Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mieczysław Słowik has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Assessment of Low-Temperature Properties of Styrene–Butadiene–Styrene-Modified Asphalt Binders and Mastics Based on Relaxation Characteristics

    by Mieczysław Słowik, Marta Mielczarek

    This study investigates the low-temperature relaxation behavior of asphalt binders and asphalt mastics using a ductilometer-based uniaxial tensile relaxation test under a constant displacement rate. Although the low-temperature performance of SBS-modified asphalt binders has been widely studied, the relaxation mechanisms of asphalt mastics containing SBS-modified binders, particularly considering the effects of the SBS content and short-term aging, remain insufficiently understood. Polymer-modified binders were prepared from 50/70 penetration-grade bitumen blended with an industrially produced SBS copolymer concentrate containing 9% SBS. Three binders with SBS contents of 3%, 5%, and 7% were manufactured and used to prepare asphalt mastics with mineral filler. Tensile relaxation tests were performed at −12 °C on unaged and RTFOT-aged specimens. The relaxation behavior was evaluated using a modified generalized Maxwell model to describe the viscoelastic response of the materials. The novelty of this study lies in the systematic comparison of SBS-modified binders and corresponding asphalt mastics using a unified experimental and modeling approach. Unlike previous studies focused mainly on polymer-modified binders, this research extends the analysis to binder–filler systems and provides new insight into the influence of the SBS content and aging on stress relaxation mechanisms. The results demonstrate that increasing the SBS content improves the relaxation capacity of both the binders and mastics, enhancing their ability to dissipate thermally induced stresses. Moreover, a higher SBS content reduces the sensitivity of materials to short-term aging, indicating improved resistance to low-temperature cracking.

  • Open Access

    Glare Impact from Photovoltaic Systems on Driver Safety

    by Mieczysław Słowik, Przemysław Skrzypczak, Krzysztof Wandachowicz

    This article examines the potential risk of impaired visibility for drivers caused by sunlight reflecting off the surfaces of PV panels installed within the right-of-way of motorways and expressways. A literature review was conducted to describe the current state of knowledge and identify the requirements applicable to this area. The procedures for measuring the reflective properties of PV panels using a goniophotometer and a luminance camera (imaging luminance measuring device—ILMD) were evaluated. The measurement results for three PV panels with different surface structures are presented, allowing the properties of PV panels to be determined in terms of their potential impact on driver safety. A computer application was developed to determine whether the sun’s rays will reflect off a photovoltaic panel’s surface toward a vehicle’s direction of travel. The application graphically displays information on whether the sun will be reflected in the direction of a moving vehicle and whether this reflection poses a threat to driver safety. A comprehensive procedure for assessing the risk of glare caused by sunlight reflecting off the surfaces of photovoltaic panels was developed, along with detailed requirements. This study supports sustainable development by promoting renewable energy deployment in motorway corridors while simultaneously ensuring road safety. It integrates environmental (renewable energy use), social (driver safety), and technical (quantitative glare assessment methods) dimensions of sustainability.


  • Przegląd metod laboratoryjnych i mobilnych urządzeńpomiarowych stosowanych w diagnostyce nawierzchnieksploatowanych na sieciach drogowych

    by Przemysław Górnaś, Marta Mielczarek, Sylwia Fornalczyk, Andrzej Pożarycki, Mieczysław Słowik

