Gonzalo Aguila
Research Subjects
Gonzalo Aguila has a total of 110 co-authors. Here are the top co-authors by number of shared publications:
- Paulo Araya
Universidad de Chile, Santiago, Chile
15 shared publications Sichem Guerrero
12 shared publicationsPaulo Araya
Departamento de Ingeniería Química, Biotecnología y Materiales, Universidad de Chile, Casilla 2777, Santiago, Chile
8 shared publications- Francisco Gracia
Department of Chemical Engineering, Biotechnology and Materials, Faculty of Physical and Mathematical Sciences, Universidad de Chile, Av. Beauchef 851, Santiago 8370456, Chile
5 shared publications P. Baeza
4 shared publications- Sichem Guerrero
Universidad de los Andes, Chile, Facultad de Ingeniería y Ciencias Aplicadas, Monseñor Álvaro del Portillo, 12455 Las Condes, Chile
4 shared publications
Latest Publications
- Open Access
Macrocystis pyrifera Biochar Activated with FeCl2: An Effective and Sustainable Adsorbent for As(V) Removal at Drinking-Water-Relevant Concentrations
Arsenic contamination of drinking water threatens more than 100 million people worldwide, particularly in regions where decentralized, low-cost treatment solutions are urgently needed. Although biochar-based adsorbents have shown promise, the performance of seaweed-derived biochars—especially under environmentally relevant, low arsenic concentrations—remains poorly characterized. Here, we developed and evaluated a Fe-activated biochar derived from the kelp Macrocystis pyrifera for As(V) removal under drinking-water-relevant conditions. Fe activation with FeCl2—rather than textural modification via KOH—was critical for introducing Fe–O surface complexes that governed chemisorption and drove high removal efficiency at low concentrations. The Fe-activated biochar exhibited a BET surface area of 22.23 m2 g−1, a point of zero charge near neutral pH (pHPZC ≈ 6.36), and low ash content ( 0.99), consistent with a strong contribution of surface chemical interactions under the tested conditions. Fe-activated biochar removed 53–67% of As(V) across initial concentrations of 0.01–0.20 mg L−1, approaching an adsorption plateau within 12–20 h, positioning this sustainable, kelp-derived material as a promising candidate for point-of-use arsenic treatment in affected regions.
Open AccessMacrocystis pyrifera Biochar Activated with FeCl2: An Effective and Sustainable Adsorbent for As(V) Removal at Drinking-Water-Relevant Concentrations
Arsenic contamination of drinking water threatens more than 100 million people worldwide, particularly in regions where decentralized, low-cost treatment solutions are urgently needed. Although biochar-based adsorbents have shown promise, the performance of seaweed-derived biochars—especially under environmentally relevant, low arsenic concentrations—remains poorly characterized. Here, we developed and evaluated a Fe-activated biochar derived from the kelp Macrocystis pyrifera for As(V) removal under drinking-water-relevant conditions. Fe activation with FeCl2—rather than textural modification via KOH—was critical for introducing Fe–O surface complexes that governed chemisorption and drove high removal efficiency at low concentrations. The Fe-activated biochar exhibited a BET surface area of 22.23 m2 g−1, a point of zero charge near neutral pH (pHPZC ≈ 6.36), and low ash content ( 0.99), consistent with a strong contribution of surface chemical interactions under the tested conditions. Fe-activated biochar removed 53–67% of As(V) across initial concentrations of 0.01–0.20 mg L−1, approaching an adsorption plateau within 12–20 h, positioning this sustainable, kelp-derived material as a promising candidate for point-of-use arsenic treatment in affected regions.
- Open Access
Second-Pass Vessel Arrangement and Separation-Limited Operation in Two-Pass Seawater Reverse Osmosis Under Progressive Fouling: Implications for Electrolytic Hydrogen Production
Seawater reverse osmosis (SWRO) supplies the purification chain of electrolytic hydrogen plants, yet its long-term behaviour under fouling is rarely resolved at train level. This work presents a dynamic, quasi-steady-state model of a two-pass SWRO train and compares three second-pass architectures under progressive first-pass fouling, represented by time-evolving water- and solute-permeability coefficients. At each of 51 instants over a 500-day horizon, the operating point is re-optimized to minimize specific energy consumption (SEC), subject to a product limit of 20 mg·L−1 set by the downstream polishing stage rather than the electrolyzer. Two share-membrane types, element count and installed area, differ only in vessel arrangement; the third is the industrial reference. Arrangement alone changes SEC by 36.9–41.6% across three fouling scenarios, 8.38 against 11.46 kWh·m−3 under severe fouling, widening to 71% at fixed production. Fouling constrains the system through separation, not hydraulics: the technically admissible operating window widens as membranes degrade, whereas the window satisfying the product specification closes. The energy penalty of compliance begins at days 310 and 170, respectively, accumulating about twice as fast thereafter in the former. Energy recovery reduces SEC by 63–64% without altering the ordering.
