Nathan Canfield
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Nathan Canfield has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Aashish Rohatgi
Pacific Northwest National Laboratory
1 shared publication - Adam Denny
Pacific Northwest National Laboratory
1 shared publication - Amanda R. Lawter
Pacific Northwest National Laboratory
1 shared publication Christopher Coyle
Pacific Northwest National Laboratory, Applied Materials and Manufacturing Group, Richland WA, USA
1 shared publication- Erin M. McElroy
Energy and Environment Directorate, Pacific Northwest National Laboratory, Richland, WA 99352, USA
1 shared publication - Ethan Nickerson
Pacific Northwest National Laboratory
1 shared publication
Latest Publications
- 9 February 2023
- Published by Springer Nature
- p. 422-428
Improving the Mechanical Properties of Cast Aluminum via Ultrasonication-Induced Microstructural Refinement
- 9 February 2023
- Published by Springer Nature
- p. 422-428
Improving the Mechanical Properties of Cast Aluminum via Ultrasonication-Induced Microstructural Refinement
- 1 June 2019
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 25 (S2) , 2132-2133
EBSD Analysis of Undesired Phase Development in Solid Oxide Fuel Cell (SOFC) Lanthanum Strontium Manganese Oxide (LSM) / 8 mol% Yttrium Zirconium Oxide (8YSZ) Cathodes During Long-Term Thermal Anneal
- 1 June 2019
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 25 (S2) , 2132-2133
EBSD Analysis of Undesired Phase Development in Solid Oxide Fuel Cell (SOFC) Lanthanum Strontium Manganese Oxide (LSM) / 8 mol% Yttrium Zirconium Oxide (8YSZ) Cathodes During Long-Term Thermal Anneal
- Open Access
Investigating the Durability of Iodine Waste Forms in Dilute Conditions
To prevent the release of radioiodine during the reprocessing of used nuclear fuel or in the management of other wastes, many technologies have been developed for iodine capture. The capture is only part of the challenge as a durable waste form is required to ensure safe disposal of the radioiodine. This work presents the first durability studies in dilute conditions of two AgI-containing waste forms: hot-isostatically pressed silver mordenite (AgZ) and spark plasma sintered silver-functionalized silica aerogel (SFA) iodine waste forms (IWF). Using the single-pass flow-through (SPFT) test method, the dissolution rates respective to Si, Al, Ag and I were measured for variants of the IWFs. By combining solution and solid analysis information on the corrosion mechanism neutral-to-alkaline conditions was elucidated. The AgZ samples were observed to have corrosion preferentially occur at secondary phases with higher Al and alkali content. These phases contained a lower proportion of I compared with the matrix. The SFA samples experienced a higher extent of corrosion at Si-rich particles, but an increased addition of Si to the waste led to an improvement in corrosion resistance. The dissolution rates for the IWF types are of similar magnitude to other Si-based waste form materials measured using SPFT.
Open AccessInvestigating the Durability of Iodine Waste Forms in Dilute Conditions
To prevent the release of radioiodine during the reprocessing of used nuclear fuel or in the management of other wastes, many technologies have been developed for iodine capture. The capture is only part of the challenge as a durable waste form is required to ensure safe disposal of the radioiodine. This work presents the first durability studies in dilute conditions of two AgI-containing waste forms: hot-isostatically pressed silver mordenite (AgZ) and spark plasma sintered silver-functionalized silica aerogel (SFA) iodine waste forms (IWF). Using the single-pass flow-through (SPFT) test method, the dissolution rates respective to Si, Al, Ag and I were measured for variants of the IWFs. By combining solution and solid analysis information on the corrosion mechanism neutral-to-alkaline conditions was elucidated. The AgZ samples were observed to have corrosion preferentially occur at secondary phases with higher Al and alkali content. These phases contained a lower proportion of I compared with the matrix. The SFA samples experienced a higher extent of corrosion at Si-rich particles, but an increased addition of Si to the waste led to an improvement in corrosion resistance. The dissolution rates for the IWF types are of similar magnitude to other Si-based waste form materials measured using SPFT.
- 2 February 2018
- Published by Wiley in ChemElectroChem
- Vol. 5 (5) , 761-769
Enhanced Stability of Lithium Metal Anode by using a 3D Porous Nickel Substrate
Lithium (Li) metal is considered as the “holy grail” anode for high energy density batteries, but its applications in rechargeable Li metal batteries are still hindered by the formation of Li dendrites and low coulombic efficiency for Li plating/stripping. An effective strategy to stabilize Li metal is to embed a Li metal anode in a three‐dimensional (3D) current collector. Here, a highly porous 3D Ni substrate is reported to effectively stabilize a Li metal anode. By using a galvanostatic intermittent titration technique combined with scanning electron microscopy, the underlying mechanism of the improved stability of the Li metal anode is revealed. It is clearly demonstrated that the porous 3D Ni substrate can effectively suppress the formation of “dead” Li and support the generation of a dense surface passivation layer, while a highly porous “dead” Li layer is accumulated on the two‐dimensional (2D) Li metal, which eventually limits mass transport. X‐ray photoelectron spectroscopy results further reveal the compositional differences in the solid‐electrolyte interphase layer formed on the Li metal embedded in the porous 3D Ni substrate and the 2D Li metal substrate. These results indicate that the use of 3D conductive host is critical for the long‐term stability of Li metal batteries.
- 2 February 2018
- Published by Wiley in ChemElectroChem
- Vol. 5 (5) , 761-769
Enhanced Stability of Lithium Metal Anode by using a 3D Porous Nickel Substrate
Lithium (Li) metal is considered as the “holy grail” anode for high energy density batteries, but its applications in rechargeable Li metal batteries are still hindered by the formation of Li dendrites and low coulombic efficiency for Li plating/stripping. An effective strategy to stabilize Li metal is to embed a Li metal anode in a three‐dimensional (3D) current collector. Here, a highly porous 3D Ni substrate is reported to effectively stabilize a Li metal anode. By using a galvanostatic intermittent titration technique combined with scanning electron microscopy, the underlying mechanism of the improved stability of the Li metal anode is revealed. It is clearly demonstrated that the porous 3D Ni substrate can effectively suppress the formation of “dead” Li and support the generation of a dense surface passivation layer, while a highly porous “dead” Li layer is accumulated on the two‐dimensional (2D) Li metal, which eventually limits mass transport. X‐ray photoelectron spectroscopy results further reveal the compositional differences in the solid‐electrolyte interphase layer formed on the Li metal embedded in the porous 3D Ni substrate and the 2D Li metal substrate. These results indicate that the use of 3D conductive host is critical for the long‐term stability of Li metal batteries.