C.D. Williams
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
C.D. Williams has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Farhood Azarsina
Islamic Azad University
3 shared publications - D. Bass
Professor, Faculty of Engineering and Applied Science, Memorial University of Newfoundland
1 shared publication - J.M. Doucet
Oceanic Consulting Corporation, Suite 401, 95 Bonaventure Avenue, St. John's, NL, Canada, A1B 2X5, tel: 709-722-9060, fax: 709-722-9064
1 shared publication - Leonard Melvin Lye
Memorial University of Newfoundland, St. John’s, NL, Canada
1 shared publication - M.T. Issac
Memorial University of Newfoundland, Faculty of Engineering and Applied Science, St. John's, NL, Canada, A1B 3X5
1 shared publication - Neil Bose
Department of Ocean and Naval Architectural Engineering, Memorial University of Newfoundland, 240 Prince Philip Drive, St., John's, NL A1B 3X5, Canada
1 shared publication
Latest Publications
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01977385,p. 1-10
Re-analysis of the "Akron" Airship Pressure Data to Design Pressure Measurement Experiments on an Underwater Vehicle
Pressure experimental data from NACA tests on the airship "Akron" were reanalysed in this study. The pressure distribution over the bare hull of the airship were presented by using 3D pressure surfaces and 2D pressure contours for different pitch angles. By integration of the normal pressures at each panel over the bare hull of the airship, the axial and normal forces and the pitching moment exerted on the hull were derived. The paper has a brief introduction on how to use this re-analysis of the old experiment data to plan pressure-measurement experiments on an underwater vehicle.
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01977385,p. 1-10
Re-analysis of the "Akron" Airship Pressure Data to Design Pressure Measurement Experiments on an Underwater Vehicle
Pressure experimental data from NACA tests on the airship "Akron" were reanalysed in this study. The pressure distribution over the bare hull of the airship were presented by using 3D pressure surfaces and 2D pressure contours for different pitch angles. By integration of the normal pressures at each panel over the bare hull of the airship, the axial and normal forces and the pitching moment exerted on the hull were derived. The paper has a brief introduction on how to use this re-analysis of the old experiment data to plan pressure-measurement experiments on an underwater vehicle.
- 1 September 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Effects of Hull Length on the Hydrodynamic Loads on a Slender Underwater Vehicle during Manoeuvres
Experiments were performed with the bare hull of a full-scale, slender, body-of-revolution underwater vehicle of five different lengths, using an internal three-component balance and a planar motion mechanism (PMM). The experiments included resistance, static yaw, dynamic sway and yaw, and, circular arc runs. Results from the resistance, static yaw and sway runs are presented
- 1 September 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Effects of Hull Length on the Hydrodynamic Loads on a Slender Underwater Vehicle during Manoeuvres
Experiments were performed with the bare hull of a full-scale, slender, body-of-revolution underwater vehicle of five different lengths, using an internal three-component balance and a planar motion mechanism (PMM). The experiments included resistance, static yaw, dynamic sway and yaw, and, circular arc runs. Results from the resistance, static yaw and sway runs are presented
- 1 September 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Resistance and Static Yaw Experiments on the Underwater Vehicle "Phoenix"; Modeling and Analysis, Utilizing Statistical Design of Experiments Methodology
This research is focused on the hydrodynamic behaviour of a series of hull forms for an underwater vehicle, which includes a range of length-to-diameter ratios. Experimental data were gathered for several standard manoeuvring experiments and a reverse Design Of Experiment (DOE) was applied to the available data. From the DOE point of view, the effects of the main factors in each type of experiment were studied and an appropriate Response Surface Model (RSM) was fitted to the data. The developed empirical model is very useful in predicting the non-dimensional hydrodynamic force and moment coefficients, which is a major step in simulating the motion of an underwater vehicle
- 1 September 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Resistance and Static Yaw Experiments on the Underwater Vehicle "Phoenix"; Modeling and Analysis, Utilizing Statistical Design of Experiments Methodology
This research is focused on the hydrodynamic behaviour of a series of hull forms for an underwater vehicle, which includes a range of length-to-diameter ratios. Experimental data were gathered for several standard manoeuvring experiments and a reverse Design Of Experiment (DOE) was applied to the available data. From the DOE point of view, the effects of the main factors in each type of experiment were studied and an appropriate Response Surface Model (RSM) was fitted to the data. The developed empirical model is very useful in predicting the non-dimensional hydrodynamic force and moment coefficients, which is a major step in simulating the motion of an underwater vehicle