Meryem Farchado
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Meryem Farchado has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Angel Morales
Mat Concentrating Solar Thermal Technol Unit, CIEMAT PSA, Ave Complutense 40, Madrid 28040, Spain
8 shared publications - Gema San Vicente
Mat Concentrating Solar Thermal Technol Unit, CIEMAT PSA, Ave Complutense 40, Madrid 28040, Spain
7 shared publications - Naia Barandica
Mat Concentrating Solar Thermal Technol Unit, CIEMAT PSA, Ave Complutense 40, Madrid 28040, Spain
3 shared publications - Daniel Sanchez-Señoran
Centro de Investigaciones Energéticas
2 shared publications - Florian Sutter
German Aerospace Center
2 shared publications - Nuria Germán
Unidad de Materiales para Tecnologías Termosolares de Concentración, Plataforma Solar de Almería, Departamento de Energía, Centro de Investigaciones Energéticas, Medioambientales y Tecnológicas (CIEMAT), Avda. Complutense 40, 28040 Madrid, Spain
2 shared publications
Latest Publications
- 7 November 2024
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 279
Novel highly performing tandem selective solar absorber for industrial heat applications
- 7 November 2024
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 279
Novel highly performing tandem selective solar absorber for industrial heat applications
- Open Access
- 16 April 2024
- Published by TIB Open Publishing in SolarPACES Conference Proceedings
- Vol. 1
Numerical Assessment of Enhanced Coatings in Wire Mesh Volumetric Absorbers
Two different wire mesh open volumetric receivers (OVRs) are studied together with six different coatings and two different working conditions in order to assess their effect on the performance of the OVR comparing them to the two baseline OVRs, uncoated and state-of-the-art. The results show that selective coatings produce the best OVR thermal results, having the best results when the solar absorptance is as high as possible and the thermal emittance is as low as possible.
- 16 April 2024
- Published by TIB Open Publishing in SolarPACES Conference Proceedings
- Vol. 1
Open AccessNumerical Assessment of Enhanced Coatings in Wire Mesh Volumetric Absorbers
Two different wire mesh open volumetric receivers (OVRs) are studied together with six different coatings and two different working conditions in order to assess their effect on the performance of the OVR comparing them to the two baseline OVRs, uncoated and state-of-the-art. The results show that selective coatings produce the best OVR thermal results, having the best results when the solar absorptance is as high as possible and the thermal emittance is as low as possible.
- Open Access
- 10 April 2024
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 271
High performance selective solar absorber stable in air for high temperature applications
- 10 April 2024
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 271
Open AccessHigh performance selective solar absorber stable in air for high temperature applications
- Open Access
- 29 December 2023
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 7 (2) , 438-449
Synthesis and Characterization of Multilayered CrAlN/Al2O3 Tandem Coating Using HiPIMS for Solar Selective Applications at High Temperature
The effect of applying a negative bias during deposition of a previously designed multilayer solar selective absorber coating was studied on two types of substrates (316L stainless steel and Inconel 625). The solar selective coating is composed of different chromium aluminum nitride layers deposited using a combination of radiofrequency (RF), direct current (DC), and highpower impulse magnetron sputtering (HiPIMS) technologies. The chemical composition is varied to generate an infrared reflective/ absorber layer (with low Al addition and N vacancies) and two CrAlN intermediate layers with medium and high aluminum content (Al/Cr = 0.6 and 1.2). A top aluminum oxide layer (Al2O3) is deposited as an antireflective layer. In this work, a simultaneous DCpulsed bias (-100 V, 250 kHz) was applied to the substrates in order to increase the film density. The optical performance, thermal stability, and oxidation resistance was evaluated and compared with the performance obtained with similar unbiased coating and a commercial Pyromark paint reference at 600, 700, and 800 degrees C. The coating remained stable after 200 h of annealing at 600 degrees C, with solar absorptance (a) values of 93% and 92% for samples deposited on stainless steel and Inconel, respectively, and a thermal emittance e25 degrees C of 18%. The introduction of additional ion bombardment during film growth through bias assistance resulted in increased durability, thermal stability, and working temperature limits compared with unbiased coatings. The solar-to-mechanical energy conversion efficiency at 800 degrees C was found to be up to 2 times higher than Pyromark at C = 100 and comparable at C = 1000.
- 29 December 2023
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 7 (2) , 438-449
Open AccessSynthesis and Characterization of Multilayered CrAlN/Al2O3 Tandem Coating Using HiPIMS for Solar Selective Applications at High Temperature
The effect of applying a negative bias during deposition of a previously designed multilayer solar selective absorber coating was studied on two types of substrates (316L stainless steel and Inconel 625). The solar selective coating is composed of different chromium aluminum nitride layers deposited using a combination of radiofrequency (RF), direct current (DC), and highpower impulse magnetron sputtering (HiPIMS) technologies. The chemical composition is varied to generate an infrared reflective/ absorber layer (with low Al addition and N vacancies) and two CrAlN intermediate layers with medium and high aluminum content (Al/Cr = 0.6 and 1.2). A top aluminum oxide layer (Al2O3) is deposited as an antireflective layer. In this work, a simultaneous DCpulsed bias (-100 V, 250 kHz) was applied to the substrates in order to increase the film density. The optical performance, thermal stability, and oxidation resistance was evaluated and compared with the performance obtained with similar unbiased coating and a commercial Pyromark paint reference at 600, 700, and 800 degrees C. The coating remained stable after 200 h of annealing at 600 degrees C, with solar absorptance (a) values of 93% and 92% for samples deposited on stainless steel and Inconel, respectively, and a thermal emittance e25 degrees C of 18%. The introduction of additional ion bombardment during film growth through bias assistance resulted in increased durability, thermal stability, and working temperature limits compared with unbiased coatings. The solar-to-mechanical energy conversion efficiency at 800 degrees C was found to be up to 2 times higher than Pyromark at C = 100 and comparable at C = 1000.
