Visvesh S. Sathe
Visvesh S. Sathe has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Marios C. Papaefthymiou
1995 University Avenue, Berkeley
3 shared publications - Jerry C. Kao
EECS, University of Michigan, Ann Arbor, United States
2 shared publications Alexander Ishii
Berkeley
1 shared publicationCharles Ouyang
San Jose
1 shared publication- Juang-Ying Chueh
Advanced Computer Architecture Laboratory, EECS Department, University of Michigan, Ann Arbor, MI 48109
1 shared publication Marios Papaefthymiou
EECS, University of Michigan, Ann Arbor, United States
1 shared publication
Latest Publications
- 18 October 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 48 (1) , 140-149
Resonant-Clock Design for a Power-Efficient, High-Volume x86-64 Microprocessor
AMD's 32-nm x86-64 core code-named “Piledriver” features a resonant global clock distribution to reduce clock distribution power while maintaining a low clock skew. To support a wide range of operating frequencies expected of the core, the global clock system operates in two modes: a resonant-clock (rclk) mode for energy-efficient operation over a desired frequency range and a conventional, direct-drive mode (cclk) to support low-frequency operation. This dual-mode feature was implemented with minimal area impact to achieve both reduced average power dissipation and improved power-constrained performance. In Piledriver, resonant clocking achieves a peak 25% global clock power reduction at 75 °C, which translates to a 4.5% reduction in average application core power.
- 18 October 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 48 (1) , 140-149
Resonant-Clock Design for a Power-Efficient, High-Volume x86-64 Microprocessor
AMD's 32-nm x86-64 core code-named “Piledriver” features a resonant global clock distribution to reduce clock distribution power while maintaining a low clock skew. To support a wide range of operating frequencies expected of the core, the global clock system operates in two modes: a resonant-clock (rclk) mode for energy-efficient operation over a desired frequency range and a conventional, direct-drive mode (cclk) to support low-frequency operation. This dual-mode feature was implemented with minimal area impact to achieve both reduced average power dissipation and improved power-constrained performance. In Piledriver, resonant clocking achieves a peak 25% global clock power reduction at 75 °C, which translates to a 4.5% reduction in average application core power.
- 10 May 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 20 (6) , 977-988
Energy-Efficient Low-Latency 600 MHz FIR With High-Overdrive Charge-Recovery Logic
This paper presents a 14-tap 8-bit finite impulse response (FIR) test-chip that has been designed using a novel charge-recovery logic family, called Enhanced Boost Logic (EBL), to achieve high-speed and low-power operation. Compared to previous charge-recovery circuitry, EBL achieves increased gate overdrive, resulting in low latency overhead over static CMOS design. The EBL-based FIR has been designed with only 1.5 cycles of additional latency over its static CMOS counterpart, while consuming 21% less energy per cycle, based on post-layout simulations of the two designs. The test-chip has been fabricated in a 0.13 μ m CMOS process with a fully-integrated 3 nH inductor. Correct function has been validated in the 365-600 MHz range. At its resonant frequency of 466 MHz, the test-chip dissipates 39.1 mW with a 93.6 nW/MHz/Tap/InBit/CoeffBit figure of merit, recovering 45% of the energy supplied to it every cycle.
- 10 May 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 20 (6) , 977-988
Energy-Efficient Low-Latency 600 MHz FIR With High-Overdrive Charge-Recovery Logic
This paper presents a 14-tap 8-bit finite impulse response (FIR) test-chip that has been designed using a novel charge-recovery logic family, called Enhanced Boost Logic (EBL), to achieve high-speed and low-power operation. Compared to previous charge-recovery circuitry, EBL achieves increased gate overdrive, resulting in low latency overhead over static CMOS design. The EBL-based FIR has been designed with only 1.5 cycles of additional latency over its static CMOS counterpart, while consuming 21% less energy per cycle, based on post-layout simulations of the two designs. The test-chip has been fabricated in a 0.13 μ m CMOS process with a fully-integrated 3 nH inductor. Correct function has been validated in the 365-600 MHz range. At its resonant frequency of 466 MHz, the test-chip dissipates 39.1 mW with a 93.6 nW/MHz/Tap/InBit/CoeffBit figure of merit, recovering 45% of the energy supplied to it every cycle.
