Hua Deng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hua Deng has a total of 74 co-authors. Here are the top co-authors by number of shared publications:
- Hong He
Chinese Academy of Sciences
13 shared publications Tingting Pan
8 shared publications- Changbin Zhang
Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences
6 shared publications Jianguo Ding
Institute of Urban Environment, Chinese Academy of Sciences
6 shared publicationsYuqin Lu
Center for Excellence in Regional Atmospheric Environment, Key Laboratory of Urban Pollutant Conversion, Xiamen Key Laboratory of Indoor Air and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021, China
6 shared publications- Jinzhu Ma
State Key Joint Laboratory of Environment Simulation and Pollution Control, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085, China
5 shared publications
Latest Publications
- 1 October 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (40) , 21643-21651
Role of Frustrated Lewis Pairs in α-MnO2 for Low-Temperature Toluene Oxidation with Ozone
The catalytic performance of α-MnO2 in the ozonation of volatile organic compounds (VOCs) is highly synthesis-dependent, which determines surface defects, redox properties, and active site distribution. To investigate this, we prepared three α-MnO2 catalysts through precipitation (MnO2–P), hydrothermal synthesis (MnO2–H), and the crystal transformation approach (MnO2–C). The superior performance of MnO2–C is attributed to its abundant oxygen vacancies and favorable Mn3+/Mn4+ ratio, whereas the efficiency of MnO2–P and MnO2–H is limited by their coordination-saturated Mn sites and insufficient oxygen vacancies, leading to poor O3 activation. In contrast, the crystal transformation approach induces structural defects in MnO2–C, creating abundant oxygen vacancy clusters and an optimized Mn3+/Mn4+ ratio. This unique configuration forms frustrated Lewis pairs (FLPs) between Mn cations (LA) and oxygen anions (LB), synergistically activating O3 to generate reactive oxygen species. As a result, MnO2–C achieves 100% toluene conversion with 85% CO2 selectivity at 30 °C, far surpassing MnO2–P and MnO2–H. This work demonstrates that defect engineering via crystal transformation is an effective strategy for designing highly active catalysts for VOC removal.
- 1 October 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (40) , 21643-21651
Role of Frustrated Lewis Pairs in α-MnO2 for Low-Temperature Toluene Oxidation with Ozone
The catalytic performance of α-MnO2 in the ozonation of volatile organic compounds (VOCs) is highly synthesis-dependent, which determines surface defects, redox properties, and active site distribution. To investigate this, we prepared three α-MnO2 catalysts through precipitation (MnO2–P), hydrothermal synthesis (MnO2–H), and the crystal transformation approach (MnO2–C). The superior performance of MnO2–C is attributed to its abundant oxygen vacancies and favorable Mn3+/Mn4+ ratio, whereas the efficiency of MnO2–P and MnO2–H is limited by their coordination-saturated Mn sites and insufficient oxygen vacancies, leading to poor O3 activation. In contrast, the crystal transformation approach induces structural defects in MnO2–C, creating abundant oxygen vacancy clusters and an optimized Mn3+/Mn4+ ratio. This unique configuration forms frustrated Lewis pairs (FLPs) between Mn cations (LA) and oxygen anions (LB), synergistically activating O3 to generate reactive oxygen species. As a result, MnO2–C achieves 100% toluene conversion with 85% CO2 selectivity at 30 °C, far surpassing MnO2–P and MnO2–H. This work demonstrates that defect engineering via crystal transformation is an effective strategy for designing highly active catalysts for VOC removal.
- Open Access
- 31 July 2026
- Published by Elsevier in SSRN Electronic Journal
Linking Microscopic Structural Units to Macroscopic Performance: MnO6 Connectivity as a Structural Regulator of Oxygen Dynamics in VOC Oxidation
Although manganese-based oxides (MnOx) are promising catalysts for the combustion of volatile organic compounds (VOCs), a fundamental understanding of the intricate relationship between their atomic-scale structure and catalytic activity remains elusive. In this work, a series of Mn-based oxides with distinct local coordination environments (MnO2, Mn2O3, LaMnO3, and Mn3O4) were synthesized to examine the structure–oxygen dynamics–activity relationship in VOC oxidation via a Mars–van Krevelen (MvK) pathway. Across the series, VOC oxidation performance was more consistently associated with oxygen-release and redox behavior than with static surface descriptors considered individually. MnO2 combined a more heterogeneous and less uniformly constrained Mn–O network with a larger accessible oxygen reservoir and a more favorable low-temperature reduction response., which favors lattice-oxygen accessibility, oxygen transport, and oxygen-vacancy regeneration during redox cycling. In contrast, Mn2O3, LaMnO3, and Mn3O4 possess more constrained Mn–O frameworks, resulting in less favorable oxygen transport and vacancy replenishment kinetics, which leads to diminished redox flexibility and inferior performance. These results identify [MnO6] connectivity as a structural basis for the lattice-oxygen supply, vacancy regeneration, and catalyst reoxidation steps central to MvK oxidation. In-situ DRIFTS further revealed that MnO2 accelerated the formation and consumption of enolic intermediates during acetone oxidation, minimizing intermediate accumulation and enabling deep oxidation. Overall, the combined results support a connectivity-centered interpretation of the MvK process, in which [MnO6] connectivity provides an upstream structural context for oxygen delivery and redox cycling, while oxygen dynamics constitutes the more immediate mechanistic link to VOC oxidation performance.
