Alp Zibil
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Alp Zibil has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Flavio Firmani
2 shared publications- Flavio Firmani
University of Victoria
1 shared publication Ron P. Podhorodeski
University of Victoria, Victoria, BC, Canada
1 shared publication- Ron P. Podhorodeski
Robotics and Mechanisms Laboratory, Department of Mechanical Engineering, University of Victoria, P. O. Box 3055, Victoria, B. C, V8W 3P6, Canada
1 shared publication Ronald P.
1 shared publicationScott B.
1 shared publication
Latest Publications
- Open Access
- 1 April 2008
- Published by IntechOpen
Wrench Capabilities of Planar Parallel Manipulators and their Effects Under Redundancy
- 1 April 2008
- Published by IntechOpen
Open AccessWrench Capabilities of Planar Parallel Manipulators and their Effects Under Redundancy
- 1 December 2007
- Published by Canadian Science Publishing in Transactions of the Canadian Society for Mechanical Engineering
- Vol. 31 (4) , 469-481
FORCE-MOMENT CAPABILITIES OF REVOLUTE-JOINTED PLANAR PARALLEL MANIPULATORS WITH ADDITIONAL ACTUATED BRANCHES
The force-moment capabilities of revolute-jointed planar parallel manipulators (PPMs) are presented. A previously developed analysis that determines explicitly the force-moment capabilities of parallel manipulators is considered and the formulation is improved. This analysis is based upon properly adjusting the actuator outputs to their maximum capabilities. The force-moment capabilities of two actuation layouts are investigated: the non-redundant 3-RRR PPM and the redundantly actuated 4-RRR PPM, where the underline indicates the actuated joint. Four studies of force-moment capabilities are presented: maximum force with a prescribed moment, maximum applicable force, maximum moment with a prescribed force, and maximum applicable moment. These studies are performed for constant payload orientation of the mobile platform throughout the manipulator’s workspace. It is concluded that the manipulator with the additional actuated branch shows an improvement of the force-moment capabilities at the expense of reducing its workspace.
- 1 December 2007
- Published by Canadian Science Publishing in Transactions of the Canadian Society for Mechanical Engineering
- Vol. 31 (4) , 469-481
FORCE-MOMENT CAPABILITIES OF REVOLUTE-JOINTED PLANAR PARALLEL MANIPULATORS WITH ADDITIONAL ACTUATED BRANCHES
The force-moment capabilities of revolute-jointed planar parallel manipulators (PPMs) are presented. A previously developed analysis that determines explicitly the force-moment capabilities of parallel manipulators is considered and the formulation is improved. This analysis is based upon properly adjusting the actuator outputs to their maximum capabilities. The force-moment capabilities of two actuation layouts are investigated: the non-redundant 3-RRR PPM and the redundantly actuated 4-RRR PPM, where the underline indicates the actuated joint. Four studies of force-moment capabilities are presented: maximum force with a prescribed moment, maximum applicable force, maximum moment with a prescribed force, and maximum applicable moment. These studies are performed for constant payload orientation of the mobile platform throughout the manipulator’s workspace. It is concluded that the manipulator with the additional actuated branch shows an improvement of the force-moment capabilities at the expense of reducing its workspace.
- 1 January 2007
- Published by ASME International
- p. 1013-1020
An Analysis of the Force-Moment Capabilities of Branch-Redundant Planar-Parallel Manipulators
The force-moment capabilities of branch-redundant planar-parallel manipulators (PPMs) are investigated. A previously developed explicit methodology for generating the force-moment capabilities of redundant PPMs is used on three different PPM architectures. The results for the 4-RRR, 4-RPR, 4-PRR layouts (where the underline denotes the actuated joint in each branch) are presented and discussed. For the revolute-actuated layouts, it was shown that the force-moment capabilities for the 4-RRR were in general better than those of the 4-RPR for the chosen manipulator parameters. The presented analysis is an effective tool for designing PPMs to determine the largest forces and moments that can be applied at any point within the workspace.
- 1 January 2007
- Published by ASME International
- p. 1013-1020
An Analysis of the Force-Moment Capabilities of Branch-Redundant Planar-Parallel Manipulators
The force-moment capabilities of branch-redundant planar-parallel manipulators (PPMs) are investigated. A previously developed explicit methodology for generating the force-moment capabilities of redundant PPMs is used on three different PPM architectures. The results for the 4-RRR, 4-RPR, 4-PRR layouts (where the underline denotes the actuated joint in each branch) are presented and discussed. For the revolute-actuated layouts, it was shown that the force-moment capabilities for the 4-RRR were in general better than those of the 4-RPR for the chosen manipulator parameters. The presented analysis is an effective tool for designing PPMs to determine the largest forces and moments that can be applied at any point within the workspace.