GGGuy Gauthier

Guy Gauthier

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Guy Gauthier has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    New Validation Methodology of an Adaptive Wing for UAV S45 for Fuel Reduction and Climate Improvement

    by Manuel Flores Salinas, Ruxandra Mihaela Botez, Guy Gauthier

    New knowledge in multidisciplinary methodology is presented in this article for the design, aerodynamic optimization, and model validation of an adaptive wing prototype. The optimization framework integrates the design, the finite element analysis, and the model validation. A computational fluid dynamics model of the adaptive wing and the flow in its vicinity was developed and validated with experimental metrics, such as the lift, the drag, and the lift-to-drag ratio. A new genetic algorithm strategy was chosen to find the optimized airfoil shapes for the prototype’s upper surface. The reliability of the proposed methodology was investigated through the design, manufacture, and testing of a wing prototype proposed for the UAV S45. The experimental and simulated results have shown a low drag production and a high lift-to-drag ratio of the adaptive wing prototype that will translate into a reduction in fuel consumption and an increase in cruising flight range and therefore into climate improvement.


  • Open Access

    New Numerical and Measurements Flow Analyses Near Radars

    by Manuel Flores Salinas, Ruxandra Mihaela Botez, Guy Gauthier

    An experimental and numerical investigation of the flow near a blunt body has been conducted in this study. Most experimental methods of flow studies use flow visualization and probes introduction into the flow field. The main goal of this research was the development of a new methodology to analyze flows, and to measure flow characteristics without taking into account the distorting effects of measuring probes. A series of experiments were performed on a ground surveillance radar in the Price-Païdoussis subsonic wind tunnel. Forces and moments were measured as functions of wind speeds and angular positions by the use of a six-component aerodynamic scale. A Computational Fluid Dynamics three-dimensional model was employed to analyze the wake region of the ground surveillance radar. A turbulence reduction system was proposed and analyzed in this research. The use of the proposed turbulence reduction system was found to be an effective way to reduce turbulent flow intensity by 50%, drag coefficients by 9.6%, and delay the flow transition point by 7.6 times.


  • Open Access

    Automatic Temperature Setpoint Tuning of a Thermoforming Machine using Fuzzy Terminal Iterative Learning Control

    by Mathieu Beauchemin-Turcotte, Guy Gauthier, Robert Sabourin

    This paper presents a new way to design a Fuzzy Terminal Iterative Learning Control (TILC) to control the heater temperature setpoints of a thermoforming machine. This fuzzy TILC is based on the inverse of a fuzzy model of this machine, and is built from experimental (or simulation) data with kriging interpolation. The Fuzzy Inference System usually used for a fuzzy model is the zero order Takagi Sugeno Kwan system (constant consequents). In this paper, the 1st order Takagi Sugeno Kwan system is used, with the fuzzy model rules expressed using matrices. This makes the inversion of the fuzzy model much easier than the inversion of the fuzzy model based on the TSK of order 0. Based on simulation results, the proposed fuzzy TILC seems able to give a very good initial guess as to the heater temperature setpoints, making it possible to have almost no wastage of plastic sheets. Simulation results show the effectiveness of the fuzzy TILC compared to a crisp TILC, even though the fuzzy controller is based on a fuzzy model built from noisy data.

  • Open Access

    Robust Design of Terminal ILC with H∞ Mixed Sensitivity Approach for a Thermoforming Oven

    by Guy Gauthier, Benoit Boulet

    This paper presents a robust design approach for terminal iterative learning control (TILC). This robust design uses the H∞ mixed‐sensitivity technique. An industrial application is described where TILC is used to control the reheat phase of plastic sheets in a thermoforming oven. The TILC adjusts the heater temperature setpoints such that, at the end of the reheat cycle, the surface temperature map of the plastic sheet will converge to the desired one. Simulation results are included to show the effectiveness of the control law.


  • Modeling and Simulation of a Multivariable Process Control

    by E. Cornieles, M. Saad, G. Gauthier, Hamadou Saliah-Hassane

    This paper presents a comparative survey of different multivariable techniques applied to process control. The modeling of the physical system and real time simulations are also presented using different PID structures and applied for the regulation of level and the temperature of a water reservoir control process. The structure of the multivariable control system has been implanted using LabViewreg software. This structure uses two control loops, the first for the level regulation and the second for the regulation of temperature. Five different PID controllers are included in this paper (Ziegler_Nichols, ITAE, IMC, poles placement and dual loop) and real time results are presented