- 31 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessLinking Microscopic Structural Units to Macroscopic Performance: MnO6 Connectivity as a Structural Regulator of Oxygen Dynamics in VOC Oxidation
Although manganese-based oxides (MnOx) are promising catalysts for the combustion of volatile organic compounds (VOCs), a fundamental understanding of the intricate relationship between their atomic-scale structure and catalytic activity remains elusive. In this work, a series of Mn-based oxides with distinct local coordination environments (MnO2, Mn2O3, LaMnO3, and Mn3O4) were synthesized to examine the structure–oxygen dynamics–activity relationship in VOC oxidation via a Mars–van Krevelen (MvK) pathway. Across the series, VOC oxidation performance was more consistently associated with oxygen-release and redox behavior than with static surface descriptors considered individually. MnO2 combined a more heterogeneous and less uniformly constrained Mn–O network with a larger accessible oxygen reservoir and a more favorable low-temperature reduction response., which favors lattice-oxygen accessibility, oxygen transport, and oxygen-vacancy regeneration during redox cycling. In contrast, Mn2O3, LaMnO3, and Mn3O4 possess more constrained Mn–O frameworks, resulting in less favorable oxygen transport and vacancy replenishment kinetics, which leads to diminished redox flexibility and inferior performance. These results identify [MnO6] connectivity as a structural basis for the lattice-oxygen supply, vacancy regeneration, and catalyst reoxidation steps central to MvK oxidation. In-situ DRIFTS further revealed that MnO2 accelerated the formation and consumption of enolic intermediates during acetone oxidation, minimizing intermediate accumulation and enabling deep oxidation. Overall, the combined results support a connectivity-centered interpretation of the MvK process, in which [MnO6] connectivity provides an upstream structural context for oxygen delivery and redox cycling, while oxygen dynamics constitutes the more immediate mechanistic link to VOC oxidation performance.
- 7 July 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (36) , 38856-38863
A Topotactic Leap: 2D Layers to 3D Large-Pore Zeolite
Zeolites with stable, three-dimensionally interconnected large-pore channels, such as the industrially pivotal Y zeolite, are indispensable for the catalytic and separation processing of bulky molecules. Nevertheless, the synthesis of new frameworks beyond established types remains a persistent challenge. Here, we show that 2D-to-3D topotactic condensation, previously known to produce predominantly 1D/2D-channel or small/medium-pore 3D structures, affords a novel 3D large-pore high-silica zeolite. Through structure-guided design, a cyclohexyl-enriched organic structure-directing agent was developed to stabilize terminal bea building units, leading to a new 2D large-pore, high-silica precursor, JU-67. Calcination of JU-67 induced its topotactic conversion into a 3D large-pore zeolite, JU-68. This material possesses a unique anisotropic 12 × 12 × 12-ring channel system and a large supercage, which confers unique xylene adsorption and promising performance in the catalytic cracking of heavy oil, achieving a propylene yield higher than that of the industrial USY-based catalyst.
- 7 July 2026
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 148 (36) , 38856-38863
A Topotactic Leap: 2D Layers to 3D Large-Pore Zeolite
Zeolites with stable, three-dimensionally interconnected large-pore channels, such as the industrially pivotal Y zeolite, are indispensable for the catalytic and separation processing of bulky molecules. Nevertheless, the synthesis of new frameworks beyond established types remains a persistent challenge. Here, we show that 2D-to-3D topotactic condensation, previously known to produce predominantly 1D/2D-channel or small/medium-pore 3D structures, affords a novel 3D large-pore high-silica zeolite. Through structure-guided design, a cyclohexyl-enriched organic structure-directing agent was developed to stabilize terminal bea building units, leading to a new 2D large-pore, high-silica precursor, JU-67. Calcination of JU-67 induced its topotactic conversion into a 3D large-pore zeolite, JU-68. This material possesses a unique anisotropic 12 × 12 × 12-ring channel system and a large supercage, which confers unique xylene adsorption and promising performance in the catalytic cracking of heavy oil, achieving a propylene yield higher than that of the industrial USY-based catalyst.
