Morgan Bazilian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Morgan Bazilian has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Mikhail Zhizhin
Payne Institute for Public Policy, Colorado School of Mines, Golden, CO 80401, USA
12 shared publications - Christopher D. Elvidge
Payne Institute for Public Policy, Colorado School of Mines, Golden, CO 80401, USA
11 shared publications - Tilottama Ghosh
Payne Institute for Public Policy, Colorado School of Mines, Golden, CO 80401, USA
10 shared publications - Feng-Chi Hsu
Earth Observation Group, Payne Institute for Public Policy, Colorado School of Mines, Golden, CO 80401, USA
4 shared publications - Gregory Gleason
Payne Institute for Public Policy, Colorado School of Mines, Golden, CO 80401, USA
4 shared publications - Mark Howells
Loughborough University
4 shared publications
Latest Publications
- Open Access
- 13 November 2026
- Published by MDPI AG in Remote Sensing
- Vol. 18 (22) , 3909
From Site-Level Detections to Monthly and Annual National Totals: Multiyear VIIRS Nightfire Estimates of Global Gas Flaring
This study advances global gas-flaring monitoring from a sequence of annual inventories to a monthly, source-resolved, multi-satellite record of upstream gas flaring from March 2012 through December 2025, using VIIRS Nightfire observations from SNPP, NOAA-20, and NOAA-21. The analysis integrates a persistent multiyear flare catalog, a calibration derived from controlled flare tests relating radiant heat to gas flow rate, and an aggregation framework that separates clear non-detections from cloud-affected, sunlit, or otherwise invalid observations. The framework yields consistent monthly and annual estimates from individual flare sites to country and global scales. Global upstream flaring reached 164.5 BCM in 2025, the third consecutive annual increase, and was highly concentrated: 4.3% of active sites accounted for 80% of the global volume. Summed monthly estimates are internally consistent with direct annual estimates (median ratio 98.1%) while revealing seasonal patterns and short-term changes hidden in annual inventories. Global estimates from the three VIIRS instruments agree within 1–4%, and comparisons with regulatory records for Texas (Permian and Eagle Ford) and New Mexico, regions with reliable reporting but atypically small and intermittent flares, show strong temporal agreement (monthly r = 0.85–0.91) and recovery of 69–93% of reported volumes. Comparisons with legacy estimates further show that differences among flaring products reflect combined changes in source coverage, calibration, satellite sampling, and aggregation rather than a uniform rescaling of annual totals. Cloud-covered overpasses must be excluded rather than counted as non-detections, which would lower global volumes by 27–30%, and the catalog must be refreshed every 6–12 months to remain representative.
- 13 November 2026
- Published by MDPI AG in Remote Sensing
- Vol. 18 (22) , 3909
Open AccessFrom Site-Level Detections to Monthly and Annual National Totals: Multiyear VIIRS Nightfire Estimates of Global Gas Flaring
This study advances global gas-flaring monitoring from a sequence of annual inventories to a monthly, source-resolved, multi-satellite record of upstream gas flaring from March 2012 through December 2025, using VIIRS Nightfire observations from SNPP, NOAA-20, and NOAA-21. The analysis integrates a persistent multiyear flare catalog, a calibration derived from controlled flare tests relating radiant heat to gas flow rate, and an aggregation framework that separates clear non-detections from cloud-affected, sunlit, or otherwise invalid observations. The framework yields consistent monthly and annual estimates from individual flare sites to country and global scales. Global upstream flaring reached 164.5 BCM in 2025, the third consecutive annual increase, and was highly concentrated: 4.3% of active sites accounted for 80% of the global volume. Summed monthly estimates are internally consistent with direct annual estimates (median ratio 98.1%) while revealing seasonal patterns and short-term changes hidden in annual inventories. Global estimates from the three VIIRS instruments agree within 1–4%, and comparisons with regulatory records for Texas (Permian and Eagle Ford) and New Mexico, regions with reliable reporting but atypically small and intermittent flares, show strong temporal agreement (monthly r = 0.85–0.91) and recovery of 69–93% of reported volumes. Comparisons with legacy estimates further show that differences among flaring products reflect combined changes in source coverage, calibration, satellite sampling, and aggregation rather than a uniform rescaling of annual totals. Cloud-covered overpasses must be excluded rather than counted as non-detections, which would lower global volumes by 27–30%, and the catalog must be refreshed every 6–12 months to remain representative.
