Mariusz Kuczaj
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mariusz Kuczaj has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Andrzej Norbert Wieczorek
Faculty of Mining, Safety Engineering and Industrial Automation, Silesian University of Technology, Akademicka 2 Street, 44-100 Gliwice, Poland
13 shared publications - Krzysztof Filipowicz
Faculty of Mining, Safety Engineering and Industrial Automation, Silesian University of Technology, Akademicka 2 Street, 44-100 Gliwice, Poland
13 shared publications - Arkadiusz Pawlikowski
Faculty of Mining, Safety Engineering and Industrial Automation, Silesian University of Technology, Akademicka 2 Street, 44-100 Gliwice, Poland
10 shared publications - Iwona Jonczy
Faculty of Mining, Safety Engineering and Industrial Automation, Silesian University of Technology, Akademicka 2 Street, 44-100 Gliwice, Poland
7 shared publications - Anna Gerle
Łukasiewicz Research Network – Institute of Ceramics and Building Materials, Poland
4 shared publications - Grzegorz Wojnar
Department of Road Transport, Faculty of Transport and Aviation Engineering, Silesian University of Technology, 40-019 Katowice, Poland
4 shared publications
Latest Publications
- Open Access
Effect of Carbonaceous Contaminants with Different Degrees of Carbonization on the Wear of 42CrMo4 Steel Under Boundary Lubrication
The aim of this study was to analyse the quantitative and qualitative effects of mineral oil contamination in the form of crushed hard coal and coal shale particles on the tribological wear of 42CrMo-4 steel under boundary lubrication conditions. The tests were conducted using a roller-on-roller tribological test rig, and the surfaces were analysed by SEM, XRF, EDS, XRD, Raman spectroscopy, and profilometry. An analysis of the impact of carbon and clay contaminants in mineral oil on the wear of 42CrMo-4 steel showed that the degree of carbonization of the added carbon and the mineral fraction content jointly influenced the thermochemical behaviour of the contaminants and the intensity of surface wear. Variant 1, containing carbon with a medium degree of carbonization and low mineral content, exhibited the lowest wear, with a spalling depth of approximately 10 µm—about 25% of the values observed for the other variants—and a wear rate approximately 12.5 times lower than that of the other variants. The favourable may be associated with carbon plasticization and the formation of a protective carbon-rich layer that limited direct interaction between surface asperities. In Variants 2–5, most likely formed more brittle transformation products that did not provide comparable surface protection, resulting in deeper spalling. EDS analysis revealed carbon-rich particles on the surface tested under Variant 0 conditions, indirectly supporting the possibility of thermal oil degradation and high local contact temperatures.
Open AccessEffect of Carbonaceous Contaminants with Different Degrees of Carbonization on the Wear of 42CrMo4 Steel Under Boundary Lubrication
The aim of this study was to analyse the quantitative and qualitative effects of mineral oil contamination in the form of crushed hard coal and coal shale particles on the tribological wear of 42CrMo-4 steel under boundary lubrication conditions. The tests were conducted using a roller-on-roller tribological test rig, and the surfaces were analysed by SEM, XRF, EDS, XRD, Raman spectroscopy, and profilometry. An analysis of the impact of carbon and clay contaminants in mineral oil on the wear of 42CrMo-4 steel showed that the degree of carbonization of the added carbon and the mineral fraction content jointly influenced the thermochemical behaviour of the contaminants and the intensity of surface wear. Variant 1, containing carbon with a medium degree of carbonization and low mineral content, exhibited the lowest wear, with a spalling depth of approximately 10 µm—about 25% of the values observed for the other variants—and a wear rate approximately 12.5 times lower than that of the other variants. The favourable may be associated with carbon plasticization and the formation of a protective carbon-rich layer that limited direct interaction between surface asperities. In Variants 2–5, most likely formed more brittle transformation products that did not provide comparable surface protection, resulting in deeper spalling. EDS analysis revealed carbon-rich particles on the surface tested under Variant 0 conditions, indirectly supporting the possibility of thermal oil degradation and high local contact temperatures.
- Open Access
- 8 May 2026
- Published by Stowarzyszenie Menedzerow Jakosci i Produkcji in Production Engineering Archives
- Vol. 32 (2) , 302-315
Operation-oriented numerical analysis of dynamic loads occurring in drive units of armoured face conveyors with an innovative highly flexible coupling
For many years, the hard coal mining industry has been searching for engineering solutions ensuring greater reliability of the machines operating in difficult underground conditions. The foregoing applies in particular to the scraper conveyors used in longwall systems, started up very frequently and exposed to variable dynamic loads, leading to accelerated wear of powertrain components. The authors of this study have developed a longwall scraper conveyor equipped with a torsionally flexible metal clutch of novel design. The article provides a description of a mathematical model of a conveyor featuring two centrally arranged chains along with a main (discharge) and auxiliary (return) drive, as well as results of the computer simulations performed for two variants of the drive system setup analysed: one with a typical flexible clutch and the other with the innovative torsionally flexible clutch. Analysis of these results has revealed that the solution proposed significantly reduces the amplitude of dynamic loads, which contributes to increased durability and reliability of conveyors under mining conditions.
