Dilip Dhondiram Shivagan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dilip Dhondiram Shivagan has a total of 101 co-authors. Here are the top co-authors by number of shared publications:
- Akira Iyo
National Institute of Advanced Industrial Science and Technology (AIST)
25 shared publications - Yasumoto Tanaka
National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Ibaraki 305-8568, Japan
25 shared publications - Adrian Crisan
National Institute of Materials Physics, 405A Atomistilor Str., 077125 Magurele, Romania
18 shared publications P M Shirage
National Institute of Advanced Industrial Science and Technology (AIST), 1–1–1 Umezono, Tsukuba, Ibaraki 305–8568, Japan
13 shared publicationsUmesh Pant
CSIR - National Physical Laboratory
8 shared publicationsK Tokiwa
Department of Applied Electronics, Tokyo University of Science, 2641 Yamazaki, Noda, Chiba 278–3510, Japan
7 shared publications
Latest Publications
- 1 November 2025
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 14 (11) , 117002
InSb Thin Film as an NIR Photodetector and Self-Powered Non-Contact Infrared Temperature Sensor
This study demonstrates an InSb based detector, uniquely capable of dual functionality operating both as an infrared photodetector and as a temperature sensor within a single device architecture. The InSb/Si 3 N 4 /Si based device architecture exhibits a dual functionality as a near-infrared (NIR) photodetector and a self-powered, non-contact infrared temperature sensor. The photodetection performance was evaluated under 1064 nm NIR LASER illumination, yielding rapid response and recovery times of 39 ms and 41 ms, respectively. At a low operating bias of 2 V, the device demonstrated a high detectivity of 2.05 × 10 8 Jones and a responsivity of 0.23 mA W −1 . The same architecture, with planar Ag contacts, exhibited strong infrared thermal sensitivity when exposed to standard blackbody radiation at temperatures ranging from 800 °C to 1200 °C, with distinct on–off switching characteristics. Notably, temperature sensing was achieved in a self-powered mode at room temperature, attributed to the formation of a built-in depletion region at the metal–semiconductor (Ag–InSb) interface. These results underscore the potential of sputter deposited InSb thin films for integrated, low-power optoelectronic applications. The dual operational capability enhances the versatility for practical applications and distinguishes it from conventional InSb detectors designed for only one mode of operation.
- 1 November 2025
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 14 (11) , 117002
InSb Thin Film as an NIR Photodetector and Self-Powered Non-Contact Infrared Temperature Sensor
This study demonstrates an InSb based detector, uniquely capable of dual functionality operating both as an infrared photodetector and as a temperature sensor within a single device architecture. The InSb/Si 3 N 4 /Si based device architecture exhibits a dual functionality as a near-infrared (NIR) photodetector and a self-powered, non-contact infrared temperature sensor. The photodetection performance was evaluated under 1064 nm NIR LASER illumination, yielding rapid response and recovery times of 39 ms and 41 ms, respectively. At a low operating bias of 2 V, the device demonstrated a high detectivity of 2.05 × 10 8 Jones and a responsivity of 0.23 mA W −1 . The same architecture, with planar Ag contacts, exhibited strong infrared thermal sensitivity when exposed to standard blackbody radiation at temperatures ranging from 800 °C to 1200 °C, with distinct on–off switching characteristics. Notably, temperature sensing was achieved in a self-powered mode at room temperature, attributed to the formation of a built-in depletion region at the metal–semiconductor (Ag–InSb) interface. These results underscore the potential of sputter deposited InSb thin films for integrated, low-power optoelectronic applications. The dual operational capability enhances the versatility for practical applications and distinguishes it from conventional InSb detectors designed for only one mode of operation.