- Open Access
- 13 October 2026
- Published by MDPI AG in Preprints.org
From Site-Level Detections to Monthly and Annual National Totals: Multiyear VIIRS Nightfire Estimates of Global Gas Flaring
This study advances global gas-flaring monitoring from a sequence of annual inventories to a monthly, source-resolved, multi-satellite record of upstream gas flaring from March 2012 through December 2025, using VIIRS Nightfire observations from SNPP, NOAA-20, and NOAA-21. The analysis integrates a persistent multiyear flare catalog, a calibration derived from controlled flare tests relating radiant heat to gas flow rate, and an aggregation framework that separates clear non-detections from cloud-affected, sunlit, or otherwise invalid observations. The framework yields consistent monthly and annual estimates from individual flare sites to country and global scales. Global upstream flaring reached 164.5 BCM in 2025, the third consecutive annual increase, and was highly concentrated: 4.3% of active sites accounted for 80% of the global volume. Summed monthly estimates are internally consistent with direct annual estimates (median ratio 98.1%) while revealing seasonal patterns and short-term changes hidden in annual inventories. Global estimates from the three VIIRS instruments agree within 1–4%, and comparisons with regulatory records for Texas (Permian and Eagle Ford) and New Mexico, regions with reliable reporting but atypically small and intermittent flares, show strong temporal agreement (monthly r = 0.85–0.91) and recovery of 69–96% of reported volumes. Comparisons with legacy estimates further show that differences among flaring products reflect combined changes in source coverage, calibration, satellite sampling, and aggregation rather than a uniform rescaling of annual totals. Cloud-covered overpasses must be excluded rather than counted as non-detections, which would lower global volumes by 27–30%, and the catalog must be refreshed every 6–12 months to remain representative.
- 13 October 2026
- Published by MDPI AG in Preprints.org
Open AccessFrom Site-Level Detections to Monthly and Annual National Totals: Multiyear VIIRS Nightfire Estimates of Global Gas Flaring
This study advances global gas-flaring monitoring from a sequence of annual inventories to a monthly, source-resolved, multi-satellite record of upstream gas flaring from March 2012 through December 2025, using VIIRS Nightfire observations from SNPP, NOAA-20, and NOAA-21. The analysis integrates a persistent multiyear flare catalog, a calibration derived from controlled flare tests relating radiant heat to gas flow rate, and an aggregation framework that separates clear non-detections from cloud-affected, sunlit, or otherwise invalid observations. The framework yields consistent monthly and annual estimates from individual flare sites to country and global scales. Global upstream flaring reached 164.5 BCM in 2025, the third consecutive annual increase, and was highly concentrated: 4.3% of active sites accounted for 80% of the global volume. Summed monthly estimates are internally consistent with direct annual estimates (median ratio 98.1%) while revealing seasonal patterns and short-term changes hidden in annual inventories. Global estimates from the three VIIRS instruments agree within 1–4%, and comparisons with regulatory records for Texas (Permian and Eagle Ford) and New Mexico, regions with reliable reporting but atypically small and intermittent flares, show strong temporal agreement (monthly r = 0.85–0.91) and recovery of 69–96% of reported volumes. Comparisons with legacy estimates further show that differences among flaring products reflect combined changes in source coverage, calibration, satellite sampling, and aggregation rather than a uniform rescaling of annual totals. Cloud-covered overpasses must be excluded rather than counted as non-detections, which would lower global volumes by 27–30%, and the catalog must be refreshed every 6–12 months to remain representative.
