Hiroshi Nakayama
Hiroshi Nakayama has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Hifni Mukhtar Ariyadi
Universitas Gadjah Mada
1 shared publication - Hiroaki Terasaki
Department of Architecture and Civil Engineering, Graduate School of Engineering, University of Fukui, 3-9-1 Bunkyo, Fukui, 910-8507, Japan
1 shared publication - Kiyoshi Saito
Department of Applied Mechanics and Aerospace Engineering, Waseda University, 3-4-1 Okubo, Shinjuku-ku, Tokyo 169-8555, Japan
1 shared publication - Niccolo Giannetti
Department of Mechanical and Intelligent Systems Engineering, The University of Electro-Communications, Tokyo 182-8585, Japan
1 shared publication - Richard Jayson Varela
Graduate School of Fundamental Science and Engineering, Waseda University, Shinjuku-ku 169-8555, Tokyo, Japan
1 shared publication - Seiichi Yamaguchi
Waseda University
1 shared publication
Latest Publications
- 11 February 2026
- Published by Trans Tech Publications, Ltd. in Advances in Science and Technology
- Vol. 173, 147-156
Demonstration of the Snow-Melting and Economic Effects of a Snow-Melting System Using Building Waste Heat
This study investigated the performance and life cycle costs of a snow-melting system that employs waste heat from a building in the Matsunokitouge parking area of Takayama City, Gifu Prefecture. The average center temperature of the interlocking blocks and air temperature inside the pallets in the snowmelt area were 4.8°C and 9°C higher, respectively, than those in the non-snowmelt area during the short-term observation period. Snowmelt occurred in this system when the outdoor temperature was −2°C or higher and the snowfall rate was 2.5 cm/h or lower. The life cycle costs estimated based on the experimental results generally became lower than those of the conventional system within ten years.
- 11 February 2026
- Published by Trans Tech Publications, Ltd. in Advances in Science and Technology
- Vol. 173, 147-156
Demonstration of the Snow-Melting and Economic Effects of a Snow-Melting System Using Building Waste Heat
This study investigated the performance and life cycle costs of a snow-melting system that employs waste heat from a building in the Matsunokitouge parking area of Takayama City, Gifu Prefecture. The average center temperature of the interlocking blocks and air temperature inside the pallets in the snowmelt area were 4.8°C and 9°C higher, respectively, than those in the non-snowmelt area during the short-term observation period. Snowmelt occurred in this system when the outdoor temperature was −2°C or higher and the snowfall rate was 2.5 cm/h or lower. The life cycle costs estimated based on the experimental results generally became lower than those of the conventional system within ten years.
- 6 August 2018
- Published by ASME International in Journal of Fluids Engineering
- Vol. 140 (12)
Semitheoretical Prediction of the Wetting Characteristics of Aqueous Ionic Liquid Solution on an Aluminum Finned-Tube Desiccant Contactor
This study involves exploring a new design of an internally cooled/heated desiccant contactor by using a new ionic liquid (IL) solution as the sorptive solution. In order to optimize its operative performance, a semitheoretical model based on the principle of minimum energy is developed to predict the film rupture and wetting ability of the IL solution over a comprehensive range of IL mass fraction and flow rates. A first experimental validation of the fundamental equations of the theoretical model is presented and used as a reference to minimize deviations between predicted results and measured data by calibrating dedicated characteristic coefficients. The noteworthy quantitative and qualitative agreement in the whole range of IL mass fractions and flow rates is promising for contributing to the design of optimized system configurations and control strategies.
- 6 August 2018
- Published by ASME International in Journal of Fluids Engineering
- Vol. 140 (12)
Semitheoretical Prediction of the Wetting Characteristics of Aqueous Ionic Liquid Solution on an Aluminum Finned-Tube Desiccant Contactor
This study involves exploring a new design of an internally cooled/heated desiccant contactor by using a new ionic liquid (IL) solution as the sorptive solution. In order to optimize its operative performance, a semitheoretical model based on the principle of minimum energy is developed to predict the film rupture and wetting ability of the IL solution over a comprehensive range of IL mass fraction and flow rates. A first experimental validation of the fundamental equations of the theoretical model is presented and used as a reference to minimize deviations between predicted results and measured data by calibrating dedicated characteristic coefficients. The noteworthy quantitative and qualitative agreement in the whole range of IL mass fractions and flow rates is promising for contributing to the design of optimized system configurations and control strategies.