Open AccessSecond-Pass Vessel Arrangement and Separation-Limited Operation in Two-Pass Seawater Reverse Osmosis Under Progressive Fouling: Implications for Electrolytic Hydrogen Production
Seawater reverse osmosis (SWRO) supplies the purification chain of electrolytic hydrogen plants, yet its long-term behaviour under fouling is rarely resolved at train level. This work presents a dynamic, quasi-steady-state model of a two-pass SWRO train and compares three second-pass architectures under progressive first-pass fouling, represented by time-evolving water- and solute-permeability coefficients. At each of 51 instants over a 500-day horizon, the operating point is re-optimized to minimize specific energy consumption (SEC), subject to a product limit of 20 mg·L−1 set by the downstream polishing stage rather than the electrolyzer. Two share-membrane types, element count and installed area, differ only in vessel arrangement; the third is the industrial reference. Arrangement alone changes SEC by 36.9–41.6% across three fouling scenarios, 8.38 against 11.46 kWh·m−3 under severe fouling, widening to 71% at fixed production. Fouling constrains the system through separation, not hydraulics: the technically admissible operating window widens as membranes degrade, whereas the window satisfying the product specification closes. The energy penalty of compliance begins at days 310 and 170, respectively, accumulating about twice as fast thereafter in the former. Energy recovery reduces SEC by 63–64% without altering the ordering.
- Open Access
- 23 June 2026
- Published by Elsevier in SSRN Electronic Journal
Dynamic modeling of two-pass seawater reverse osmosis configurations under progressive fouling: a trade-off between specific energy consumption and operational viability for green hydrogen
Producing PEM-grade water for green hydrogen via seawater reverse osmosis (SWRO) requires multi-pass trains whose performance degrades as membranes foul, yet the influence of train architecture on this degradation remains poorly characterized. This work presents a dynamic, quasi-steady-state model of a two-pass SWRO system that tracks the coupled evolution of water (A) and solute (B) permeability under progressive fouling over a 500-day horizon, and uses it to compare two second-pass architectures: a series configuration (C1) and a parallel-plus-series configuration (C2). At each time step, the operating point is re-optimized to minimize the specific energy consumption (SEC) subject to a PEM product-quality limit, under three fouling-severity scenarios derived from long-term field data. The two configurations are nearly identical when clean (SEC ≈ 7.5–7.6 kWh·m⁻³) but diverge as fouling advances: C1 rises to 10.5 kWh·m⁻³ under severe fouling, whereas C2 stays near 7.7 kWh·m⁻³, because the parallel first stage of C2 moderates the pressure escalation that fouling imposes. This efficiency advantage, however, is accompanied by reduced robustness: under severe fouling, C2 reaches a technical feasibility limit before the end of the horizon, whereas C1 sustains feasible operation throughout. The results reveal a structural trade-off between energy efficiency and operational robustness that static or single-configuration models cannot capture, and that persists with or without energy recovery. The framework provides design guidance for integrated desalination–electrolysis hubs, indicating when efficiency or resilience should govern the choice of SWRO architecture.
- 23 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDynamic modeling of two-pass seawater reverse osmosis configurations under progressive fouling: a trade-off between specific energy consumption and operational viability for green hydrogen
Producing PEM-grade water for green hydrogen via seawater reverse osmosis (SWRO) requires multi-pass trains whose performance degrades as membranes foul, yet the influence of train architecture on this degradation remains poorly characterized. This work presents a dynamic, quasi-steady-state model of a two-pass SWRO system that tracks the coupled evolution of water (A) and solute (B) permeability under progressive fouling over a 500-day horizon, and uses it to compare two second-pass architectures: a series configuration (C1) and a parallel-plus-series configuration (C2). At each time step, the operating point is re-optimized to minimize the specific energy consumption (SEC) subject to a PEM product-quality limit, under three fouling-severity scenarios derived from long-term field data. The two configurations are nearly identical when clean (SEC ≈ 7.5–7.6 kWh·m⁻³) but diverge as fouling advances: C1 rises to 10.5 kWh·m⁻³ under severe fouling, whereas C2 stays near 7.7 kWh·m⁻³, because the parallel first stage of C2 moderates the pressure escalation that fouling imposes. This efficiency advantage, however, is accompanied by reduced robustness: under severe fouling, C2 reaches a technical feasibility limit before the end of the horizon, whereas C1 sustains feasible operation throughout. The results reveal a structural trade-off between energy efficiency and operational robustness that static or single-configuration models cannot capture, and that persists with or without energy recovery. The framework provides design guidance for integrated desalination–electrolysis hubs, indicating when efficiency or resilience should govern the choice of SWRO architecture.