- Open Access
- 16 January 2026
- Published by MDPI AG in Remote Sensing
- Vol. 18 (2) , 314
VIIRS Nightfire Super-Resolution Method for Multiyear Cataloging of Natural Gas Flaring Sites: 2012-2025
We present a new method for mapping global gas flaring using a multiyear spatio-temporal database of VIIRS Nightfire (VNF) nighttime infrared detections from the Suomi NPP, NOAA-20, and NOAA-21 satellites. The method is designed to resolve closely spaced industrial combustion sources and to produce a stable, physically meaningful flare catalog suitable for long-term monitoring and emissions analysis. The method combines adaptive spatial aggregation of high-temperature detections with a hierarchical clustering that super-resolves individual flare stacks within oil and gas fields. Post-processing yields physically consistent flare footprints and attraction regions, allowing separation of closely spaced sources. Flare clusters are assigned to operational categories (e.g., upstream, midstream, LNG) using prior catalogs combined with AI-assisted expert interpretation. In this step, a multimodal large language model (LLM) provides contextual classification suggestions based on geospatial information, high-resolution daytime imagery, and detection time-series summaries, while final attribution is performed and validated by domain experts. Compared with annual flare catalogs commonly used for national flaring estimates, the new catalog demonstrates substantially improved performance. It is more selective in the presence of intense atmospheric glow from large flares, identifies approximately twice as many active flares, and localizes individual stacks with ~50 m precision, resolving emitters separated by ~400–700 m. For the well-defined class of downstream flares at LNG export facilities, the catalog achieves complete detectability. These improvements support more accurate flare inventories, facility-level attribution, and policy-relevant assessments of gas flaring activity.
- 16 January 2026
- Published by MDPI AG in Remote Sensing
- Vol. 18 (2) , 314
Open AccessVIIRS Nightfire Super-Resolution Method for Multiyear Cataloging of Natural Gas Flaring Sites: 2012-2025
We present a new method for mapping global gas flaring using a multiyear spatio-temporal database of VIIRS Nightfire (VNF) nighttime infrared detections from the Suomi NPP, NOAA-20, and NOAA-21 satellites. The method is designed to resolve closely spaced industrial combustion sources and to produce a stable, physically meaningful flare catalog suitable for long-term monitoring and emissions analysis. The method combines adaptive spatial aggregation of high-temperature detections with a hierarchical clustering that super-resolves individual flare stacks within oil and gas fields. Post-processing yields physically consistent flare footprints and attraction regions, allowing separation of closely spaced sources. Flare clusters are assigned to operational categories (e.g., upstream, midstream, LNG) using prior catalogs combined with AI-assisted expert interpretation. In this step, a multimodal large language model (LLM) provides contextual classification suggestions based on geospatial information, high-resolution daytime imagery, and detection time-series summaries, while final attribution is performed and validated by domain experts. Compared with annual flare catalogs commonly used for national flaring estimates, the new catalog demonstrates substantially improved performance. It is more selective in the presence of intense atmospheric glow from large flares, identifies approximately twice as many active flares, and localizes individual stacks with ~50 m precision, resolving emitters separated by ~400–700 m. For the well-defined class of downstream flares at LNG export facilities, the catalog achieves complete detectability. These improvements support more accurate flare inventories, facility-level attribution, and policy-relevant assessments of gas flaring activity.
- Open Access
- 3 November 2025
- Published by MDPI AG in Preprints.org
VIIRS Nightfire Super-Resolution Method for Multiyear Cataloging of Natural Gas Flaring Sites: 2012–2025
We present a new method for mapping of gas flares in the multiyear spatio-temporal database of the VIIRS Nightfire (VNF) nighttime infrared heat source detections from the three satellites, Suomi NPP, NOAA-20 and NOAA-21. The algorithm is composed of several steps: (i) 2D histogram binning of the high temperature (>1200 K) detection counts into 15 arcsec latitude-longitude grid, (ii) segmenting of the counts histogram into oil-field sized watershed features that serve as a guide where to search for the VNF detection clusters, (iii) super-resolution clustering the cloud of detections within each feature into a Dirichlet process variational Bayesian Gaussian mixture of compact clusters centered at the location of individual flare stacks, (iv) post-processing of the detected flares to avoid over-splitting and to find flare attraction contours with Voronoi/Apollonius geometry, (v) classification of the detection clusters into a pre-defined categories such as upstream, midstream, LNG, etc. with provenance from the earlier flare catalogs and multimodal LLM reasoning. The AI-assisted classifier uses reverse geocoding of the IR-emitter coordinates, high-definition daytime satellite imagery and time history profiles of the detections inside attraction contours to hint the expert with a probable category of the emitter together with the short summary of reasoning. Compared to the annual catalogs used for the country-level estimates of flared gas volume, the new algorithm is robust to atmospheric glow from large flares (higher selectivity) results in twice the number of the active flares (higher sensitivity), located with subpixels precision ~50 m and separable within ~400-700 m. For the well-defined class of downstream flares at export LNG locations the catalog demonstrates near-complete detectability.