- Open Access
- 31 October 2025
- Published by Royal Society of Chemistry (RSC) in Chemical Science
- Vol. 16 (48) , 23262-23270
Single site of water-resistant asymmetric Bi–Ov–Mn for robust VOC ozonation at ambient temperature
Tailoring asymmetric Bi–Ov–Mn sites in α-MnO 2 through crystal transformation for superior VOC catalytic ozonation in humid environments.
- 31 October 2025
- Published by Royal Society of Chemistry (RSC) in Chemical Science
- Vol. 16 (48) , 23262-23270
Open AccessSingle site of water-resistant asymmetric Bi–Ov–Mn for robust VOC ozonation at ambient temperature
Tailoring asymmetric Bi–Ov–Mn sites in α-MnO 2 through crystal transformation for superior VOC catalytic ozonation in humid environments.
- 5 May 2025
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 59 (23) , 11875-11884
Tuning Pt-TiO2 Interactions to Switch Inhibition to Synergy in Toluene–Acetone Mixture Combustion
The inhibitory interactions among various volatile organic compounds (VOCs) during combustion in industrial exhaust gases pose a significant challenge for catalytic technologies, primarily due to a lack of effective approaches to counter these adverse effects. The interaction between Pt and TiO2 was readily tuned through hydrogen reduction of the TiO2 matrix (Pt/TiO2-800), which ultimately transformed the inhibitory effect into a synergistic effect in a toluene-acetone mixture. Optimal catalytic activity was achieved at 0.6 wt % Pt loading, with 0.6Pt/TiO2-800 lowering reaction temperatures by 21 °C for toluene and 24 °C for acetone in mixed VOC oxidation. Characterization reveals that Pt/TiO2-800 possesses abundant oxygen vacancy clusters, enhancing TiO2-Pt electron transfer, diversifying Pt nanoparticle sizes, stabilizing low-valent Pt species, and improving oxidative capacity. DFT calculations further underscore the role of oxygen vacancy in modulating the Pt electronic environment and enhancing defect-enhanced adsorption. This work advances Pt-TiO2 interaction understanding and offers an effective catalyst for VOCs abatement, addressing inhibitory effects in mixed VOCs systems.
- 5 May 2025
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 59 (23) , 11875-11884
Tuning Pt-TiO2 Interactions to Switch Inhibition to Synergy in Toluene–Acetone Mixture Combustion
The inhibitory interactions among various volatile organic compounds (VOCs) during combustion in industrial exhaust gases pose a significant challenge for catalytic technologies, primarily due to a lack of effective approaches to counter these adverse effects. The interaction between Pt and TiO2 was readily tuned through hydrogen reduction of the TiO2 matrix (Pt/TiO2-800), which ultimately transformed the inhibitory effect into a synergistic effect in a toluene-acetone mixture. Optimal catalytic activity was achieved at 0.6 wt % Pt loading, with 0.6Pt/TiO2-800 lowering reaction temperatures by 21 °C for toluene and 24 °C for acetone in mixed VOC oxidation. Characterization reveals that Pt/TiO2-800 possesses abundant oxygen vacancy clusters, enhancing TiO2-Pt electron transfer, diversifying Pt nanoparticle sizes, stabilizing low-valent Pt species, and improving oxidative capacity. DFT calculations further underscore the role of oxygen vacancy in modulating the Pt electronic environment and enhancing defect-enhanced adsorption. This work advances Pt-TiO2 interaction understanding and offers an effective catalyst for VOCs abatement, addressing inhibitory effects in mixed VOCs systems.