    Artykuł przedstawia przegląd metod laboratoryjnychoraz mobilnych urządzeń pomiarowych wykorzystywanychw diagnostyce nawierzchni drogowych. Wprowadzanie w mieszankachmineralno-asfaltowych modyfikowanych lepiszczy asfaltowych,w tym wysokomodyfikowanych asfaltów (HiMA), znaczniepoprawia trwałość i elastyczność nawierzchni. Dodatkowo badaniareologiczne i mikroskopowe umożliwiają optymalizację składuasfaltu oraz prognozowanie jego zachowania w ekstremalnychwarunkach eksploatacji. Współczesne systemy zarządzania utrzymaniemsieci drogowej w Polsce pozwalają na skuteczne planowanieremontów i przebudów. Wykorzystanie zaawansowanychmetod diagnostycznych, takich jak mobilne urządzenia pomiarowei badania laboratoryjne pozwala na precyzyjną ocenę stanutechnicznego nawierzchni oraz dobór optymalnych technologiinaprawczych. Dzięki systemom diagnostycznym, takim jak ZiSPONzarządcy dróg mogą efektywnie monitorować stan techniczny nawierzchni,co sprzyja podejmowaniu racjonalnych decyzji inwestycyjnychi poprawie jakości infrastruktury drogowej

  • Open Access

    Evaluation of Rheological Properties of Polymer-Modified Asphalt Binders and Mastics with Organic Additive—Imidazoline

    by Marta Mielczarek, Sylwia Fornalczyk, Mieczysław Słowik

    The article presents the results of testing the asphalt binder modified with SBS copolymer (5%) and its mixture with mineral fillers called asphalt mastics. The aim of the research and analysis was to check the possibility of using an organic additive in the form of imidazolines and to assess their impact on the viscoelastic properties of the obtained asphalt mastics. The main advantage of using imidazoline is the increased resistance of asphalt mixtures to low-temperature cracking at the top of the road route and reducing its maintenance costs. Based on the examination of the adhesion of the binder with the addition of various imidazolines to the aggregate, a selection was made from six analyzed subtypes. One of them was selected for further research. The tests were carried out in a dynamic shear rheometer in a wide temperature range from −36 °C to 82 °C, determining the most important parameters of the tested materials, i.e., dynamic shear modulus (|G*|), phase angle (δ) and the non-recoverable creep compliance (Jnr). The test results and their analysis confirmed the beneficial effect of imidazoline on the viscoelastic properties of mastics in the low-temperature range, even at the lowest content of 0.2%. Based on the results of the determination of Jnr and |G*|/sinδ in the range of high operating temperatures, no significant deterioration in permanent deformation parameters was observed. Moreover, the use of imidazoline reduces technological temperatures during the production of HMA used in the pavement and, therefore, reduces CO2 emissions into the atmosphere.


  • Open Access

    Inicjacja warunków początkowych w modelu do analizy termicznej nawierzchni drogowej

    by Marcin Bilski, Przemysław Górnaś, Andrzej Pożarycki, Mieczysław Słowik, Paweł Mieczkowski

    W pracy rozpatrzono możliwość inicjacji warunków początkowych w modelu do analizy termicznej nawierzchni drogowej w warunkach niestacjonarnego przepływu ciepła. Procedura wymaga przeprowadzenia obliczeń dla odpowiednio długiego czasu inicjacji do uzyskania początkowego rozkładu temperatury, który jest podstawą dalszych analiz przepływu energii cieplnej. Główną część pracy stanowi prezentacja eksperymentu numerycznego przeprowadzonego dla czterech konfiguracji wartości parametrów modelu przepływu energii cieplnej w ośrodku wielowarstwowym, jakim jest nawierzchnia. Każda konfiguracja parametrów odpowiada innej konstrukcji (dwa modele nawierzchni podatnej i dwa modele z warstwą z pianobetonu). Obliczenia przeprowadzono kolejno dla trzech różnych wartości amplitud sinusoidalnej funkcji zmiany temperatury w czasie, którą zde- finiowano jako warunek brzegowy w modelu nawierzchni. Uzupełnieniem eksperymentu numerycznego były obliczenia przeprowadzone dla jednej wybranej konfiguracji wartości parametrów modelu, w którym warunek brzegowy stanowiły wartości temperatury zarejestrowane czujnikiem wbudowanym w nawierzchnię. Na podstawie analizy uzyskanych wyników potwierdzono, że inicjacja warunków początkowych w równaniu przewodzenia ciepła jest możliwa w oparciu o analizę niestacjonarnego przepływu ciepła przedstawioną metodą.