- 3 November 2025
- Published by MDPI AG in Preprints.org
Open AccessVIIRS Nightfire Super-Resolution Method for Multiyear Cataloging of Natural Gas Flaring Sites: 2012–2025
We present a new method for mapping of gas flares in the multiyear spatio-temporal database of the VIIRS Nightfire (VNF) nighttime infrared heat source detections from the three satellites, Suomi NPP, NOAA-20 and NOAA-21. The algorithm is composed of several steps: (i) 2D histogram binning of the high temperature (>1200 K) detection counts into 15 arcsec latitude-longitude grid, (ii) segmenting of the counts histogram into oil-field sized watershed features that serve as a guide where to search for the VNF detection clusters, (iii) super-resolution clustering the cloud of detections within each feature into a Dirichlet process variational Bayesian Gaussian mixture of compact clusters centered at the location of individual flare stacks, (iv) post-processing of the detected flares to avoid over-splitting and to find flare attraction contours with Voronoi/Apollonius geometry, (v) classification of the detection clusters into a pre-defined categories such as upstream, midstream, LNG, etc. with provenance from the earlier flare catalogs and multimodal LLM reasoning. The AI-assisted classifier uses reverse geocoding of the IR-emitter coordinates, high-definition daytime satellite imagery and time history profiles of the detections inside attraction contours to hint the expert with a probable category of the emitter together with the short summary of reasoning. Compared to the annual catalogs used for the country-level estimates of flared gas volume, the new algorithm is robust to atmospheric glow from large flares (higher selectivity) results in twice the number of the active flares (higher sensitivity), located with subpixels precision ~50 m and separable within ~400-700 m. For the well-defined class of downstream flares at export LNG locations the catalog demonstrates near-complete detectability.
- Open Access
An Improved Calibration for Satellite Estimation of Flared Gas Volumes from VIIRS Nighttime Data
The VIIRS Nightfire (VNF) data product is particularly useful for monitoring of global natural gas flaring and estimation of flared gas volumes. Advantages of VIIRS include the collection of nightly global coverage with the inclusion of four daytime channels in the near and shortwave infrared that cover the wavelengths of peak radiant emissions from flares. VNF calculates flare temperatures, source areas, and radiant heat using physical laws. For more than a decade, the Earth Observation Group has estimated flared gas volumes based on radiant heat with a calibration based on reported annual flared and vented natural gas volumes from Cedigaz. The calibration was tuned with an exponent of 0.7 placed on the VNF source areas to achieve the highest regression correlation coefficient. The Cedigaz calibration has wide error bars attributed to unresolvable reporting errors in the Cedigaz data. In this paper we report on the development of an empirical calibration for estimating flared gas volumes based on VIIRS observations of flares running at low, medium, and high flared gas volumes. Tests were run with both single and double flares, with and without atmospheric correction. The new calibrations were applied to VIIRS detection profiles for metered flares located in the North Sea, Arabian Peninsula, and Gulf of Mexico. The results indicate the following: (1) the exponent is unnecessary and causes flared gas volumes to be overestimated for small flares and underestimated for large flares, (2) the calibration can be applied to sites having either single or multiple flares, and (3) flared gas volume estimates can be improved by applying an atmospheric correction to account for regional difference in band-specific transmissivity levels. The new calibration has a prediction interval (error bars) seventy times smaller than the Cedigaz calibration.
