Joachim Rohn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Joachim Rohn has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Sebastian Baumgärtel
GeoZentrum Nordbayern, Department Geographie und Geowissenschaften, Friedrich-Alexander-University Erlangen-Nuremberg, Schlossgarten 5, 91054 Erlangen, Germany
3 shared publications - Wei Xiang
Faculty of Engineering, China University of Geosciences (Wuhan), Wuhan 430074, China
3 shared publications - Jin Luo
Faculty of Engineering, China University of Geosciences (Wuhan), Wuhan 430074, China
2 shared publications - Julian A. V. Schweighofer
GeoZentrum Nordbayern, Department Geographie und Geowissenschaften, Friedrich-Alexander-University Erlangen-Nuremberg, Schlossgarten 5, 91054 Erlangen, Germany
2 shared publications - Zhenhua Wang
GeoZentrum Nordbayern, Department Geographie und Geowissenschaften, Friedrich-Alexander University Erlangen-Nuremberg (FAU), 91054 Erlangen, Germany
2 shared publications - Jens Winkler
GeoZentrum Nordbayern, Department Geographie und Geowissenschaften, Friedrich-Alexander University Erlangen-Nuremberg (FAU), 91054 Erlangen, Germany
1 shared publication
Latest Publications
- Open Access
Brazilian Tensile Strength of High-Water Content Clayey Soils Stabilized with Cement and Super-Absorbent Polymers
The tensile strength of stabilized clayey soil is a key indicator of its resistance to cracking and directly governs its performance when used as subgrade fill. In this study, ordinary Portland cement and polyacrylate-based super-absorbent polymers (SAP) were combined to stabilize four typical high-water content clayey soils sourced from Northern Bavaria. The optimal SAP content was determined based on absorption capacity by the tea-bag method. Subsequently, the effects of cement content and curing period on the Brazilian tensile strength (BTS) of clayey soils were investigated, and the correlation between Brazilian tensile strength and unconfined compressive strength (UCS) was discussed. The results indicated the following: the optimal SAP content was 0.3%; the BTS increased significantly with higher cement content and a longer curing period; the failure modes of BTS specimens were revealed, including multiple non-through fracture, non-central fracture, and central fracture; a strong linear correlation was established between BTS and UCS, with the proportional coefficient ranging from 0.129 to 0.233. The findings of this study can provide a valuable reference for the design and application of cement-SAP stabilized soils in practical engineering.
Open AccessBrazilian Tensile Strength of High-Water Content Clayey Soils Stabilized with Cement and Super-Absorbent Polymers
The tensile strength of stabilized clayey soil is a key indicator of its resistance to cracking and directly governs its performance when used as subgrade fill. In this study, ordinary Portland cement and polyacrylate-based super-absorbent polymers (SAP) were combined to stabilize four typical high-water content clayey soils sourced from Northern Bavaria. The optimal SAP content was determined based on absorption capacity by the tea-bag method. Subsequently, the effects of cement content and curing period on the Brazilian tensile strength (BTS) of clayey soils were investigated, and the correlation between Brazilian tensile strength and unconfined compressive strength (UCS) was discussed. The results indicated the following: the optimal SAP content was 0.3%; the BTS increased significantly with higher cement content and a longer curing period; the failure modes of BTS specimens were revealed, including multiple non-through fracture, non-central fracture, and central fracture; a strong linear correlation was established between BTS and UCS, with the proportional coefficient ranging from 0.129 to 0.233. The findings of this study can provide a valuable reference for the design and application of cement-SAP stabilized soils in practical engineering.
- Open Access
- 15 May 2023
- Published by Copernicus GmbH
Strength performance of high-water content clays stabilized with cement and superabsorbent polymers
An ideal solution for dealing with large volumes of waste clays is to stabilize and use them as fill materials for road construction. This paper presents an experimental study on the strength behavior of the clays with high water content stabilized by cement and superabsorbent polymers (SAP) at different curing periods. The SAP can effectively improve the strength of cement soils, and the increase in strength becomes more significant with time. The microstructures of the stabilized soils are also investigated via mercury intrusion porosimetry (MIP) and microcomputed tomography (Miro-CT). Comparison of the porosity and the pore size distribution of the stabilized soils shows clearly that the SAP facilitated the hydration/pozzolanic reaction through the absorption-release on free water. With this concept, free water, cement content, and curing period are considered as important parameters based on Abrams' law to characterize the strength of the cement-SAP-soil system.
- 15 May 2023
- Published by Copernicus GmbH
Open AccessStrength performance of high-water content clays stabilized with cement and superabsorbent polymers
An ideal solution for dealing with large volumes of waste clays is to stabilize and use them as fill materials for road construction. This paper presents an experimental study on the strength behavior of the clays with high water content stabilized by cement and superabsorbent polymers (SAP) at different curing periods. The SAP can effectively improve the strength of cement soils, and the increase in strength becomes more significant with time. The microstructures of the stabilized soils are also investigated via mercury intrusion porosimetry (MIP) and microcomputed tomography (Miro-CT). Comparison of the porosity and the pore size distribution of the stabilized soils shows clearly that the SAP facilitated the hydration/pozzolanic reaction through the absorption-release on free water. With this concept, free water, cement content, and curing period are considered as important parameters based on Abrams' law to characterize the strength of the cement-SAP-soil system.