  • Open Access

    Development and Analysis of High-Modulus Asphalt Concrete Predictive Model

    by Mikołaj Bartkowiak, Mieczysław Słowik

    The main purpose of this paper is to present the development of a new predictive model intended for the calculation of stiffness modulus |E*| determined by a four-point bending beam test (4PBB or 4PB-PR). The model developed, called model A, was based on the Witczak model, which was developed for the dynamic-modulus (DM) method. Most of the asphalt mixtures used to develop the model were high-modulus asphalt concrete (HMAC). The most commonly used methods for determining the stiffness modulus |E*| of asphalt mixtures were also discussed. The paper presents the results of the study for 10 asphalt mixtures but 8 of them were used to develop the predictive model. In addition, the results of complex shear modulus G* tests on neat and modified bituminous binders carried out in a dynamic shear rheometer (DSR), necessary for the development of a predictive model, are presented. The tests carried out in the dynamic shear rheometer had significant measurement uncertainties. The results of the volumetric parameters of the asphalt mixtures are also reported. The developed model A has maximum absolute errors e = 1930 MPa (p = 95%) and maximum relative errors re = 50% (p = 95%). The distribution of the absolute errors of the model, after discarding outliers, has a normal distribution as in the development of other models of this type, which was confirmed by appropriate statistical tests. On the basis of the tests and calculations carried out, it was concluded that, in order to increase the precision of the predictive models, it is advisable to reduce the measurement uncertainty of the bitumen complex shear modulus G*. For the developed model A, the limiting values of the stiffness modulus |E*| are also shown, within which the determined stiffness modulus should fall.


  • Open Access

    Thermal Diffusivity of Concrete Samples Assessment Using a Solar Simulator

    by Marcin Bilski, Przemysław Górnaś, Andrzej Pożarycki, Przemysław Skrzypczak, Mieczysław Słowik, Marta Mielczarek, Agnieszka Wróblewska, Łukasz Semkło

    The thermal properties of pavement layers made of concrete with varying bulk densities are a particularly interesting topic in the context of development road technologies. If a hybrid layer system is used as a starting point, with thin asphalt layers (from 1 cm to 4 cm) laid on top of a foam concrete layer, thermal properties begin to play a crucial role. The main research problem was to create a test method enabling the assessment of the influence of solar heating on the thermal parameters of the building material, especially cement concrete. For this reason, this paper is concerned specifically with the assessment of a new methodology for testing and calculating the value of the thermal diffusivity coefficient of samples made of concrete varying bulk densities. In this case, using the proprietary concept the authors built a solar simulator using a multi-source lighting system. The analysis of the results of laboratory tests and numerical analyses allowed the authors to observe that there is a strong correlation between the bulk density of samples heated and the thermal diffusivity parameter, which appears in the unidirectional heat transfer equation. The strength of this relationship has been expressed with the coefficient of determination and amounts to 99%. The calculated values of the coefficient of thermal diffusivity for samples made of foam concrete range from 0.16×10−6m2s to 0.52×10−6m2s and are lower (from 2.5 to 8 times) than the value determined for samples made of typical cement concrete.


  • Open Access

    Ocena wpływu sposobu dozowania dodatku asfaltu naturalnego Gilsonite na właściwości mieszanki mineralno-asfaltowej

    by Marcin Bilski, Marta Mielczarek, Przemysław Górnaś, Mieczysław Słowik, Patrycja Wojciechowska