Open AccessAn Improved Calibration for Satellite Estimation of Flared Gas Volumes from VIIRS Nighttime Data
The VIIRS Nightfire (VNF) data product is particularly useful for monitoring of global natural gas flaring and estimation of flared gas volumes. Advantages of VIIRS include the collection of nightly global coverage with the inclusion of four daytime channels in the near and shortwave infrared that cover the wavelengths of peak radiant emissions from flares. VNF calculates flare temperatures, source areas, and radiant heat using physical laws. For more than a decade, the Earth Observation Group has estimated flared gas volumes based on radiant heat with a calibration based on reported annual flared and vented natural gas volumes from Cedigaz. The calibration was tuned with an exponent of 0.7 placed on the VNF source areas to achieve the highest regression correlation coefficient. The Cedigaz calibration has wide error bars attributed to unresolvable reporting errors in the Cedigaz data. In this paper we report on the development of an empirical calibration for estimating flared gas volumes based on VIIRS observations of flares running at low, medium, and high flared gas volumes. Tests were run with both single and double flares, with and without atmospheric correction. The new calibrations were applied to VIIRS detection profiles for metered flares located in the North Sea, Arabian Peninsula, and Gulf of Mexico. The results indicate the following: (1) the exponent is unnecessary and causes flared gas volumes to be overestimated for small flares and underestimated for large flares, (2) the calibration can be applied to sites having either single or multiple flares, and (3) flared gas volume estimates can be improved by applying an atmospheric correction to account for regional difference in band-specific transmissivity levels. The new calibration has a prediction interval (error bars) seventy times smaller than the Cedigaz calibration.
- Open Access
- 2 April 2024
- Published by MDPI AG in Atmosphere
- Vol. 15 (4) , 438
Exploring the Hidden World of Lighting Flicker with a High-Speed Camera
Alternating current can result in flickering—or pulsing—in the brightness of light emitted by luminaires. Lighting flicker typically occurs in the range of 100 to 140 cycles per second (Hz), which is too fast for visual perception by most organisms. However, evidence indicates that many organisms perceive flicker with non-visual photoreceptors present on the retinas. Exposure to flickering lights at night disrupts the circadian rhythm of organisms, leading to symptoms similar to blue light exposure at night. The traditional method for detecting flickering is with a flickermeter held near a single light. In this paper, we explore the use of high-speed camera data in the collection of temporal profiles for groups of luminaires simultaneously at distances ranging from several meters to several kilometers. Temporal profiles are extracted for individual lighting features and the full scene. The identification of luminaire types is based on their spectral signatures. With the camera data, it is possible to identify flickering and non-flickering lights, to determine the flicker frequency, to calculate percent flicker and the flicker index, and to identify groups of lights whose flickers are synchronized. Both flickering and non-flickering luminaires can be found for LED, metal halide, fluorescent, and compact fluorescent lights. To date, flickering has been detected in all of the incandescent, high-pressure sodium, and low-pressure sodium luminaires that we measured. We found that flicker synchronization is often present for lights installed within a single facility and also for strings of streetlights. We also found that flicker exposure can come from the light reflected off of the earth’s surface. Luminaires designed to illuminate large areas often saturate high-speed camera data collection. This saturation can be reduced or eliminated using neutral density filters on the camera. Published experimental data on the impacts of flicker on organisms remains sparse. Many studies have drawn inferences on the impacts of spectral and lighting brightness on organisms without controlling for flicker. Our conclusion is that lighting flicker is a type of light pollution. The use of high-speed camera data makes it easier to include flicker as a variable in studies regarding the impacts of lighting on organisms.