- 31 March 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 43 (4) , 864-873
Resonant-Clock Latch-Based Design
This paper describes RF1 and RF2, two level-clocked test-chips that deploy resonant clocking to reduce power consumption in their clock distribution networks. It also highlights RCL, a novel resonant-clock latch-based methodology that was used to design the two test-chips. RF1 and RF2 are 8-bit 14-tap finite-impulse response (FIR) filters with identical architectures. Designed using a fully automated ASIC design flow, they have been fabricated in a commercial 0.13 mum bulk silicon process. RF1 operates at clock frequencies in the 0.8-1.2 GHz range and uses a single-phase clocking scheme with a driven clock generator. Resonating its 42 pF clock load at 1.03 GHz with Vdd = 1.13 V, RF1 dissipates 132 mW, achieving a clock power reduction of 76% over conventional switching. RF2 achieves higher clock power efficiency than RF1 by relying on a two-phase clocking scheme with a distributed self-resonant clock generator. Resonating 38 pF of clock load per phase at 1.01 GHz with Vdd = 1.08 V, RF2 dissipates 124 mW and achieves 84% reduction in clock power over conventional switching. At 133 nW/MHz/Tap/InBit/CoeffBit, RF2 features the lowest figure of merit for FIR filters published to date.
- 31 March 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 43 (4) , 864-873
Resonant-Clock Latch-Based Design
This paper describes RF1 and RF2, two level-clocked test-chips that deploy resonant clocking to reduce power consumption in their clock distribution networks. It also highlights RCL, a novel resonant-clock latch-based methodology that was used to design the two test-chips. RF1 and RF2 are 8-bit 14-tap finite-impulse response (FIR) filters with identical architectures. Designed using a fully automated ASIC design flow, they have been fabricated in a commercial 0.13 mum bulk silicon process. RF1 operates at clock frequencies in the 0.8-1.2 GHz range and uses a single-phase clocking scheme with a driven clock generator. Resonating its 42 pF clock load at 1.03 GHz with Vdd = 1.13 V, RF1 dissipates 132 mW, achieving a clock power reduction of 76% over conventional switching. RF2 achieves higher clock power efficiency than RF1 by relying on a two-phase clocking scheme with a distributed self-resonant clock generator. Resonating 38 pF of clock load per phase at 1.01 GHz with Vdd = 1.08 V, RF2 dissipates 124 mW and achieves 84% reduction in clock power over conventional switching. At 133 nW/MHz/Tap/InBit/CoeffBit, RF2 features the lowest figure of merit for FIR filters published to date.
- 1 September 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 777-780
900MHz to 1.2GHz Two-Phase Resonant Clock Network with Programmable Driver and Loading
A resonant clock network with programmable driver and loading is designed in a 0.13mum CMOS technology. The 2mm times 2mm distribution network has on-chip inductors and performs a forced oscillation at the rate of a reference clock programmable in the 900MHz to 1.2GHz range. Clock amplitude and energy efficiency trade-offs at and off resonance are explored with various driver configurations. Energy efficiency per cycle is 1.39 to 1.56 times greater than previous resonant distribution networks
- 1 September 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 777-780
900MHz to 1.2GHz Two-Phase Resonant Clock Network with Programmable Driver and Loading
A resonant clock network with programmable driver and loading is designed in a 0.13mum CMOS technology. The 2mm times 2mm distribution network has on-chip inductors and performs a forced oscillation at the rate of a reference clock programmable in the 900MHz to 1.2GHz range. Clock amplitude and energy efficiency trade-offs at and off resonance are explored with various driver configurations. Energy efficiency per cycle is 1.39 to 1.56 times greater than previous resonant distribution networks