect simulations. Three different gradient activity functions for variable internal length scale are considered. Numerical simulations for an unnotched beam under three-point bending are...
- Open Access
Survey of Localizing Gradient Damage in Static and Dynamic Tension of Concrete
The continuum damage model should be regularized to ensure mesh-insensitive results in simulations of strain localization, e.g., for concrete cracking under tension. The paper confronts the conventional gradient damage model with its upgrade including a variable internal length scale. In these models, the Helmholtz free energy depends additionally on an averaged strain measure and its gradient. In the formulation for dynamics the equations of motion are discretized simultaneously with an averaging equation. If gradient regularization is employed with a constant internal length parameter, then an artificially expanded damage zone can occur in the strain softening analysis. This broadening effect can be inhibited by a gradient activity function. The localizing character of the gradient activity has physical motivation—the nonlocal interactions in the fracture zone are reduced with the damage growth. The internal length can decrease exponentially or as a cosine function. After presentation of the theory, including the free energy definition, the finite element analyses of three different examples connected with tensile cracking in concrete are discussed: static tension of a double-edge-notched specimen, dynamic direct tension for a configuration without or with a reinforcing bar and tension of an L-shaped specimen under static and dynamic loading.
Open AccessSurvey of Localizing Gradient Damage in Static and Dynamic Tension of Concrete
The continuum damage model should be regularized to ensure mesh-insensitive results in simulations of strain localization, e.g., for concrete cracking under tension. The paper confronts the conventional gradient damage model with its upgrade including a variable internal length scale. In these models, the Helmholtz free energy depends additionally on an averaged strain measure and its gradient. In the formulation for dynamics the equations of motion are discretized simultaneously with an averaging equation. If gradient regularization is employed with a constant internal length parameter, then an artificially expanded damage zone can occur in the strain softening analysis. This broadening effect can be inhibited by a gradient activity function. The localizing character of the gradient activity has physical motivation—the nonlocal interactions in the fracture zone are reduced with the damage growth. The internal length can decrease exponentially or as a cosine function. After presentation of the theory, including the free energy definition, the finite element analyses of three different examples connected with tensile cracking in concrete are discussed: static tension of a double-edge-notched specimen, dynamic direct tension for a configuration without or with a reinforcing bar and tension of an L-shaped specimen under static and dynamic loading.
- Open Access
- 29 October 2021
- Published by Politechnika Lubelska in Budownictwo i Architektura
- Vol. 20 (3) , 005-024
Effectivity of BIM transfer of structural models between programs for engineers
The paper describes the verification of the quality of the data transfer between selected software dedicated to generation of building models and for their analysis using the finite element method. For comparison, models of two typical structures are constructed: a steel truss hall and a multi-storey reinforced concrete building. Both models are created simultaneously in two programs: Autodesk Revit and Tekla Structures. Next, these models are exported to computational packages: Autodesk Robot, Dlubal RFEM and SCIA Engineer. Different options of data transfer are considered, in particular: a direct link between programs as well as via open formats. The scope and limitations of the data exchange are determined in each case. Juxtaposition of the effectiveness of different transfer methods for such typical building models are helpful at the stage of cooperation between the architect and the structural designer. In addition, pilot results of a finite element static analysis for the steel hall model are also compared.
- 29 October 2021
- Published by Politechnika Lubelska in Budownictwo i Architektura
- Vol. 20 (3) , 005-024
Open AccessEffectivity of BIM transfer of structural models between programs for engineers
The paper describes the verification of the quality of the data transfer between selected software dedicated to generation of building models and for their analysis using the finite element method. For comparison, models of two typical structures are constructed: a steel truss hall and a multi-storey reinforced concrete building. Both models are created simultaneously in two programs: Autodesk Revit and Tekla Structures. Next, these models are exported to computational packages: Autodesk Robot, Dlubal RFEM and SCIA Engineer. Different options of data transfer are considered, in particular: a direct link between programs as well as via open formats. The scope and limitations of the data exchange are determined in each case. Juxtaposition of the effectiveness of different transfer methods for such typical building models are helpful at the stage of cooperation between the architect and the structural designer. In addition, pilot results of a finite element static analysis for the steel hall model are also compared.
- Open Access
- 16 February 2021
- Published by Springer Nature in Archive of Applied Mechanics
- Vol. 91 (2) , 597-627
Comparison of evolving gradient damage formulations with different activity functions
In the paper, two existing upgrades of the gradient damage model for the simulations of cracking in concrete are compared. The damage theory is made nonlocal via a gradient enhancement to overcome the mesh dependence of simulation results. The implicit gradient model with an averaging equation, where the internal length parameter is assumed as constant during the strain softening analysis, gives unrealistically broadened damage zones. The gradient enhancement of the scalar damage model can be improved via a function of an internal length scale, so an evolution of the gradient activity is postulated during the localization process. Two different modifications of the averaging equation and respective evolving gradient damage formulations are presented. Different activity functions are tested to see whether the formation of a too wide damage zone still occurs. Activating or localizing character of the gradient influence can be introduced and the impact of both approaches on the numerical results is shown in the paper. The aforementioned variants are implemented and examined using the benchmarks of tension in a bar and bending of a cantilever beam.
