Hugh C. Higley
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hugh C. Higley has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Aurelio Hafalia
Lawrence Berkeley National Laboratory, Berkeley, CA, USA
2 shared publications - GianLuca Sabbi
Lawrence Berkeley National Laboratory
2 shared publications - Ian Pong
Lawrence Berkeley National Laboratory
2 shared publications - Soren Prestemon
Lawrence Berkeley National Laboratory
2 shared publications A. Godeke
Lawrence Berkeley Nat. Lab., Berkeley, CA, USA
1 shared publication- A. Godeke
Lawrence Berkeley National Laboratory, Berkeley, CA 94720, USA
1 shared publication
Latest Publications
- 12 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (7) , 1-5
Cable Design and Development for the High-Temperature Superconductor Cable Test Facility Magnet
A large bore “High-Temperature Superconductor Cable Test Facility Magnet” for testing advanced cables and inserts in high transverse field is in its design phase. This magnet will be the core component of a facility for developing conductors and accelerator magnets operating above 15 T, an enabling technology for next-generation fusion devices using magnetic confinement of plasma and for future energy frontier colliders. The procurement of Nb 3 Sn conductor, fabrication of cables, winding of coils, and assembly of the dipole magnet will be done at Lawrence Berkeley National Laboratory (LBNL) and the test pit and cryostat will be constructed at Fermi National Accelerator Laboratory. This article will present the conductor element of the LBNL project, specifically cable design parameters (based on the Bruker OST RRP $^{\bigcirc \!\!\!\! {\hbox{R}}}$ Nb 3 Sn superconducting wire) and the development phase cable fabrication experience. Challenges of the cable fabrication will be discussed. The wire and cable planned for this magnet are similar to those under study for the Future Circular Collider and other large facility magnets. The successful fabrication of the development cable has positive implications for these other projects.
- 12 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (7) , 1-5
Cable Design and Development for the High-Temperature Superconductor Cable Test Facility Magnet
A large bore “High-Temperature Superconductor Cable Test Facility Magnet” for testing advanced cables and inserts in high transverse field is in its design phase. This magnet will be the core component of a facility for developing conductors and accelerator magnets operating above 15 T, an enabling technology for next-generation fusion devices using magnetic confinement of plasma and for future energy frontier colliders. The procurement of Nb 3 Sn conductor, fabrication of cables, winding of coils, and assembly of the dipole magnet will be done at Lawrence Berkeley National Laboratory (LBNL) and the test pit and cryostat will be constructed at Fermi National Accelerator Laboratory. This article will present the conductor element of the LBNL project, specifically cable design parameters (based on the Bruker OST RRP $^{\bigcirc \!\!\!\! {\hbox{R}}}$ Nb 3 Sn superconducting wire) and the development phase cable fabrication experience. Challenges of the cable fabrication will be discussed. The wire and cable planned for this magnet are similar to those under study for the Future Circular Collider and other large facility magnets. The successful fabrication of the development cable has positive implications for these other projects.
- 9 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-5
Diameter Quality Control of Nb3Sn Wires for MQXF Cables in the USA
The 0.850 ± 0.003 mm Nb 3 Sn wires for the low-beta quadrupole magnets “MQXFA” procured for the U.S. LHC Accelerator R&D Program (LARP) and the U.S. High Luminosity LHC Accelerator Upgrade Project (US HL-LHC AUP, or simply AUP) are received at Lawrence Berkeley National Laboratory (LBNL). There, the wires are respooled and then fabricated into Rutherford cables for winding coils. As part of the quality control program, AUP obtains from the wire manufacturer values of the maximum, average, minimum, and standard deviation of the two orthogonal axes, which are assessed prior to shipment approval. At LBNL, a dual-axis optical micrometer is used to measure the wire diameter of each spool every ∼30 cm prior to cabling. This helps decide whether wire pieces with abnormal diameters should be distributed across the cable cross section, in order to improve cable parameter quality and mechanical stability consistency. This paper presents: 1) diameter data of LARP cables and of the first AUP cables made using wires acquired under LARP; 2) our deviation acceptance/rejection justification; and 3) the impact of wire diameter statistics on cable fabrication.
- 9 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-5
Diameter Quality Control of Nb3Sn Wires for MQXF Cables in the USA
The 0.850 ± 0.003 mm Nb 3 Sn wires for the low-beta quadrupole magnets “MQXFA” procured for the U.S. LHC Accelerator R&D Program (LARP) and the U.S. High Luminosity LHC Accelerator Upgrade Project (US HL-LHC AUP, or simply AUP) are received at Lawrence Berkeley National Laboratory (LBNL). There, the wires are respooled and then fabricated into Rutherford cables for winding coils. As part of the quality control program, AUP obtains from the wire manufacturer values of the maximum, average, minimum, and standard deviation of the two orthogonal axes, which are assessed prior to shipment approval. At LBNL, a dual-axis optical micrometer is used to measure the wire diameter of each spool every ∼30 cm prior to cabling. This helps decide whether wire pieces with abnormal diameters should be distributed across the cable cross section, in order to improve cable parameter quality and mechanical stability consistency. This paper presents: 1) diameter data of LARP cables and of the first AUP cables made using wires acquired under LARP; 2) our deviation acceptance/rejection justification; and 3) the impact of wire diameter statistics on cable fabrication.