    W pracy przedstawiono wyniki badań laboratoryjnych mieszanek mineralno-asfaltowych (MMA) typu beton asfaltowy, które zawierały w swoim składzie dodatek asfaltu naturalnego Gilsonite w ilości 4% w stosunku wagowym do masy asfaltu, dozowany dwiema metodami: „na mokro" lub „na sucho”. Zakres przeprowadzonych badań laboratoryjnych obejmował oznaczenie modułów sztywności w badaniach pośredniego rozciągania, modułów sztywności metodą pełzania pod obciążeniem statycznym oraz odporności na działanie wody i mrozu. Na podstawie analizy statystycznej otrzymanych wyników badań laboratoryjnych dokonano oceny istotności różnic w uzyskanych właściwościach MMA zawierających dodatek Gilsonite dozowany różnymi metodami, w porównaniu do wartości uzyskanych na mieszance referencyjnej. Ustalono, że metoda dozowania („na mokro" lub „na sucho") dodatku asfaltu naturalnego Gilsonite do analizowanej mieszanki mineralno-asfaltowej typu beton asfaltowy nie ma istotnego wpływu na wartości modułów sztywności oznaczonych metodą IT-CY, metodą pełzania, a także na wartości wskaźnika wytrzymałości na rozciąganie pośrednie ITSR.


  • Open Access

    Study on Styrene-Butadiene-Styrene Modified Asphalt Binders Relaxation at Low Temperature

    by Sylwia Dziadosz, Mieczysław Słowik, Filip Niwczyk, Marcin Bilski

    The paper presents the results of laboratory investigation on asphalt binders relaxation at low temperature, carried out in a ductilometer using the tensile test with continuous force measurement. Polymer modified asphalt binder samples consisting of a 50/70 penetration grade bitumen mixed with a concentrate of styrene-butadiene-styrene (SBS) modified bitumen—a 160/220 penetration grade bitumen modified with a SBS copolymer in the amount of 9%—were tested. Therefore, polymer modified binders containing 3%, 4.5%, 6% and 7.5% SBS, respectively, were obtained and investigated. Tensile tests were performed at −16 °C on samples before aging and subjected to short-term aging (RTFOT). Test results in the form of relaxation curves have been mathematically described using a modified generalized Maxwell model. Based on the acquired results, it was shown that the increase of the SBS copolymer content in asphalt binder precipitates the relaxation process, while aging slows down this phenomenon. It has also been proven that with increased content of SBS elastomer in asphalt binder, the effect of short-term aging on binder’s stress relaxation ability at low temperatures is reduced.


  • Open Access

    Experimental Study of Tensile Properties of Styrene–Butadiene–Styrene Modified Asphalt Binders

    by Paweł Mieczkowski, Bartosz Budziński, Mieczysław Słowik, Jan Kempa, Wojciech Sorociak

    The requirements imposed on road pavements are ever increasing nowadays, necessitating the improvement of the properties of paving materials. The most commonly used paving materials include bituminous mixtures that are composed of aggregate grains bound by a bituminous binder. The properties of bitumens can be improved by modification with polymers. Among the copolymers used for modifying bitumens, styrene–butadiene–styrene, a thermoplastic elastomer, is the most commonly used. This article presents the results of tests conducted on bitumens modified with two types of styrene–butadiene–styrene copolymer (linear and radial). Two bitumen types of different penetration grades (35/50 and 160/220) were used in the experiments. The content of styrene–butadiene–styrene added to the bitumen varied between 1% and 6%. The results of the force ductility test showed that cohesion energy can be used for qualitative evaluation of the efficiency of modification of bitumen with styrene–butadiene–styrene copolymer. The determined values of the cohesion energy were subjected to the original analysis taking into account the three characteristic elongation zones of the tested binders. The performed analyses made it possible to find a parameter whose values correlate significantly with the content of styrene–butadiene–styrene copolymer in the modified bitumen. With smaller amounts of added modifier (approximately 2%), slightly better effects were obtained in the case of linear copolymer styrene–butadiene–styrene and for larger amounts of modifier (5–6%) radial copolymer styrene–butadiene–styrene was found to be more effective. This is confirmed by the changes in the binder structure, as indicated by the penetration index (PI).