Alana Tavares

Purpose To investigate whether there is a relationship between the volume of the maxillary sinus and individual parameters such as gender, side, posterior tooth absence, sinus membrane thickening, bony septa, vertical and sagittal skeletal patterns. Methods The tomographic volume of the maxillary sinus from 211 individuals (422 sides) was evaluated using Horos DICOM Viewer Software. Bony septa and sinus membrane thickening were classified as absent or present. At the same time, loss of one or more teeth in the posterior region of the maxilla (except for the third molars) was considered. The t test was applied to analyze maxillary sinus volume according to gender, age, side, posterior tooth absence, sinus membrane thickening and bony septa. A one-way analysis of variance (ANOVA) with Tukey’s post-hoc test was applied to compare sagittal and vertical patterns. Pearson’s correlation coefficient was also used to verify the association between maxillary sinus volume, age and skeletal patterns. Results Concerning the sagittal skeletal pattern, a statistically significant difference was observed between Classes II and III (p = 0.05) and it was confirmed by the Pearson’s correlation coefficient (r = − 0.107/p = 0.029). No statistically significant differences were observed between the maxillary sinus volume according to gender (p = 0.06), side (p = 0.37), posterior tooth absence (p = 0.92), sinus membrane thickening (p = 0.47), bony septa (0.89) and vertical skeletal pattern (p = 0.67). No significant differences were observed with age (r = − 0.076/p = 0.109) and the vertical skeletal pattern (r = − 0.078/p = 0.108). Conclusion Maxillary sinus volume was influenced by the sagittal skeletal pattern and was higher in Class III individuals.

Introduction: The aim of the present study was to evaluate the thickness of the hard palate at the different angles formed by the palatal plane and the Frankfort horizontal line using computed tomography in patients with different facial patterns for planning the installation of MARPE.Materials and methods: The measurements were analysed in the hard palate of 106 patients. Four regions were selected passing through the mesial face, tangent at the level of the cemento‐enamel junction of the premolars and molars. The bone thickness was measured from the floor of the nasal cavity to the cortical bone of the hard palate, 02 measurements with a distance of 05 mm between them (2.5 mm on each side starting from the midsagittal line) and 2 more with a distance of 7 mm between measurements (3.5 mm on each side starting from the midsagittal line). The palatal plane cant was determined based on the palatal plane and the Frankfort horizontal plane. The sagittal skeletal pattern was determined based on the ANB angle and the vertical skeletal pattern based on the SN.Go.Gn angle.Results: Palatal bone thickness was greater in males than in females. Regarding the sagittal skeletal pattern, patients with Class II were found to have a thinner hard palate than Class I and Class III patients. No difference in the vertical skeletal pattern was observed between groups. Regarding the palatal plane cant, bone thickness was greater in patients with clockwise rotation.Conclusions: Careful planning should be considered in the case of female patients; patients with greater angles of the palatal plane cant and Class II patients have a smaller bone thickness.

Objective: To evaluate bone availability at the infrazygomatic crest for extra‐alveolar bone miniscrew insertion in subjects with different vertical and sagittal skeletal patterns.Setting and sample population: Measurements of the infrazygomatic crest were performed on multislice computed tomography scans from 58 adults with different skeletal patterns.Materials and methods: Infrazygomatic crest bone depth was measured at 4, 5 and 6 mm from the cementoenamel junction (CEJ) of the maxillary first molar at three different angles (60°, 70° and 80°) in the first molar occlusal plane. The sagittal and vertical skeletal patterns were determined. Analysis of variance followed by Tukey's post hoc test was used (P ≤ .05).Results: Bone depth was greater near the CEJ (8.7 ± 3.1 mm) and lower in the apical area (5.8 ± 2.7 mm). In Class II subjects, considering 6 mm from the CEJ, there was a significantly lower depth at the 80° angle (5.4 ± 2.5 mm) than at 60° (8.6 ± 3.5 mm; P = .007). In mesofacial subjects, considering 5 and 6 mm from the CEJ, bone depth was lower at 80° (5.7 ± 3.2 mm and 5.3 ± 2.5 mm) than at 60° considering 4 mm from the CEJ (P ≤ .019).Conclusion: Bone availability was lower at the apical level, especially in Class II and mesofacial subjects. Therefore, when the planned insertion site is located in the apical direction, it is recommended to choose shorter miniscrews (2.0 x 12mm) and a smaller insertion angle (60°) and/or to plan a miniscrew bone insertion deep enough to allow bicortical fixation.

Analysis of the anatomy of the region during preoperative planning is very important in order to minimize the risks of undesired movements in the supporting teeth or even damage to important structures such as the maxillary sinus. To the best of our knowledge, no study evaluated the relationship of these skeletal patterns with the anatomy of the infrazygomatic crest. The aim of this study was to evaluate the tomographic measurements of the infrazygomatic crest for placement of temporary anchorage devices in individuals with different vertical and sagittal skeletal patterns. The measurements were analyzed in three regions in the crest of 67 patients above the maxillary first molar: A slice in the long axis of the mesiobuccal root, a slice passing through the center of the furcation area of the tooth, and another slice in the long axis of the distobuccal root. In each of these slices five measurements of the thickness of the infrazygomatic crest were performed, with a difference of 1 mm between them. The sagittal skeletal pattern was determined by the ANB angle and the vertical skeletal pattern by the SN.GoGn angle. The bone thickness of the crest tended to decrease gradually in the apical direction. There was no difference between different vertical and sagittal skeletal patterns. The individual parameters did not have significant influence in the thickness of the infrazygomatic crest. Key words:Tomography, X-Ray Computed, orthodontics, mini-implant, infrazygomatic crest, maxilla.

Introduction: Plaster dental casts are routinely used during clinical practice to access maxillary dental arch form and assist on fabrication of individualized orthodontic archwires. Recently introduced, digital model technology may offer a limitation for the obtainment of a dental physical record. In this context, a tool for dental arch form assessment for chairside use is necessary when employing digital models. In this regard, paper print of the dental arch seems thus to be useful. Methods: In the present study, 37 lower arch models were used. Intercanine and intermolar widths and dental arch length measurements were performed and compared using plaster dental casts, digital models and paper print image of the models. Ortho Insight 3D scanner was employed for model digitalization. Results: No statistically significant differences were noted regarding the measurements performed on the plaster or digital models (p> 0.05). Paper print images, however, showed subestimated values for intercanine and intermolar widths and overestimated values for dental arch length. Despite being statistically significant (p< 0.001), the differences were considered clinically negligible. Conclusion: The present study suggests that paper print images obtained from digital models are clinically accurate and can be used as a tool for dental arch form assessment for fabrication of individualized orthodontic archwires.