- 1 May 2026
- Published by Springer Nature
- p. 219-232
Data‑Driven and Experimental Validation of Aerodynamic Efficiency Strategies for Heavy‑Duty Trucks in Chile
- 1 May 2026
- Published by Springer Nature
- p. 219-232
Data‑Driven and Experimental Validation of Aerodynamic Efficiency Strategies for Heavy‑Duty Trucks in Chile
- Open Access
- 15 October 2025
- Published by Elsevier in Industrial Crops and Products
- Vol. 236
Unlocking the potential of eugenol-coformer co-amorphous pairs in active packaging designed for the controlled release and enhanced antibacterial activity
- 15 October 2025
- Published by Elsevier in Industrial Crops and Products
- Vol. 236
Open AccessUnlocking the potential of eugenol-coformer co-amorphous pairs in active packaging designed for the controlled release and enhanced antibacterial activity
- 11 June 2025
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 222
Fueling the transition: A comprehensive analysis of hydrogen roadmaps in Chile, Brazil and Colombia
- 11 June 2025
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 222
Fueling the transition: A comprehensive analysis of hydrogen roadmaps in Chile, Brazil and Colombia
- Open Access
- 21 September 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (39) , 40394-40410
Calcium-Poison-Resistant Cu/YCeO2–TiO2 Catalyst for the Selective Catalytic Reduction of NO with CO and Naphthalene in the Presence of Oxygen
The pollution from industrial processes based on biomass combustion is still an ongoing problem. In the present contribution, the selective catalytic reduction of NO with CO and naphthalene is carried out in the presence of 10% oxygen. The accumulation of alkaline and alkaline earth metals during biomass combustion is here simulated by the addition of calcium to a Cu-impregnated YCeO2–TiO2 support. The results show that a high dispersion of copper is obtained, which is resistant to the accumulation of calcium. Full conversion of CO and naphthalene is achieved above 200 °C, whereas NO conversions of 80, 90, and 87% are obtained for the catalysts with Ca loadings of 2.6, 5.2, and 13%, respectively, at 350 °C. It is proposed that the high activity of the catalysts is ascribed to the formation of Cu–Ox–Ce species and that the accumulation of Ca acts as a barrier to avoid copper sintering. It was found that different forms of carbonate and nitrite/nitrate species form during reaction, coexisting as adsorbed species during the SCR reaction. The selectivity to N2 was almost 100% in all cases, due to the small presence of NO2 in the reactor outlet (no N2O was detected in any conditions).
- 21 September 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (39) , 40394-40410
Open AccessCalcium-Poison-Resistant Cu/YCeO2–TiO2 Catalyst for the Selective Catalytic Reduction of NO with CO and Naphthalene in the Presence of Oxygen
The pollution from industrial processes based on biomass combustion is still an ongoing problem. In the present contribution, the selective catalytic reduction of NO with CO and naphthalene is carried out in the presence of 10% oxygen. The accumulation of alkaline and alkaline earth metals during biomass combustion is here simulated by the addition of calcium to a Cu-impregnated YCeO2–TiO2 support. The results show that a high dispersion of copper is obtained, which is resistant to the accumulation of calcium. Full conversion of CO and naphthalene is achieved above 200 °C, whereas NO conversions of 80, 90, and 87% are obtained for the catalysts with Ca loadings of 2.6, 5.2, and 13%, respectively, at 350 °C. It is proposed that the high activity of the catalysts is ascribed to the formation of Cu–Ox–Ce species and that the accumulation of Ca acts as a barrier to avoid copper sintering. It was found that different forms of carbonate and nitrite/nitrate species form during reaction, coexisting as adsorbed species during the SCR reaction. The selectivity to N2 was almost 100% in all cases, due to the small presence of NO2 in the reactor outlet (no N2O was detected in any conditions).
- 18 March 2024
- Published by Springer Nature
- p. 607-615
Mixed Integer Linear Programming for Solving Time–Cost Trade-Off Problem of Infrastructure Project
- 18 March 2024
- Published by Springer Nature
- p. 607-615
Mixed Integer Linear Programming for Solving Time–Cost Trade-Off Problem of Infrastructure Project
- 29 February 2024
- Published by Springer Nature
- p. 413-424
Design of a Generic Simulation Model of Direct and Reverse Logistics of PET Plastic Focused to Mitigation of Negative Impacts on Retailers
- 29 February 2024
- Published by Springer Nature
- p. 413-424
Design of a Generic Simulation Model of Direct and Reverse Logistics of PET Plastic Focused to Mitigation of Negative Impacts on Retailers
- Open Access
- 16 November 2023
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 13 (48) , 34210-34223
Improving and measuring the solubility of favipiravir and montelukast in SC-CO 2 with ethanol projecting their nanonization
Improving and measuring the solubility of favipiravir and montelukast in SC-CO 2 with ethanol projecting their nanonization.
- 16 November 2023
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 13 (48) , 34210-34223
Open AccessImproving and measuring the solubility of favipiravir and montelukast in SC-CO 2 with ethanol projecting their nanonization
Improving and measuring the solubility of favipiravir and montelukast in SC-CO 2 with ethanol projecting their nanonization.