- 2 April 2024
- Published by MDPI AG in Atmosphere
- Vol. 15 (4) , 438
Open AccessExploring the Hidden World of Lighting Flicker with a High-Speed Camera
Alternating current can result in flickering—or pulsing—in the brightness of light emitted by luminaires. Lighting flicker typically occurs in the range of 100 to 140 cycles per second (Hz), which is too fast for visual perception by most organisms. However, evidence indicates that many organisms perceive flicker with non-visual photoreceptors present on the retinas. Exposure to flickering lights at night disrupts the circadian rhythm of organisms, leading to symptoms similar to blue light exposure at night. The traditional method for detecting flickering is with a flickermeter held near a single light. In this paper, we explore the use of high-speed camera data in the collection of temporal profiles for groups of luminaires simultaneously at distances ranging from several meters to several kilometers. Temporal profiles are extracted for individual lighting features and the full scene. The identification of luminaire types is based on their spectral signatures. With the camera data, it is possible to identify flickering and non-flickering lights, to determine the flicker frequency, to calculate percent flicker and the flicker index, and to identify groups of lights whose flickers are synchronized. Both flickering and non-flickering luminaires can be found for LED, metal halide, fluorescent, and compact fluorescent lights. To date, flickering has been detected in all of the incandescent, high-pressure sodium, and low-pressure sodium luminaires that we measured. We found that flicker synchronization is often present for lights installed within a single facility and also for strings of streetlights. We also found that flicker exposure can come from the light reflected off of the earth’s surface. Luminaires designed to illuminate large areas often saturate high-speed camera data collection. This saturation can be reduced or eliminated using neutral density filters on the camera. Published experimental data on the impacts of flicker on organisms remains sparse. Many studies have drawn inferences on the impacts of spectral and lighting brightness on organisms without controlling for flicker. Our conclusion is that lighting flicker is a type of light pollution. The use of high-speed camera data makes it easier to include flicker as a variable in studies regarding the impacts of lighting on organisms.
- Open Access
- 28 September 2023
- Published by MDPI AG in Remote Sensing
- Vol. 15 (19) , 4760
Global Satellite Monitoring of Exothermic Industrial Activity via Infrared Emissions
This paper reports on the first daily global monitoring program for natural gas flaring and industrial sites producing waste heat based on satellite observed infrared emissions. The Visible Infrared Imaging Radiometer Suite (VIIRS) collects nightly global infrared data in spectral bands ranging from near infrared (NIR) to longwave infrared (LWIR), providing a unique capability to detect and characterize infrared emitters at night. The VIIRS nightfire (VNF) algorithm identifies infrared (IR) emitters with multiple spectral bands and calculates the temperature, source area, and radiant heat via Planck curve fitting and physical laws. VNF data are produced nightly and extend from 2012 to the present. The most common infrared emitter is biomass burning, which must be filtered out. Industrial IR emitters can be distinguished from biomass burning based on temperature and persistence. The initial filtering to remove biomass burning was performed with 15 arc second grids formed from eleven years of VIIRS data, spanning 2012–2022. The locations and shapes of the remaining features were used to guide the generation of super-resolution pixel center clouds. These data clouds were then analyzed to define bounding vectors for single emitters and to split larger clusters into multiple emitters. A total of nearly 20,000 IR emitters were identified; each was assigned an identification number, and the type of emitter was recorded. Nightly temporal profiles were produced for each site, revealing activity patterns back to 2012. Nightly temporal profiles were kept current with weekly updates. Temporal profiles from individual sites were aggregated by country to form monthly profiles extending back to 2012. The nightly and monthly temporal profiles were suitable for analyzing industrial production, identifying disruption events, and tracking recovery. The data could also be used in tracking progress in energy conservation and greenhouse gas emission inventories.
- 28 September 2023
- Published by MDPI AG in Remote Sensing
- Vol. 15 (19) , 4760
Open AccessGlobal Satellite Monitoring of Exothermic Industrial Activity via Infrared Emissions
This paper reports on the first daily global monitoring program for natural gas flaring and industrial sites producing waste heat based on satellite observed infrared emissions. The Visible Infrared Imaging Radiometer Suite (VIIRS) collects nightly global infrared data in spectral bands ranging from near infrared (NIR) to longwave infrared (LWIR), providing a unique capability to detect and characterize infrared emitters at night. The VIIRS nightfire (VNF) algorithm identifies infrared (IR) emitters with multiple spectral bands and calculates the temperature, source area, and radiant heat via Planck curve fitting and physical laws. VNF data are produced nightly and extend from 2012 to the present. The most common infrared emitter is biomass burning, which must be filtered out. Industrial IR emitters can be distinguished from biomass burning based on temperature and persistence. The initial filtering to remove biomass burning was performed with 15 arc second grids formed from eleven years of VIIRS data, spanning 2012–2022. The locations and shapes of the remaining features were used to guide the generation of super-resolution pixel center clouds. These data clouds were then analyzed to define bounding vectors for single emitters and to split larger clusters into multiple emitters. A total of nearly 20,000 IR emitters were identified; each was assigned an identification number, and the type of emitter was recorded. Nightly temporal profiles were produced for each site, revealing activity patterns back to 2012. Nightly temporal profiles were kept current with weekly updates. Temporal profiles from individual sites were aggregated by country to form monthly profiles extending back to 2012. The nightly and monthly temporal profiles were suitable for analyzing industrial production, identifying disruption events, and tracking recovery. The data could also be used in tracking progress in energy conservation and greenhouse gas emission inventories.