- 16 February 2021
- Published by Springer Nature in Archive of Applied Mechanics
- Vol. 91 (2) , 597-627
Open AccessComparison of evolving gradient damage formulations with different activity functions
In the paper, two existing upgrades of the gradient damage model for the simulations of cracking in concrete are compared. The damage theory is made nonlocal via a gradient enhancement to overcome the mesh dependence of simulation results. The implicit gradient model with an averaging equation, where the internal length parameter is assumed as constant during the strain softening analysis, gives unrealistically broadened damage zones. The gradient enhancement of the scalar damage model can be improved via a function of an internal length scale, so an evolution of the gradient activity is postulated during the localization process. Two different modifications of the averaging equation and respective evolving gradient damage formulations are presented. Different activity functions are tested to see whether the formation of a too wide damage zone still occurs. Activating or localizing character of the gradient influence can be introduced and the impact of both approaches on the numerical results is shown in the paper. The aforementioned variants are implemented and examined using the benchmarks of tension in a bar and bending of a cantilever beam.
- Open Access
Selected Concrete Models Studied Using Willam’s Test
Willam’s test is a quick numerical benchmark in tension–shear regime, which can be used to verify inelastic (quasi-brittle) material models at the point level. Its sequence consists of two separate steps: uniaxial tension accompanied with contraction—until the tensile strength is attained; and next for softening (cracking) of the material—tension in two directions together with shear. A rotation of axes of principal strains and principal stresses is provoked in the second stage. That kind of process occurs during the analysis of real concrete structures, so a correct response of the material model at the point level is needed. Some familiar concrete models are selected to perform Willam’s test in the paper: concrete damaged plasticity and concrete smeared cracking—distributed in the commercial ABAQUS software, scalar damage with coupling to plasticity and isotropic damage—both implemented in the FEAP package. After a brief review of the theory, computations for each model are discussed. Passing or failing Willam’s test by the above models is concluded based on their results, indicating restrictions of their use for finite element computations of concrete structures with predominant mixed-mode fracture.
Open AccessSelected Concrete Models Studied Using Willam’s Test
Willam’s test is a quick numerical benchmark in tension–shear regime, which can be used to verify inelastic (quasi-brittle) material models at the point level. Its sequence consists of two separate steps: uniaxial tension accompanied with contraction—until the tensile strength is attained; and next for softening (cracking) of the material—tension in two directions together with shear. A rotation of axes of principal strains and principal stresses is provoked in the second stage. That kind of process occurs during the analysis of real concrete structures, so a correct response of the material model at the point level is needed. Some familiar concrete models are selected to perform Willam’s test in the paper: concrete damaged plasticity and concrete smeared cracking—distributed in the commercial ABAQUS software, scalar damage with coupling to plasticity and isotropic damage—both implemented in the FEAP package. After a brief review of the theory, computations for each model are discussed. Passing or failing Willam’s test by the above models is concluded based on their results, indicating restrictions of their use for finite element computations of concrete structures with predominant mixed-mode fracture.
- 1 August 2019
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 19 (4) , 1268-1283
Role of dilatancy angle in plasticity-based models of concrete
- 1 August 2019
- Published by Springer Nature in Archives of Civil and Mechanical Engineering
- Vol. 19 (4) , 1268-1283
Role of dilatancy angle in plasticity-based models of concrete
- 1 May 2018
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 194, 190-211
Examination of two regularized damage-plasticity models for concrete with regard to crack closing
- 1 May 2018
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 194, 190-211
Examination of two regularized damage-plasticity models for concrete with regard to crack closing
- Open Access
- 31 January 2018
- Published by Taylor & Francis
- p. 447-456
Numerical prediction of deterministic size effect in concrete bars and beams
The paper presents the results of simulations of deterministic size effect in concrete bars and beams. Two established material models are employed in the study: the consistency viscoplasticity and the gradient damage model. For direct tension of a double-edge notched bar three sizes are considered. For three-point bending of a beam without a notch four sizes are examined and the response is compared with experimental results taken from a paper by Grégoire et al. The results confirm that the regularized models exhibit size effect not only in the post-peak regime, but also in the nominal strength. It is more pronounced for the gradient damage model.
- 31 January 2018
- Published by Taylor & Francis
- p. 447-456
Open AccessNumerical prediction of deterministic size effect in concrete bars and beams
The paper presents the results of simulations of deterministic size effect in concrete bars and beams. Two established material models are employed in the study: the consistency viscoplasticity and the gradient damage model. For direct tension of a double-edge notched bar three sizes are considered. For three-point bending of a beam without a notch four sizes are examined and the response is compared with experimental results taken from a paper by Grégoire et al. The results confirm that the regularized models exhibit size effect not only in the post-peak regime, but also in the nominal strength. It is more pronounced for the gradient damage model.