Pedro Guilherme Silva Pesci
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Pedro Guilherme Silva Pesci has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Homero de Paula e Silva
Instituto de Aeronáutica e Espaço – IAE, São José dos Campos, Brazil
2 shared publications- Humberto Araujo Machado
Instituto de Aeronáutica e Espaço, Brazil; Universidade do Estado do Rio de Janeiro, Brazil
2 shared publications - Carlos Eduardo Grossi Campos
Instituto Tecnológico de Aeronáutica, Brazil; Instituto de Aeronáutica e Espaço, Brazil
1 shared publication Cristian Cley Paterniani Rita
Instituto Tecnológico da Aeronáutica – ITA, São José dos Campos, Brazil
1 shared publication- Cristian Cley Paterniani Rita
ITA, Ctr Ciencia & Tecnol Plasmas & Mat, Pr Mal Eduardo Gomes,50, BR-12228900 Sao Jose Dos Campos, SP, Brazil
1 shared publication Edson Cocchieri Botelho
Universidade Paulista, Guaratinguetá, 04026-002, BRAZIL
1 shared publication
Latest Publications
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Journal of Aerospace Technology and Management
- Vol. 18
Influence of Fiber Inclination Angle on the Mechanical and Thermal Properties of a Composite
Polymer composites have been adopted as a structural materials for solid rocket motor envelopes. The mechanical and thermal properties of these composites are strongly influenced by the orientation angle of the fibers. Due to the aerodynamic heating, accurate assessment of the effective heat and mechanical properties is crucial to the success of rocket engine designs. In this work, heat transfer simulation in the wall of a solid rocket engine envelope made of polymeric composite through the finite element method was employed to evaluate the effect of fiber inclination relative to the axis on effective thermal conductivity and effective specific heat, in conjunction with an inverse analysis technique. The results of thermal simulations improved the results and reduced the root mean square error by 12-15% in the mass loss rate, when compared to experimental results for ablation, allowing considering the methodology to be considered validated. The effective modulus of elasticity and the effective Poisson’s ratio are also evaluated, presenting an average deviation of 15.3% compared to experimental results. The results obtained show the dependence of these properties on this geometric parameter, allowing this methodology to be used as a reliable design tool for those systems.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Journal of Aerospace Technology and Management
- Vol. 18
Open AccessInfluence of Fiber Inclination Angle on the Mechanical and Thermal Properties of a Composite
Polymer composites have been adopted as a structural materials for solid rocket motor envelopes. The mechanical and thermal properties of these composites are strongly influenced by the orientation angle of the fibers. Due to the aerodynamic heating, accurate assessment of the effective heat and mechanical properties is crucial to the success of rocket engine designs. In this work, heat transfer simulation in the wall of a solid rocket engine envelope made of polymeric composite through the finite element method was employed to evaluate the effect of fiber inclination relative to the axis on effective thermal conductivity and effective specific heat, in conjunction with an inverse analysis technique. The results of thermal simulations improved the results and reduced the root mean square error by 12-15% in the mass loss rate, when compared to experimental results for ablation, allowing considering the methodology to be considered validated. The effective modulus of elasticity and the effective Poisson’s ratio are also evaluated, presenting an average deviation of 15.3% compared to experimental results. The results obtained show the dependence of these properties on this geometric parameter, allowing this methodology to be used as a reliable design tool for those systems.
- 1 May 2023
- Published by SAGE Publications in Materials Science and Technology
- Vol. 39 (8) , 972-984
A lumped mathematical model for ablation in polymeric composites
Thermal Protection Systems (TPS) are used to protect a rocket payload until it arrives intact at its destination. Reliable tools for their design must be defined. The degradation process generated by aerodynamic heating in polymeric ablators can be calculated using lumped models at low computational cost. This work presents a simplified but valid model for the ablation of polymeric composites using lumped source terms to simulate physical phenomena that occur during ablation. Reference works were considered for comparison. The model was compared to experimental results of ablative materials used by the Brazilian Space Program. Mass loss rate curves were generated and presented good agreement to the results. Evolution of ablation and pyrolysis was also evaluated through the model's results.