- Open Access
Detecting Groundwater Temperature Shifts of a Subsurface Urban Heat Island in SE Germany
The subsurface beneath cities commonly shows a temperature anomaly, a so-called Subsurface Urban Heat Island (SUHI), due to anthropogenic heat input. This excess heat has multiple effects on groundwater and energy resources, such as groundwater chemistry or the efficiency of geothermal systems, which makes it necessary to investigate the temporal development of a SUHI. For this purpose, temperature profiles of 38 observation wells in the German city of Nuremberg were evaluated from 2015 to 2020 and the measured temperature changes were linked to the surface sealing. The results show that the groundwater temperatures changed between −0.02 K/a and +0.21 K/a, on average by +0.07 K/a during this period. A dependence between the temperature increase and the degree of sealing of the land surface was also observed. In areas with low surface sealing of up to 30% the warming amounts were 0.03 K/a on average, whereas in areas with high sealing of over 60% significantly higher temperature increases of 0.08 K/a on average were found. The results clearly emphasize that the subsurface urban heat island in its current state does not represent a completed process, but that more heat energy continues to enter the subsoil within the city than is the case with near-natural land surfaces.
Open AccessDetecting Groundwater Temperature Shifts of a Subsurface Urban Heat Island in SE Germany
The subsurface beneath cities commonly shows a temperature anomaly, a so-called Subsurface Urban Heat Island (SUHI), due to anthropogenic heat input. This excess heat has multiple effects on groundwater and energy resources, such as groundwater chemistry or the efficiency of geothermal systems, which makes it necessary to investigate the temporal development of a SUHI. For this purpose, temperature profiles of 38 observation wells in the German city of Nuremberg were evaluated from 2015 to 2020 and the measured temperature changes were linked to the surface sealing. The results show that the groundwater temperatures changed between −0.02 K/a and +0.21 K/a, on average by +0.07 K/a during this period. A dependence between the temperature increase and the degree of sealing of the land surface was also observed. In areas with low surface sealing of up to 30% the warming amounts were 0.03 K/a on average, whereas in areas with high sealing of over 60% significantly higher temperature increases of 0.08 K/a on average were found. The results clearly emphasize that the subsurface urban heat island in its current state does not represent a completed process, but that more heat energy continues to enter the subsoil within the city than is the case with near-natural land surfaces.
- Open Access
- 5 January 2021
- Published by MDPI AG in Geosciences
- Vol. 11 (1) , 24
Calculating Energy and Its Spatial Distribution for a Subsurface Urban Heat Island Using a GIS-Approach
In urban areas, the human influence on the city-ecosystem often results in a Subsurface Urban Heat Island (SUHI), which can be used geothermally. Unfortunately, a model of a SUHI does not consider the geology and hydrogeology of the subsoil. These can vary significantly over short distances, and are of considerable importance for the energy balance. In this work, we calculated the energy and its density stored in the subsoil via a SUHI. For this so-called energy-SUHI (e-SUHI), we evaluated the geology and its physical parameters for the first 20 m below ground level in the German city of Nuremberg and linked them to measured underground temperatures in a GIS application. This approach revealed stored energy of 1.634 × 1010 MJ within the soil and water for the study area with an area of 163 km2 and a volume of 3.26 × 109 m3. It corresponds to an average energy density of 5.0 MJ/m3. The highest energy density of 16.5 MJ/m3 was found in the city center area and correlated well to increases in subsurface temperature. As expected, our model reacts sensitively to thickness changes in the geological layers and the unsaturated zone.
- 5 January 2021
- Published by MDPI AG in Geosciences
- Vol. 11 (1) , 24
Open AccessCalculating Energy and Its Spatial Distribution for a Subsurface Urban Heat Island Using a GIS-Approach
In urban areas, the human influence on the city-ecosystem often results in a Subsurface Urban Heat Island (SUHI), which can be used geothermally. Unfortunately, a model of a SUHI does not consider the geology and hydrogeology of the subsoil. These can vary significantly over short distances, and are of considerable importance for the energy balance. In this work, we calculated the energy and its density stored in the subsoil via a SUHI. For this so-called energy-SUHI (e-SUHI), we evaluated the geology and its physical parameters for the first 20 m below ground level in the German city of Nuremberg and linked them to measured underground temperatures in a GIS application. This approach revealed stored energy of 1.634 × 1010 MJ within the soil and water for the study area with an area of 163 km2 and a volume of 3.26 × 109 m3. It corresponds to an average energy density of 5.0 MJ/m3. The highest energy density of 16.5 MJ/m3 was found in the city center area and correlated well to increases in subsurface temperature. As expected, our model reacts sensitively to thickness changes in the geological layers and the unsaturated zone.
