Shinya Matsuda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shinya Matsuda has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
Keiji Ogi
Ehime Univ, Grad Sch Sci & Engn, 3 Bunkyocho, Matsuyama, Ehime 7908577, Japan
10 shared publicationsManabu Takahashi
Department of Industrial Innovation, Faculty of Collaborative Regional Innovation, Ehime University
9 shared publicationsNagatoshi Okabe
Graduate School of Sci. & Eng., Ehime Univ
6 shared publications- Masafumi Matsushita
Department of Mechanical Engineering, Ehime University
5 shared publications - Kazumasa Oshima
Dept. of Chemical Engineering, Faculty of Engineering, Kyushu University
4 shared publications Hiroaki Ohfuji
Geodynamics Res. Center, Ehime Univ
3 shared publications
Latest Publications
- 23 September 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (12) , 5725-5737
Very‐High‐Cycle Fatigue Behavior of Railway Axle Steel Subjected to Induction Hardening and Press Fitting
Rotary‐bending fatigue tests were carried out using induction‐hardened (IH) and press‐fitted (PF) specimens with a non‐IH axle component to evaluate the effects of induction hardening and press fitting on the fatigue behavior of railway axle steel up to the very‐high‐cycle fatigue (VHCF) regime. Induction hardening increased the fatigue limit by about 350 MPa. Fractures in the IH specimens were classified into three types based on their location and mode. These types were successfully explained using local fatigue strength, stress distributions, and microstructural observations. In contrast, press fitting reduced the fatigue limit by about 200 MPa due to stress concentration and fretting‐induced surface roughening.
- 23 September 2026
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 49 (12) , 5725-5737
Very‐High‐Cycle Fatigue Behavior of Railway Axle Steel Subjected to Induction Hardening and Press Fitting
Rotary‐bending fatigue tests were carried out using induction‐hardened (IH) and press‐fitted (PF) specimens with a non‐IH axle component to evaluate the effects of induction hardening and press fitting on the fatigue behavior of railway axle steel up to the very‐high‐cycle fatigue (VHCF) regime. Induction hardening increased the fatigue limit by about 350 MPa. Fractures in the IH specimens were classified into three types based on their location and mode. These types were successfully explained using local fatigue strength, stress distributions, and microstructural observations. In contrast, press fitting reduced the fatigue limit by about 200 MPa due to stress concentration and fretting‐induced surface roughening.
- 26 November 2024
- Published by Elsevier in Materials Letters
- Vol. 381
Effects of constituent materials on resin separation from CFRP by electrical treatment
- 26 November 2024
- Published by Elsevier in Materials Letters
- Vol. 381
Effects of constituent materials on resin separation from CFRP by electrical treatment
- 9 September 2022
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 32 (4) , 519-531
Voids formation characteristics in typical epoxy-based CFRP laminates during low-temperature annealing in the air or N2 atmosphere
The feedstock recycling of carbon fiber reinforced plastics (CFRPs) is typically conducted by either thermal decomposition or dissolution methods for resin separation. A common issue in the recycling processes is that neither oxygen nor solvents can easily penetrate dense CFRP; therefore, penetrating diffusion paths such as voids is expected to improve the separation efficiency. This study presents voids formation characteristics by low-temperature annealing as pre-treatment in typical epoxy-based cross-ply CFRP laminates. The void characteristics were evaluated by electrical treatment and observations after the annealing in the air or N2 atmosphere. Annealing in air resulted primarily in ply delamination and matrix cracking through slight oxidative reactions. By contrast, annealing in the N2 atmosphere denatured the epoxy resin, resulting in the formation of voids and swelling that reached the interior of the specimens. The void characteristics could be controlled by the atmosphere in the low-temperature annealing, leading to the penetrating diffusion paths.
- 9 September 2022
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 32 (4) , 519-531
Voids formation characteristics in typical epoxy-based CFRP laminates during low-temperature annealing in the air or N2 atmosphere
The feedstock recycling of carbon fiber reinforced plastics (CFRPs) is typically conducted by either thermal decomposition or dissolution methods for resin separation. A common issue in the recycling processes is that neither oxygen nor solvents can easily penetrate dense CFRP; therefore, penetrating diffusion paths such as voids is expected to improve the separation efficiency. This study presents voids formation characteristics by low-temperature annealing as pre-treatment in typical epoxy-based cross-ply CFRP laminates. The void characteristics were evaluated by electrical treatment and observations after the annealing in the air or N2 atmosphere. Annealing in air resulted primarily in ply delamination and matrix cracking through slight oxidative reactions. By contrast, annealing in the N2 atmosphere denatured the epoxy resin, resulting in the formation of voids and swelling that reached the interior of the specimens. The void characteristics could be controlled by the atmosphere in the low-temperature annealing, leading to the penetrating diffusion paths.
- 1 October 2021
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 255
Cyclic fatigue life characteristics of ceramic balls under variable thermal shock loadings
- 1 October 2021
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 255
Cyclic fatigue life characteristics of ceramic balls under variable thermal shock loadings
- 24 August 2021
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 55 (28) , 4111-4124
Characterization of piercing damage in CFRP cross-ply laminates after punch shear machining via impact loading
In industrial processes, piercing and trimming are essential because composite structures are usually manufactured in a near-net shape to reduce machining operations. Punching and shear cutting using out-of-plane shear loading are expected to increase productivity. Nevertheless, little is known about the effects of such operations on polymer-matrix composites. This study presents on the characterization of piercing damage in typical carbon fiber reinforced plastic (CFRP) cross-ply laminates [0°2/90°2]s after punching using quasi-static (QS) and drop-weight impact (DWI) loadings. During QS punching, the upper and lower ply interfaces delaminate due to the high shear stress to cut fibers and gradual shear deformation in the middle ply; however, during DWI punching at a low impact velocity, delamination of the lower ply interface can be reduced due to the localization of shear deformation, as compared to that in QS punching. Finally, the damage accumulation process during DWI punching is discussed.
- 24 August 2021
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 55 (28) , 4111-4124
Characterization of piercing damage in CFRP cross-ply laminates after punch shear machining via impact loading
In industrial processes, piercing and trimming are essential because composite structures are usually manufactured in a near-net shape to reduce machining operations. Punching and shear cutting using out-of-plane shear loading are expected to increase productivity. Nevertheless, little is known about the effects of such operations on polymer-matrix composites. This study presents on the characterization of piercing damage in typical carbon fiber reinforced plastic (CFRP) cross-ply laminates [0°2/90°2]s after punching using quasi-static (QS) and drop-weight impact (DWI) loadings. During QS punching, the upper and lower ply interfaces delaminate due to the high shear stress to cut fibers and gradual shear deformation in the middle ply; however, during DWI punching at a low impact velocity, delamination of the lower ply interface can be reduced due to the localization of shear deformation, as compared to that in QS punching. Finally, the damage accumulation process during DWI punching is discussed.
- 1 February 2020
- Published by Elsevier in Composite Structures
- Vol. 234
Effect of annealing on the separation of resin from CFRP cross-ply laminate via electrical treatment
- 1 February 2020
- Published by Elsevier in Composite Structures
- Vol. 234
Effect of annealing on the separation of resin from CFRP cross-ply laminate via electrical treatment