- 11 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 25 (3) , 1-4
Bi-2212 Canted-Cosine-Theta Coils for High-Field Accelerator Magnets
report on wind-and-react (W&R) Bi2Sr2CaCu2O8+x (Bi-2212) insert coils that were fabricated using a Canted-Cosine-Theta (CCT) coil technology. In the CCT technology, a conductor is wound into canted helical channels that are machined into cylindrical coil winding mandrels, thereby creating a cosine-theta current distribution and providing stress support at the conductor level. The prevention of stress accumulations by the internal structure of winding mandrels is considered an enabling technology for high field Bi-2212 insert coils that target the 20 T magnetic field range. We report on the fabrication and reaction of coils for two proof-of-principle Bi-2212 inserts, BIN1 and BIN2, each consisting of two CCT coils. The BIN1 coils use insulated 0.8 mm diameter wires and INCONEL 600 coil winding mandrels with a stainless steel 316 shell, an overall diameter of 50.0 mm and a clear bore of 35.3 mm. The BIN2 coils use insulated 6-around-1 cables from 0.8-mm diameter wires, and aluminum-bronze mandrels with an aluminum alloy 6061 shell, an overall outer diameter of 68.6 mm, and a clear bore of 38.8 mm. The coils are designed to study the fabrication, reaction, and impregnation in Bi-2212 CCT technology, and provide a baseline for a Rutherford cable-wound coil set (BIN3). These latter coils target an insert-coil set with optimized current density in the windings, to enable the construction of an 18 T Nb3Sn-Bi-2212 hybrid dipole magnet.
- 11 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 25 (3) , 1-4
Bi-2212 Canted-Cosine-Theta Coils for High-Field Accelerator Magnets
report on wind-and-react (W&R) Bi2Sr2CaCu2O8+x (Bi-2212) insert coils that were fabricated using a Canted-Cosine-Theta (CCT) coil technology. In the CCT technology, a conductor is wound into canted helical channels that are machined into cylindrical coil winding mandrels, thereby creating a cosine-theta current distribution and providing stress support at the conductor level. The prevention of stress accumulations by the internal structure of winding mandrels is considered an enabling technology for high field Bi-2212 insert coils that target the 20 T magnetic field range. We report on the fabrication and reaction of coils for two proof-of-principle Bi-2212 inserts, BIN1 and BIN2, each consisting of two CCT coils. The BIN1 coils use insulated 0.8 mm diameter wires and INCONEL 600 coil winding mandrels with a stainless steel 316 shell, an overall diameter of 50.0 mm and a clear bore of 35.3 mm. The BIN2 coils use insulated 6-around-1 cables from 0.8-mm diameter wires, and aluminum-bronze mandrels with an aluminum alloy 6061 shell, an overall outer diameter of 68.6 mm, and a clear bore of 38.8 mm. The coils are designed to study the fabrication, reaction, and impregnation in Bi-2212 CCT technology, and provide a baseline for a Rutherford cable-wound coil set (BIN3). These latter coils target an insert-coil set with optimized current density in the windings, to enable the construction of an 18 T Nb3Sn-Bi-2212 hybrid dipole magnet.
- 1 January 2012
- Published by AIP Publishing in AIP Conference Proceedings
- p. 209-216
Novel methods for the measurement of the critical current of superconducting wires
The critical current as a function of magnetic field of superconducting wires is commonly measured using about 60 mm short straight, or U-shaped samples, or about 1 m long samples on helical mandrels (so-called ITER barrels). The ITER barrel is designed for low to medium currents, but is commonly modified for high current wires. This often results in increased complexity, errors from reacted sample handling, preparation time, and cost. We have developed a method that retains the standard ITER barrel, but uses disposable, off the-shelf, plumbers, Cu tube fittings instead of machined end-rings, thereby resolving the aforementioned issues. The improved sample holder also solves a number of disadvantages of the original ITER barrel method. A second method involves the improvement of straight wire measurements. Current redistributions, resulting from the limited length in perpendicular magnetic field, reduce the achievable voltage resolution in short straight, or U-shaped samples. We have introduced "wiggles" in U-shaped short samples, which impose the appropriate current distribution far before the region of interest, thereby mitigating undesired redistributions around the voltage measurement region. Both improved methods allow for an increased throughput and reliability of critical current measurements on superconducting wires.
- 1 January 2012
- Published by AIP Publishing in AIP Conference Proceedings
- p. 209-216
Novel methods for the measurement of the critical current of superconducting wires
The critical current as a function of magnetic field of superconducting wires is commonly measured using about 60 mm short straight, or U-shaped samples, or about 1 m long samples on helical mandrels (so-called ITER barrels). The ITER barrel is designed for low to medium currents, but is commonly modified for high current wires. This often results in increased complexity, errors from reacted sample handling, preparation time, and cost. We have developed a method that retains the standard ITER barrel, but uses disposable, off the-shelf, plumbers, Cu tube fittings instead of machined end-rings, thereby resolving the aforementioned issues. The improved sample holder also solves a number of disadvantages of the original ITER barrel method. A second method involves the improvement of straight wire measurements. Current redistributions, resulting from the limited length in perpendicular magnetic field, reduce the achievable voltage resolution in short straight, or U-shaped samples. We have introduced "wiggles" in U-shaped short samples, which impose the appropriate current distribution far before the region of interest, thereby mitigating undesired redistributions around the voltage measurement region. Both improved methods allow for an increased throughput and reliability of critical current measurements on superconducting wires.