- Open Access
A Novel Approach to the Analysis of Thermal Response Test (TRT) with Interrupted Power Input
The quality of measuring datasets of the thermal response test (TRT) significantly influences the interpretation of borehole thermal parameters (BTP). A thermal response test with an unstable power input may induce an unacceptable error in the estimation of the borehole thermal parameters. This paper proposes a novel approach to treat the dataset with interrupted power input. In this approach, the test records were segmented into several subsections with a constant time interval of 100 min, 60 min, and 30 min, separately. The quality of each data section was assessed and analyzed. Then, two algorithms, including the continuous algorithm and semi-superposition algorithm, were developed. The results estimated by the linear source model (LSM) were compared with one Thermal response test datasets with a stable power input at the same testing site. It shows that the effects of power interruption during the test can be effectively mitigated by deploying both the continuous and semi-superposition methods. The lowest deviation of the calculated thermal conductivity to a thermal response test with stable power input was 2.8% in the continuous method and 0.9% using the semi-superposition method. Thus, the proposed approaches are effective measures to mitigate the effects of interrupted power input on the interpretation of the thermal properties of the ground.
Open AccessA Novel Approach to the Analysis of Thermal Response Test (TRT) with Interrupted Power Input
The quality of measuring datasets of the thermal response test (TRT) significantly influences the interpretation of borehole thermal parameters (BTP). A thermal response test with an unstable power input may induce an unacceptable error in the estimation of the borehole thermal parameters. This paper proposes a novel approach to treat the dataset with interrupted power input. In this approach, the test records were segmented into several subsections with a constant time interval of 100 min, 60 min, and 30 min, separately. The quality of each data section was assessed and analyzed. Then, two algorithms, including the continuous algorithm and semi-superposition algorithm, were developed. The results estimated by the linear source model (LSM) were compared with one Thermal response test datasets with a stable power input at the same testing site. It shows that the effects of power interruption during the test can be effectively mitigated by deploying both the continuous and semi-superposition methods. The lowest deviation of the calculated thermal conductivity to a thermal response test with stable power input was 2.8% in the continuous method and 0.9% using the semi-superposition method. Thus, the proposed approaches are effective measures to mitigate the effects of interrupted power input on the interpretation of the thermal properties of the ground.
- Open Access
Investigation of Flow and Heat Transfer Characteristics in Fractured Granite
Hydraulic and heat transfer properties of artificially fractured rocks are the key issues for efficient exploitation of geothermal energy in fractured reservoirs and it has been studied by many previous researchers. However, the fluid temperature evolution along the flow path and rock temperature changes was rarely considered. This study investigated flow and heat transfer characteristics of two sets of fractured granite samples each with a single fissure. The samples were collected from a geothermal reservoir of Gonghe basin in Qinghai province in China. The results show that the larger area ratio, the higher hydraulic conductivity exhibited. Hydraulic conductivity of fractured rock masses is positively proportional to injection pressure, but inversely proportional with both confining pressure and temperature. In order to analyze heat transfer during the flow process, temperature distribution along the flow path in a fracture was monitored. The temperature of the fluid was determined to increase with distance from the flowing inlet. Increasing the temperature of the rock or decreasing the injection pressure will raise the temperature at the same location. Furthermore, in order to understand the heat transfer in rock mass, temperature distribution was observed by using an infrared thermal camera. Finally, the energy exchange efficiency during the flowing process was examined. The energy exchange rate increases continuously with the rock temperature, with an effective stress ratio of 1:2.
Open AccessInvestigation of Flow and Heat Transfer Characteristics in Fractured Granite
Hydraulic and heat transfer properties of artificially fractured rocks are the key issues for efficient exploitation of geothermal energy in fractured reservoirs and it has been studied by many previous researchers. However, the fluid temperature evolution along the flow path and rock temperature changes was rarely considered. This study investigated flow and heat transfer characteristics of two sets of fractured granite samples each with a single fissure. The samples were collected from a geothermal reservoir of Gonghe basin in Qinghai province in China. The results show that the larger area ratio, the higher hydraulic conductivity exhibited. Hydraulic conductivity of fractured rock masses is positively proportional to injection pressure, but inversely proportional with both confining pressure and temperature. In order to analyze heat transfer during the flow process, temperature distribution along the flow path in a fracture was monitored. The temperature of the fluid was determined to increase with distance from the flowing inlet. Increasing the temperature of the rock or decreasing the injection pressure will raise the temperature at the same location. Furthermore, in order to understand the heat transfer in rock mass, temperature distribution was observed by using an infrared thermal camera. Finally, the energy exchange efficiency during the flowing process was examined. The energy exchange rate increases continuously with the rock temperature, with an effective stress ratio of 1:2.