- 1 May 2023
- Published by SAGE Publications in Materials Science and Technology
- Vol. 39 (8) , 972-984
A lumped mathematical model for ablation in polymeric composites
Thermal Protection Systems (TPS) are used to protect a rocket payload until it arrives intact at its destination. Reliable tools for their design must be defined. The degradation process generated by aerodynamic heating in polymeric ablators can be calculated using lumped models at low computational cost. This work presents a simplified but valid model for the ablation of polymeric composites using lumped source terms to simulate physical phenomena that occur during ablation. Reference works were considered for comparison. The model was compared to experimental results of ablative materials used by the Brazilian Space Program. Mass loss rate curves were generated and presented good agreement to the results. Evolution of ablation and pyrolysis was also evaluated through the model's results.
- 16 October 2021
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 43 (11) , 1-16
The effect of environment pressure in carbon–phenolic composite ablation
- 16 October 2021
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 43 (11) , 1-16
The effect of environment pressure in carbon–phenolic composite ablation
- 18 May 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (6) , 065601
Numerical-experimental analysis of a carbon-phenolic composite via plasma jet ablation test
Materials used in space vehicles components are subjected to thermally aggressive environments when exposed to atmospheric reentry. In order to protect the payload and the vehicle itself, ablative composites are employed as TPS (Thermal Protection System). The development of TPS materials generally go through phases of obtaining, atmospheric reentry tests and comparison with a mathematical model. The state of the art presents some reentry tests in a subsonic or supersonic arc-jet facility, and a complex type of mathematical model, which normally requires large computational cost. This work presents a reliable method for estimate the performance of ablative composites, combining empirical and experimental data. Tests of composite materials used in thermal protection systems through exposure to a plasma jet are performed, where the heat fluxes emulate those present in atmospheric reentry of space vehicles components. The carbon/phenolic material samples have been performed in the hypersonic plasma tunnel of Plasma and Process Laboratory, available in Aeronautics Institute of Technology (ITA), by a plasma torch with a 50 kW DC power source. The plasma tunnel parameters were optimized to reproduce the conditions close to the critical re-entry point of the space vehicles payloads developed by the Aeronautics and Space Institute (IAE). The specimens in study were developed and manufactured in Brazil. Mass loss and specific mass loss rates of the samples and the back surface temperatures, as a function of the exposure time to the thermal flow, were determined. A computational simulation based in a two-front ablation model was performed, in order to compare the tests and the simulation results. The results allowed to estimate the ablative behavior of the tested material and to validate the theoretical model used in the computational simulation for its use in geometries close to the thermal protection systems used in the Brazilian space and suborbital vehicles.
- 18 May 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (6) , 065601
Numerical-experimental analysis of a carbon-phenolic composite via plasma jet ablation test
Materials used in space vehicles components are subjected to thermally aggressive environments when exposed to atmospheric reentry. In order to protect the payload and the vehicle itself, ablative composites are employed as TPS (Thermal Protection System). The development of TPS materials generally go through phases of obtaining, atmospheric reentry tests and comparison with a mathematical model. The state of the art presents some reentry tests in a subsonic or supersonic arc-jet facility, and a complex type of mathematical model, which normally requires large computational cost. This work presents a reliable method for estimate the performance of ablative composites, combining empirical and experimental data. Tests of composite materials used in thermal protection systems through exposure to a plasma jet are performed, where the heat fluxes emulate those present in atmospheric reentry of space vehicles components. The carbon/phenolic material samples have been performed in the hypersonic plasma tunnel of Plasma and Process Laboratory, available in Aeronautics Institute of Technology (ITA), by a plasma torch with a 50 kW DC power source. The plasma tunnel parameters were optimized to reproduce the conditions close to the critical re-entry point of the space vehicles payloads developed by the Aeronautics and Space Institute (IAE). The specimens in study were developed and manufactured in Brazil. Mass loss and specific mass loss rates of the samples and the back surface temperatures, as a function of the exposure time to the thermal flow, were determined. A computational simulation based in a two-front ablation model was performed, in order to compare the tests and the simulation results. The results allowed to estimate the ablative behavior of the tested material and to validate the theoretical model used in the computational simulation for its use in geometries close to the thermal protection systems used in the Brazilian space and suborbital vehicles.