- 28 April 2023
- Published by Springer Nature
- p. 1109-1161
Policy, Legal Processes and Precedents for Space Mining
- 28 April 2023
- Published by Springer Nature
- p. 1109-1161
Policy, Legal Processes and Precedents for Space Mining
- Top Cited PapersOpen Access
Pandemic, War, and Global Energy Transitions
The COVID-19 pandemic and Russia’s war on Ukraine have impacted the global economy, including the energy sector. The pandemic caused drastic fluctuations in energy demand, oil price shocks, disruptions in energy supply chains, and hampered energy investments, while the war left the world with energy price hikes and energy security challenges. The long-term impacts of these crises on low-carbon energy transitions and mitigation of climate change are still uncertain but are slowly emerging. This paper analyzes the impacts throughout the energy system, including upstream fuel supply, renewable energy investments, demand for energy services, and implications for energy equity, by reviewing recent studies and consulting experts in the field. We find that both crises initially appeared as opportunities for low-carbon energy transitions: the pandemic by showing the extent of lifestyle and behavioral change in a short period and the role of science-based policy advice, and the war by highlighting the need for greater energy diversification and reliance on local, renewable energy sources. However, the early evidence suggests that policymaking worldwide is focused on short-term, seemingly quicker solutions, such as supporting the incumbent energy industry in the post-pandemic era to save the economy and looking for new fossil fuel supply routes for enhancing energy security following the war. As such, the fossil fuel industry may emerge even stronger after these energy crises creating new lock-ins. This implies that the public sentiment against dependency on fossil fuels may end as a lost opportunity to translate into actions toward climate-friendly energy transitions, without ambitious plans for phasing out such fuels altogether. We propose policy recommendations to overcome these challenges toward achieving resilient and sustainable energy systems, mostly driven by energy services.
Top Cited PapersOpen AccessPandemic, War, and Global Energy Transitions
The COVID-19 pandemic and Russia’s war on Ukraine have impacted the global economy, including the energy sector. The pandemic caused drastic fluctuations in energy demand, oil price shocks, disruptions in energy supply chains, and hampered energy investments, while the war left the world with energy price hikes and energy security challenges. The long-term impacts of these crises on low-carbon energy transitions and mitigation of climate change are still uncertain but are slowly emerging. This paper analyzes the impacts throughout the energy system, including upstream fuel supply, renewable energy investments, demand for energy services, and implications for energy equity, by reviewing recent studies and consulting experts in the field. We find that both crises initially appeared as opportunities for low-carbon energy transitions: the pandemic by showing the extent of lifestyle and behavioral change in a short period and the role of science-based policy advice, and the war by highlighting the need for greater energy diversification and reliance on local, renewable energy sources. However, the early evidence suggests that policymaking worldwide is focused on short-term, seemingly quicker solutions, such as supporting the incumbent energy industry in the post-pandemic era to save the economy and looking for new fossil fuel supply routes for enhancing energy security following the war. As such, the fossil fuel industry may emerge even stronger after these energy crises creating new lock-ins. This implies that the public sentiment against dependency on fossil fuels may end as a lost opportunity to translate into actions toward climate-friendly energy transitions, without ambitious plans for phasing out such fuels altogether. We propose policy recommendations to overcome these challenges toward achieving resilient and sustainable energy systems, mostly driven by energy services.
- Open Access
- 9 March 2022
- Published by MDPI AG in Remote Sensing
- Vol. 14 (6) , 1316
The VIIRS Day/Night Band: A Flicker Meter in Space?