- Open Access
- 26 December 2023
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 266
Performance improvement of CSP particle receivers by depositing spinel absorber coatings
- 26 December 2023
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 266
Open AccessPerformance improvement of CSP particle receivers by depositing spinel absorber coatings
- Open Access
- 11 December 2023
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 266
Intercomparison of opto-thermal spectral measurements for concentrating solar thermal receiver materials from room temperature up to 800 °C
- 11 December 2023
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 266
Open AccessIntercomparison of opto-thermal spectral measurements for concentrating solar thermal receiver materials from room temperature up to 800 °C
- Open Access
- 15 September 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 52, 1338-1359
Methanation of CO2 on Cu in a tubular co-ionic SOEC
- 15 September 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 52, 1338-1359
Open AccessMethanation of CO2 on Cu in a tubular co-ionic SOEC
- Open Access
- 6 February 2023
- Published by Elsevier in Solar Energy
- Vol. 252, 134-144
Study of abrasion tests for antireflective and antisoiling/antireflective coatings on glass solar tubes
- 6 February 2023
- Published by Elsevier in Solar Energy
- Vol. 252, 134-144
Open AccessStudy of abrasion tests for antireflective and antisoiling/antireflective coatings on glass solar tubes
- Open Access
A Highly Stable and Sustainable Low-Temperature Selective Absorber: Structural and Ageing Characterisation
Solar absorbers in a three-layer configuration have been prepared by dip-coating onto aluminium substrates. They are constituted by two spinel layers with one silica layer on the top and values of solar absorptance above 0.950 and thermal emittance below 0.04 were obtained. The effects of using different sintering conditions of the upper silica layer on the optical behaviour and durability tests have been studied. Results obtained in accelerated ageing methods, such as thermal stability tests and condensation tests, clearly show that the proposed selective absorber exhibits excellent thermal stability and very good humidity resistance. The results show that the protective action is due not only to the silica layer but also to the alumina layer produced during the absorber preparation. The phase composition of the individual layers was independently confirmed using X-ray diffraction and corroborated by X-ray Photoelectron Spectroscopy. Spinel-like phases were obtained in both the first and second layers. The ageing study shows that the three-layer configuration proposed has a very high potential, in terms of both durability and optical behaviour, for solar thermal low-temperature applications.
Open AccessA Highly Stable and Sustainable Low-Temperature Selective Absorber: Structural and Ageing Characterisation
Solar absorbers in a three-layer configuration have been prepared by dip-coating onto aluminium substrates. They are constituted by two spinel layers with one silica layer on the top and values of solar absorptance above 0.950 and thermal emittance below 0.04 were obtained. The effects of using different sintering conditions of the upper silica layer on the optical behaviour and durability tests have been studied. Results obtained in accelerated ageing methods, such as thermal stability tests and condensation tests, clearly show that the proposed selective absorber exhibits excellent thermal stability and very good humidity resistance. The results show that the protective action is due not only to the silica layer but also to the alumina layer produced during the absorber preparation. The phase composition of the individual layers was independently confirmed using X-ray diffraction and corroborated by X-ray Photoelectron Spectroscopy. Spinel-like phases were obtained in both the first and second layers. The ageing study shows that the three-layer configuration proposed has a very high potential, in terms of both durability and optical behaviour, for solar thermal low-temperature applications.
- 8 November 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2033 (1) , 220006
Antireflective coatings on quartz glass for high temperature solar receivers
Within the Spanish DETECSOL project, antireflective (AR) coatings for quartz windows of solar tower receivers are developed for a more efficient solar thermal technology. The application of this coating on the window, similar to those applied on the glass envelopes of parabolic trough receivers, can decrease the optical losses and therefore increase the receiver efficiency. For these applications, not only the AR coating optical performance is important but also a high temperature and abrasion resistance. In this paper, a silica porous layer from a polymeric solution was prepared and deposited on both sides of a quartz window as an AR coating, increasing the solar transmittance from 0.931 to 0.975. The effect of increasing the heat treatment temperature to 500°C, 600°C and 700°C was studied. The coating thickness and/or the coating porosity decreased as the temperature increased. Moreover, we found that the coating abrasion resistance increased and the coating surface became more reactive as the treatment temperature increased.
- 8 November 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2033 (1) , 220006
Antireflective coatings on quartz glass for high temperature solar receivers
Within the Spanish DETECSOL project, antireflective (AR) coatings for quartz windows of solar tower receivers are developed for a more efficient solar thermal technology. The application of this coating on the window, similar to those applied on the glass envelopes of parabolic trough receivers, can decrease the optical losses and therefore increase the receiver efficiency. For these applications, not only the AR coating optical performance is important but also a high temperature and abrasion resistance. In this paper, a silica porous layer from a polymeric solution was prepared and deposited on both sides of a quartz window as an AR coating, increasing the solar transmittance from 0.931 to 0.975. The effect of increasing the heat treatment temperature to 500°C, 600°C and 700°C was studied. The coating thickness and/or the coating porosity decreased as the temperature increased. Moreover, we found that the coating abrasion resistance increased and the coating surface became more reactive as the treatment temperature increased.