Jiaqing Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jiaqing Wu has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Robert E. Williams
Univ. of Nebraska, Lincoln, NE (United States)
2 shared publications - Weilong Cong
Department of Industrial, Manufacturing, and System Engineering, Texas Tech University, Lubbock, TX 79409, USA
2 shared publications - Zhijian Pei
Department of Industrial and Manufacturing Systems Engineering, Kansas State University, Manhattan, KS 66506, United States
2 shared publications
Latest Publications
- 1 August 2011
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 133 (4) , 041012
Dynamic Process Modeling for Rotary Ultrasonic Machining of Alumina
Rotary ultrasonic machining (RUM) is a hybrid machining approach that combines two material removal mechanisms, namely, diamond grinding and ultrasonic machining. This paper presents the results of dynamic process modeling for RUM of alumina, as currently available literature mainly focuses on static parametric relationships. A stochastic modeling and analysis technique called data dependent systems (DDS) was used to study RUM generated surface profiles and cutting force signals. Variations in the data sets of surface profiles, for the entrance and exit segments of machined holes and for that of machined rods, and cutting force signals were modeled and decomposed to gain insight into the RUM process mechanism. The DDS wavelength decomposition of the surface profiles suggested that the major characteristic root wavelength had a positive correlation with feed rate, and the wavelength magnitude may be linked to the grain size of the workpiece material. The roughness of machined surfaces increased as the tool moved deeper due to reduced flushing efficiency. Surfaces on the machined rods were less sensitive to the input variables than the hole surfaces. Moreover, spindle speed and feed rate affected the cutting force significantly.
- 1 August 2011
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 133 (4) , 041012
Dynamic Process Modeling for Rotary Ultrasonic Machining of Alumina
Rotary ultrasonic machining (RUM) is a hybrid machining approach that combines two material removal mechanisms, namely, diamond grinding and ultrasonic machining. This paper presents the results of dynamic process modeling for RUM of alumina, as currently available literature mainly focuses on static parametric relationships. A stochastic modeling and analysis technique called data dependent systems (DDS) was used to study RUM generated surface profiles and cutting force signals. Variations in the data sets of surface profiles, for the entrance and exit segments of machined holes and for that of machined rods, and cutting force signals were modeled and decomposed to gain insight into the RUM process mechanism. The DDS wavelength decomposition of the surface profiles suggested that the major characteristic root wavelength had a positive correlation with feed rate, and the wavelength magnitude may be linked to the grain size of the workpiece material. The roughness of machined surfaces increased as the tool moved deeper due to reduced flushing efficiency. Surfaces on the machined rods were less sensitive to the input variables than the hole surfaces. Moreover, spindle speed and feed rate affected the cutting force significantly.
- 1 January 2009
- Published by ASME International
- p. 283-292
Stochastic Modeling and Analysis of Rotary Ultrasonic Machining
Rotary Ultrasonic Machining (RUM) is a hybrid machining approach that combines two material removal mechanisms, namely diamond grinding and ultrasonic machining. Currently available literature mainly focuses on static parametric relationships. This paper presents preliminary results of an experimental study on some aspects of the RUM process performance, surface integrity, and dynamic process modeling. A stochastic modeling and analysis technique called Data Dependent Systems (DDS) was used to study RUM generated surface profiles and cutting force signals. The DDS wavelength decomposition of the surface profiles suggested that the major characteristic root wavelength had a positive correlation with feed rate, and the wavelength magnitude may be linked to the grain size of the workpiece material. In addition, the difference of the major wavelength between the surface profiles for machined holes and that for machined rods was investigated. The surface variation between the entrance and exit segments of both holes and rods were also studied. Moreover, the DDS modeling approach was applied to cutting force signals collected during RUM and comparisons were made to the surface profiles results.
- 1 January 2009
- Published by ASME International
- p. 283-292
Stochastic Modeling and Analysis of Rotary Ultrasonic Machining
Rotary Ultrasonic Machining (RUM) is a hybrid machining approach that combines two material removal mechanisms, namely diamond grinding and ultrasonic machining. Currently available literature mainly focuses on static parametric relationships. This paper presents preliminary results of an experimental study on some aspects of the RUM process performance, surface integrity, and dynamic process modeling. A stochastic modeling and analysis technique called Data Dependent Systems (DDS) was used to study RUM generated surface profiles and cutting force signals. The DDS wavelength decomposition of the surface profiles suggested that the major characteristic root wavelength had a positive correlation with feed rate, and the wavelength magnitude may be linked to the grain size of the workpiece material. In addition, the difference of the major wavelength between the surface profiles for machined holes and that for machined rods was investigated. The surface variation between the entrance and exit segments of both holes and rods were also studied. Moreover, the DDS modeling approach was applied to cutting force signals collected during RUM and comparisons were made to the surface profiles results.