The VIIRS day/night band (DNB) high gain stage (HGS) pixel effective dwell time is in the range of 2–3 milliseconds (ms), which is about one third of the flicker cycle present in lighting powered by alternating current. Thus, if flicker is present, it induces random fluctuations in nightly DNB radiances. This results in increased variance in DNB temporal profiles. A survey of flicker characteristics conducted with high-speed camera data collected on a wide range of individual luminaires found that the flicker is most pronounced in high-intensity discharge (HID) lamps, such as high- and low-pressure sodium and metal halides. Flicker is muted, but detectable, in incandescent luminaires. Modern light-emitting diodes (LEDs) and fluorescent lights are often nearly flicker-free, thanks to high-quality voltage smoothing. DNB pixel footprints are about half a square kilometer and can contain vast numbers of individual luminaires, some of which flicker, while others do not. If many of the flickering lights are drawing from a common AC supplier, the flicker can be synchronized and leave an imprint on the DNB temporal profile. In contrast, multiple power supplies will throw the flickering out of synchronization, resulting in a cacophony with less radiance fluctuation. The examination of DNB temporal profiles for locations before and after the conversion of high-intensity discharge (HID) to LED streetlight conversions shows a reduction in the index of dispersion, calculated by dividing the annual variance by the mean. There are a number of variables that contribute to radiance variations in the VIIRS DNB, including the view angle, cloud optical thickness, atmospheric variability, snow cover, lunar illuminance, and the compilation of temporal profiles using pixels whose footprints are not perfectly aligned. It makes sense to adjust the DNB radiance for as many of these extraneous effects as possible. However, none of these adjustments will reduce the radiance instability introduced by flicker. Because flicker is known to affect organisms, including humans, the development of methods to detect and rate the strength of flickering from space will open up new areas of research on the biologic impacts of artificial lighting. Over time, there is a trend towards the reduction of flicker in outdoor lighting through the replacement of HID with low-flicker LED sources. This study indicates that the effects of LED conversions on the brightness and steadiness of outdoor lighting can be analyzed with VIIRS DNB temporal profiles.
- 9 March 2022
- Published by MDPI AG in Remote Sensing
- Vol. 14 (6) , 1316
Open AccessThe VIIRS Day/Night Band: A Flicker Meter in Space?
The VIIRS day/night band (DNB) high gain stage (HGS) pixel effective dwell time is in the range of 2–3 milliseconds (ms), which is about one third of the flicker cycle present in lighting powered by alternating current. Thus, if flicker is present, it induces random fluctuations in nightly DNB radiances. This results in increased variance in DNB temporal profiles. A survey of flicker characteristics conducted with high-speed camera data collected on a wide range of individual luminaires found that the flicker is most pronounced in high-intensity discharge (HID) lamps, such as high- and low-pressure sodium and metal halides. Flicker is muted, but detectable, in incandescent luminaires. Modern light-emitting diodes (LEDs) and fluorescent lights are often nearly flicker-free, thanks to high-quality voltage smoothing. DNB pixel footprints are about half a square kilometer and can contain vast numbers of individual luminaires, some of which flicker, while others do not. If many of the flickering lights are drawing from a common AC supplier, the flicker can be synchronized and leave an imprint on the DNB temporal profile. In contrast, multiple power supplies will throw the flickering out of synchronization, resulting in a cacophony with less radiance fluctuation. The examination of DNB temporal profiles for locations before and after the conversion of high-intensity discharge (HID) to LED streetlight conversions shows a reduction in the index of dispersion, calculated by dividing the annual variance by the mean. There are a number of variables that contribute to radiance variations in the VIIRS DNB, including the view angle, cloud optical thickness, atmospheric variability, snow cover, lunar illuminance, and the compilation of temporal profiles using pixels whose footprints are not perfectly aligned. It makes sense to adjust the DNB radiance for as many of these extraneous effects as possible. However, none of these adjustments will reduce the radiance instability introduced by flicker. Because flicker is known to affect organisms, including humans, the development of methods to detect and rate the strength of flickering from space will open up new areas of research on the biologic impacts of artificial lighting. Over time, there is a trend towards the reduction of flicker in outdoor lighting through the replacement of HID with low-flicker LED sources. This study indicates that the effects of LED conversions on the brightness and steadiness of outdoor lighting can be analyzed with VIIRS DNB temporal profiles.