- 23 August 2024
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 678 (Pt A) , 520-531
Strong interaction between promoter and metal in Pd-Ba/TiO2 catalysts for formaldehyde oxidation
- 23 August 2024
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 678 (Pt A) , 520-531
Strong interaction between promoter and metal in Pd-Ba/TiO2 catalysts for formaldehyde oxidation
- 15 May 2024
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 58 (21) , 9381-9392
In-Depth Understanding of the Oxidative Compatibility of Volatile Organic Compounds with Mn2O3 and Pt-Loaded Catalysts
Designing suitable catalysts for efficiently degrading volatile organic compounds (VOCs) is a great challenge due to the distinct variety and nature of VOCs. Herein, the suitability of different typical VOCs (toluene and acetone) over Pt-based catalysts and Mn2O3 was investigated carefully. The activity of Mn2O3 was inferior to Pt-loaded catalysts in toluene oxidation but showed superior ability for destroying acetone, while Pt loading could boost the catalytic activity of Mn2O3 for both acetone and toluene. This suitability could be determined by the physicochemical properties of the catalysts and the structure of the VOC since toluene destruction activity is highly reliant on Pt0 in the metallic state and linearly correlated with the amount of surface reactive oxygen species (Oads), while the crucial factor that affects acetone oxidation is the mobility of lattice oxygen (Olat). The Pt/Mn2O3 catalyst shows highly active Pt-O-Mn interfacial sites, favoring the generation of Oads and promoting Mn-Olat mobility, leading to its excellent performance. Therefore, the design of abundant active sites is an effective means of developing highly adaptive catalysts for the oxidation of different VOCs.
- 15 May 2024
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 58 (21) , 9381-9392
In-Depth Understanding of the Oxidative Compatibility of Volatile Organic Compounds with Mn2O3 and Pt-Loaded Catalysts
Designing suitable catalysts for efficiently degrading volatile organic compounds (VOCs) is a great challenge due to the distinct variety and nature of VOCs. Herein, the suitability of different typical VOCs (toluene and acetone) over Pt-based catalysts and Mn2O3 was investigated carefully. The activity of Mn2O3 was inferior to Pt-loaded catalysts in toluene oxidation but showed superior ability for destroying acetone, while Pt loading could boost the catalytic activity of Mn2O3 for both acetone and toluene. This suitability could be determined by the physicochemical properties of the catalysts and the structure of the VOC since toluene destruction activity is highly reliant on Pt0 in the metallic state and linearly correlated with the amount of surface reactive oxygen species (Oads), while the crucial factor that affects acetone oxidation is the mobility of lattice oxygen (Olat). The Pt/Mn2O3 catalyst shows highly active Pt-O-Mn interfacial sites, favoring the generation of Oads and promoting Mn-Olat mobility, leading to its excellent performance. Therefore, the design of abundant active sites is an effective means of developing highly adaptive catalysts for the oxidation of different VOCs.
- 29 May 2023
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 62 (22) , 8665-8672
Facile Method to Create PdCe–MnOx Catalyst for Decomposing O3 under Humidity Conditions
- 29 May 2023
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 62 (22) , 8665-8672
Facile Method to Create PdCe–MnOx Catalyst for Decomposing O3 under Humidity Conditions
- Open Access
- 27 March 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Interchain Expanded Extra-Large Pore Zeolites
Stable aluminosilicate zeolites with extra-large pores open through rings of more than 12 tetrahedra are in demand to process molecules larger than those currently manageable. However, until very recently, they proved elusive. Here we report a new strategy based on an interchain expansion design concept that yields thermally and hydrothermally stable silicates by expansion of a one dimensional (1D) silicate chain with an intercalated silylating agent that separates and connects the chains. As a result, new types of zeolites zeolites with extra-large pores delimited by 20, 16, and 16 Si tetrahedra along the three crystallographic directions, respectively, are obtained. The as-made inter-chain expanded zeolite contains dangling Si-CH3 groups that by calcination connect to each other resulting in a true, fully connected 3D zeolite framework with a very low density, just slightly above that of water. Additionally, it features triple four ring units never seen before in any type of zeolite. Ti can be introduced in this zeolite to obtain a catalyst active in the liquid-phase oxidation of bulky alkenes that shows promise in the industrially relevant clean production of propylene oxide using cumene hydroperoxide as an oxidant.
- 27 March 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessInterchain Expanded Extra-Large Pore Zeolites
Stable aluminosilicate zeolites with extra-large pores open through rings of more than 12 tetrahedra are in demand to process molecules larger than those currently manageable. However, until very recently, they proved elusive. Here we report a new strategy based on an interchain expansion design concept that yields thermally and hydrothermally stable silicates by expansion of a one dimensional (1D) silicate chain with an intercalated silylating agent that separates and connects the chains. As a result, new types of zeolites zeolites with extra-large pores delimited by 20, 16, and 16 Si tetrahedra along the three crystallographic directions, respectively, are obtained. The as-made inter-chain expanded zeolite contains dangling Si-CH3 groups that by calcination connect to each other resulting in a true, fully connected 3D zeolite framework with a very low density, just slightly above that of water. Additionally, it features triple four ring units never seen before in any type of zeolite. Ti can be introduced in this zeolite to obtain a catalyst active in the liquid-phase oxidation of bulky alkenes that shows promise in the industrially relevant clean production of propylene oxide using cumene hydroperoxide as an oxidant.