Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Emad E. Etman has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Time-cost-quality tradeoff considering resource-scheduling problems

    by Ali F. Elkliny, Haytham M. Sanad, Emad E. Etman


  • Open Access

    Consolidation Effect on the Behavior of Micropiled Rafts Under Combined Loading: Case Study

    by Ahmed Elsawwaf, Mostafa El Sawwaf, Ashraf Nazir, Waseim Azzam, Ahmed Farouk, Emad Etman

    This paper used finite element modeling to evaluate the consolidation effect on the performance of existing rafts underpinned with micropiles under combined vertical and lateral loads. For this purpose, a real-life case study was discussed, in which micropile underpinning was used to stop the continuous tilt of a 13-floor residential building supported by a surface raft. It was found that the building tilted towards the northeast direction because of the consolidation of a deep soft clay layer under the northeast building corner. After discussing the as-built micropiling system, a 3D numerical model, developed using the PLAXIS software, was used to conduct the numerical research. The time-dependent behavior of the raft with and without the consideration of micropiles was assessed. Moreover, the variation of load-sharing ratios with time was investigated. The numerical results emphasize that the underpinning process was effective and reduced the final raft rotation and maximum settlement by 79.9% and 73.9%, respectively, compared to the case of the absence of micropiles. The consolidation process under a steady level of vertical loads enhanced the performance of the micropiled and unmicropiled rafts against upcoming lateral loads. The vertical load-sharing ratio increased during a life span of 20 years by 10.4% due to the consolidation process, but the increase was at a decreasing rate. Comparing all the four directions in which the lateral load was applied, the micropiles carried (57.4–76.6%) of the lateral load.


  • Flexural behaviour of concrete beams reinforced with steel-FRP composite bars

    by Emad E. Etman, Mohamed H. Mahmoud, Ali Hassan


  • Open Access

    Behavior of RC Beams with Circular Openings reinforced with Strain-Hardening Cementitious Composites (SHCC)

    by Emad E. Etman, Ahmed Baraghith, Reda Behiry, Aya Mansour

    In this paper, the effect of using Strain-Hardening Cementitious Composites (SHCC) to improve the shear behavior of reinforced concrete (RC) beams with web openings was experimentally investigated. A four-point bending test was performed on seven specimens. One of them, control beam BC , had no web opening, but the other six specimens were tested with web opening . The studied parameters were the effect of employing either plain or reinforced prefabricated SHCC and the influence of prefabricated SHCC configurations around web openings. On the basis of cracking patterns, load-deflection behavior, ductility, and initial stiffness, the shear behavior was evaluated. According to experimental findings, the presence of a web circular opening in the shear zone decreased the shear strength by about 46%. Nevertheless, the use of prefabricated SHCC shapes enhanced the shear strength of the tested specimens by up to 60% relative to the control specimen (BC-C). As soon as reinforcements were added to prefabricated SHCC, it was abundantly clear that the ultimate load and cracking behavior of RC beams with openings had improved.


  • Shear Strength of Fiber Reinforced Concrete Beams Made of Recycle Aggregate

    by Emad E. Etman, Hamdy Afefy, Ahmed Baraghit, Sara Khedr

    This paper presents the findings of an experimental program conducted in order to investigate the shear behavior of fiber reinforced concrete beams made of recycled aggregate. The studied parameters were the replacement ratio of the recycled aggregate (15, 30 and 45%) and the fiber volumetric ratio (1, 1.5 and 2%). Thus, a total of six simply supported recycled concrete beams along with one control conventional beam, with shear span-to-depth ratio of 2, were prepared and tested under incremental static loading. The studied criteria were the mid-span deflection, crack pattern, failure mode and shear strength. It was noticed that the crack patterns of all beams having recycled aggregate were similar to that for conventional concrete beam. Furthermore, at the same loading level, it was observed that the mid-span deflection increased when replacement ratio of recycled aggregate increased. It could be concluded that the shear strength decreased when the replacement ratio of recycled aggregate increased, however, the shear strength increased with increasing the fiber volumetric ratio.

  • ANALYSIS OF EXTERNALLY PRESTRESSED SEGMENTAL BOX GIRDERS UNDER BENDING, SHEAR, AND TORSION

    by Emad E. Etman, Abdelhakeem Khalil, Tarek El-Shafey, Mohamed Hussein, Mahmoud Abdelaziz

    Analysis of Externally Prestressed Segmental Bridges (EPSBs) still needs more effort. At an earlier stage, an experimental investigation was carried out by the authors. The experimental investigation was consisted of ten specimens having different joint configurations, and it was divided into two phases. The first phase contains five specimens constructed with multiple small-amplitude shear keys in accordance with AASHTO. The parameters selected for the first phase were different levels of prestressing force in tendons as well as different levels of applied torsion. The second phase contained four segmental specimens and a monolithic one. The joints in the second phase took four forms: multiple small-amplitude shear keys, large-reinforced shear key, steel shear connectors, and UHP–SHCC joint connecting the tension flange. This paper proposed an analytical procedure to calculate the full prestressing load and partial prestressing load based on the forces’ equilibrium. Skew Bending Model that inspected by Huan and Liu, 2006, to calculate the load-carrying capacity for segmental beams with internal unbonded tendons subjected to combined bending, shear, and torsion modified to calculate the ultimate capacity of EPSBs and gave satisfactory agreement with the experimental results.