- 24 August 2023
- Published by Springer Nature
- p. 235-268
Quantum Definition of New Kelvin and Way Forward
- 24 August 2023
- Published by Springer Nature
- p. 235-268
Quantum Definition of New Kelvin and Way Forward
- 21 March 2023
- Published by Springer Nature in MAPAN
- Vol. 38 (2) , 307-315
Development of Nickel–Carbon Eutectic Fixed Point Cell for Thermocouple Thermometry
- 21 March 2023
- Published by Springer Nature in MAPAN
- Vol. 38 (2) , 307-315
Development of Nickel–Carbon Eutectic Fixed Point Cell for Thermocouple Thermometry
- 1 March 2023
- Published by Springer Nature
- p. 1-34
Quantum Definition of New Kelvin and Way Forward
- 4 October 2021
- Published by Springer Nature in MAPAN
- Vol. 37 (1) , 3-13
Realization of ITS-90 Radiance Temperature Scale from 961.78 °C to 3000 °C at CSIR-NPL
- 4 October 2021
- Published by Springer Nature in MAPAN
- Vol. 37 (1) , 3-13
Realization of ITS-90 Radiance Temperature Scale from 961.78 °C to 3000 °C at CSIR-NPL
- 29 July 2021
- Published by Springer Nature in MAPAN
- Vol. 36 (3) , 615-628
Improved Realization of Ensemble of Triple Point of Water Cells at CSIR-NPL
- 29 July 2021
- Published by Springer Nature in MAPAN
- Vol. 36 (3) , 615-628
Improved Realization of Ensemble of Triple Point of Water Cells at CSIR-NPL
- 10 November 2020
- Published by Springer Nature
- p. 307-376
Physico-Mechanical Metrology
This chapter describes the three physico-mechanical metrology streams; temperature and humidity, optical radiation and acoustic and vibration metrology. Among the seven base SI units, temperature and optical radiation encompasses the two SI units while acoustic comprises only derived parameters. Temperature metrology includes realization and dissemination of temperature and humidity parameters, optical radiation metrology includes parameters like illuminance, illuminance responsivity, luminous flux, luminance, colour temperature, colour coordinates and spectral irradiances. Acoustic metrology includes sound pressure, vibration amplitude, sound transmission and absorption coefficients. All the parameters are inter-connected to fulfil the human needs and endeavours and have immense importance in the socio-economic growth of the country. The contribution, insinuation, impact, significance and relevance of these PMPs in different sectors like health, process and manufacturing, lighting industry, building acoustics, SODAR system and noise mapping are described along with established measurement standards and facilities, CMCs, participation in key comparisons, gap analysis and futuristic requirements and suggestions. All these endeavours are carried for the inclusive industrial growth of the nation.
- 10 November 2020
- Published by Springer Nature
- p. 307-376
Physico-Mechanical Metrology
This chapter describes the three physico-mechanical metrology streams; temperature and humidity, optical radiation and acoustic and vibration metrology. Among the seven base SI units, temperature and optical radiation encompasses the two SI units while acoustic comprises only derived parameters. Temperature metrology includes realization and dissemination of temperature and humidity parameters, optical radiation metrology includes parameters like illuminance, illuminance responsivity, luminous flux, luminance, colour temperature, colour coordinates and spectral irradiances. Acoustic metrology includes sound pressure, vibration amplitude, sound transmission and absorption coefficients. All the parameters are inter-connected to fulfil the human needs and endeavours and have immense importance in the socio-economic growth of the country. The contribution, insinuation, impact, significance and relevance of these PMPs in different sectors like health, process and manufacturing, lighting industry, building acoustics, SODAR system and noise mapping are described along with established measurement standards and facilities, CMCs, participation in key comparisons, gap analysis and futuristic requirements and suggestions. All these endeavours are carried for the inclusive industrial growth of the nation.
- 21 May 2020
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 41 (7) , 1-15
Development and Realization of Fe–C and Co–C Eutectic Fixed-Point Blackbodies for Radiation Thermometry at CSIR-NPL
- 21 May 2020
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 41 (7) , 1-15
Development and Realization of Fe–C and Co–C Eutectic Fixed-Point Blackbodies for Radiation Thermometry at CSIR-NPL
- 27 July 2019
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 40 (8) , 1-14
Development and Long-Term Stability Assessment of Co–C Eutectic Fixed Point for Thermocouple Thermometry
- 27 July 2019
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 40 (8) , 1-14
Development and Long-Term Stability Assessment of Co–C Eutectic Fixed Point for Thermocouple Thermometry
- 25 January 2018
- Published by Springer Nature in MAPAN
- Vol. 33 (3) , 201-208
Development and Realization of Iron–Carbon Eutectic Fixed Point at NPLI
- 25 January 2018
- Published by Springer Nature in MAPAN
- Vol. 33 (3) , 201-208
Development and Realization of Iron–Carbon Eutectic Fixed Point at NPLI