  • Open Access

    Modeling of CPM/LOB integrated Scheduling Technique for Repetitive Construction Projects: Case of Multiple-Crews with Fuzzy Time Data

    by Mai W. El-Nawawy, Emad Etman, Haytham M. Sanad

    Project scheduling provides a good insight for the manager to complete the project on time. Project scheduling gives complete timing analysis of activities involved and identifies the critical ones. Critical Path Method (CPM) is the most widely used in planning and scheduling method for traditional (non-repetitive) projects to determine the critical path which determines the minimum completion time of a project.Some construction projects consist of several similar or identical units, which are called repetitive projects. LOB technique has some drawbacks such inability to generate a clear critical path of the project schedule and calculating the total float because it is a graphical technique. LOB used for scheduling repetitive typical projects because this technique considered work continuity and resource availability constraints to avoid unnecessary crew idle time.Some of the previous studies have been made to combine the benefits of CPM and LOB techniques in planning and scheduling repetitive construction projects, so, there is a model that was developed for this objective (schedule repetitive projects in an easy non-graphical manner). But, in real life, more conditions contributed to varying activity duration. Thus, the duration of project activities contains some sort of uncertainty affecting the estimating of project duration. Previous studies used fuzzy set theory instead of probability theory for quantifying the uncertainty associated with the duration of project activities.In this paper, a developed integrated model of CPM and LOB with fuzzy time data for scheduling repetitive projects is presented. The developed model provides a new technique to schedule repetitive projects with fuzzy time data in an easy non-graphical manner.


  • Open Access

    FLEXURAL BEHAVIOUR OF CONCRETE BEAMS REINFORCED WITH BASALT FRP BAR

    by Emad E Etman, Mohamed H Mahmoud, Ahmed T Baraghith, Ahmed A Elsheikh

    The flexural properties of six 150 x 300 x2400 mm concrete beams reinforced with basalt FRP(BFRP) bars were investigated. The beams were divided into two groups , the first groupconsisted of four beams reinforced with only BFRP bars with reinforcement ratio (ρf) rangedfrom 3.59 to 8.95 times the balanced ratio (ρfb ) according to ACI 440.1R-06 . The secondgroup consisted of two hybrid beams reinforced with BFRP and steel bars with ρf 3.59 and 5.38times ρfb in addition to one steel bar of diameter 10mm and yield strength 360 MPa . Thebeams were tested under four-point bending over a clear span of 2200 mm until failure. The testresults of the first group indicated that when ρf increased by 150% , the ultimate deflection wasreduced by 50% and ultimate load capacity was increased by 40% compared with the beam thathad ( ρf = 3.59 ρfb ) . The mode of failure of the first group beams is concrete crushing in thetop compression fiber. The test results of the beams of the second group indicated that addingsteel bar of diameter 10mm to the beam that had two BFRP bars (by steel to BFRPreinforcement ratio =35%), led to reducing the ultimate deflection by 42 % while the ultimateload capacity increased by 10%. Moreover , adding steel bar of diameter 10mm to the beamthat had three BFRP bars (by steel to BFRP reinforcement ratio =25%), led to reducing theultimate deflection by 30 % while the ultimate load capacity increased by 8% . This shows thatthere is a direct relation between steel to BFRP reinforcement ratio and the reduction ofdeflection and the effect of adding steel bar is more pronounced on reducing ultimate deflectionthan increasing ultimate load capacity and hence enhancing serviceability of the beams

  • Open Access

    Optimizing Cash Flow of Construction Projects through Different Bid Pricing Schemes

    by Mohamed M. Gaber, Emad E. Etman, Haytham M. Sanad, Mohamed M. Marzouk

    Successful construction projects should meet the planning and design objectives within budget and time constraints. Planning and scheduling for the construction projects and their resources are essential tasks for overall project success. Cash, in particular, is an important resource for construction companies. It is worth noting that while pricing bill of quantities in unit price contracts, the contractor might ignore the related cash flow which may be insufficient for contractor. Further, the resulted financial threats also might be ignored. Therefore, it is important for the contractor to have an overall optimized system to improve all financial aspects related to the contract. This paper presents a cash flow optimization model that aims at maximizing cumulative concurrent investment profit (CCIP) and minimizing maximum monthly overdrafts (OMax). The model utilizes Genetic Algorithms for optimization. The performance of the developed model is validated using an actual case study of "Beni Suef Power Station Project" located in Beni Suef, Egypt.


  • Open Access

    EFFICIENT STEEL-REINFORCED UHP-SHCC STRENGTHENING FOR LAP-SPLICED RC BEAMS

    by Emad E Etman, Ahmed M Atta, Ahmed T Baraghith, Asmaa F Edris

    This paper investigates the effectiveness of strengthening reinforced concrete (RC) beams with tension lap splices using a jacketing of Ultra High Performance Strain Hardening Cementitious Composites (UHP-SHCC) with embedded vertical stirrups. Nine RC specimens with different lap splice lengths at the mid span region were tested in flexure to examine the performance of the proposed technique for eliminating the bond failure mode in such lap splices. The test parameters were the lap splice length and the effect of confinement (no confinement and a jacketing of UHP-SHCC with embedded stirrups at different spacing). The test results show that, whilst the spliced control specimens failed in a brittle manner due to splitting of main steel, using UHP-SHCC jacketing with embedded vertical stirrups has increased the ultimate load and changed the mode of failure to flexural and ductile one. Moreover, a pronounced effect on increasing the bond strength between the reinforcing steel bars and surrounding concrete was observed for all confined specimens. Consequently, a satisfactory ductility was obtained which confirms the applicability of the UHP-SHCC jacketing for strengthening lap-spliced region of RC beams.