- 8 May 2026
- Published by Stowarzyszenie Menedzerow Jakosci i Produkcji in Production Engineering Archives
- Vol. 32 (2) , 302-315
Open AccessOperation-oriented numerical analysis of dynamic loads occurring in drive units of armoured face conveyors with an innovative highly flexible coupling
For many years, the hard coal mining industry has been searching for engineering solutions ensuring greater reliability of the machines operating in difficult underground conditions. The foregoing applies in particular to the scraper conveyors used in longwall systems, started up very frequently and exposed to variable dynamic loads, leading to accelerated wear of powertrain components. The authors of this study have developed a longwall scraper conveyor equipped with a torsionally flexible metal clutch of novel design. The article provides a description of a mathematical model of a conveyor featuring two centrally arranged chains along with a main (discharge) and auxiliary (return) drive, as well as results of the computer simulations performed for two variants of the drive system setup analysed: one with a typical flexible clutch and the other with the innovative torsionally flexible clutch. Analysis of these results has revealed that the solution proposed significantly reduces the amplitude of dynamic loads, which contributes to increased durability and reliability of conveyors under mining conditions.
- Open Access
- 30 December 2025
- Published by MDPI AG in Preprints.org
Numerical Study of the Dynamic Loads Observed in the Drive Units of Scraper Conveyors Featuring an Innovative Clutch
For many years, the hard coal mining industry has been searching for engineering solutions ensuring greater reliability of the machines operating in difficult underground conditions. The foregoing applies in particular to the scraper conveyors used in longwall systems, started up very frequently and exposed to variable dynamic loads, leading to accelerated wear of powertrain components. The authors of this study have developed a longwall scraper conveyor equipped with a torsionally flexible metal clutch of novel design. The article provides a description of a mathematical model of a conveyor featuring two centrally arranged chains along with a main (discharge) and auxiliary (return) drive, as well as results of the computer simulations performed for two variants of the drive system setup analysed: one with a typical flexible clutch and the other with the innovative torsionally flexible clutch. Analysis of these results has revealed that the solution proposed significantly reduces the amplitude of dyna mic loads, which contributes to increased durability and reliability of conveyors under mining conditions.
- 30 December 2025
- Published by MDPI AG in Preprints.org
Open AccessNumerical Study of the Dynamic Loads Observed in the Drive Units of Scraper Conveyors Featuring an Innovative Clutch
For many years, the hard coal mining industry has been searching for engineering solutions ensuring greater reliability of the machines operating in difficult underground conditions. The foregoing applies in particular to the scraper conveyors used in longwall systems, started up very frequently and exposed to variable dynamic loads, leading to accelerated wear of powertrain components. The authors of this study have developed a longwall scraper conveyor equipped with a torsionally flexible metal clutch of novel design. The article provides a description of a mathematical model of a conveyor featuring two centrally arranged chains along with a main (discharge) and auxiliary (return) drive, as well as results of the computer simulations performed for two variants of the drive system setup analysed: one with a typical flexible clutch and the other with the innovative torsionally flexible clutch. Analysis of these results has revealed that the solution proposed significantly reduces the amplitude of dyna mic loads, which contributes to increased durability and reliability of conveyors under mining conditions.
- Open Access
- 12 November 2025
- Published by MDPI AG in Preprints.org
Study on the Effect of Coal and Claystone Particles in Lubricating Oil on the Wear of the 42CrMo-4 Steel Under Mixed Lubrication
The aim of the study was to analyse the impact of carbonaceous and mineral contami-nants present in mineral oils on the tribological wear of the 42CrMo-4 steel under mixed friction conditions. A range of advanced analytical techniques was employed, including polarised light optical microscopy, SEM, XRF, EDS, XRD, as well as Raman spectroscopy and profilometry. Wear tests were conducted using a roller-on-roller tribological test rig to evaluate changes in surface topography and the extent of surface damage. The results showed no clear functional correlation between the mass loss of the samples and the con-tent of non-combustible fractions in the carbonaceous contaminants. The most favourable tribological performance was observed for the abrasive variant with low ash content and high elemental carbon content. In this case, a thin graphite-like carbon layer formed on the surface, significantly improving lubrication, reducing friction, limiting surface spalling, and reducing damage depth (to approx. 10 µm). In other variants, despite the formation of compressed carbon–mineral layers, the higher content of hard mineral particles reduced their durability and led to increased wear. Local temperature and particle size were found to significantly influence wear intensity – smaller particles contributed to lower flash temperatures and reduced surface damage. The variant with pure oil, lacking any abra-sive additives, showed no protective effects, resulting in intense microscratching and sur-face spalling due to direct asperity contact.
- 12 November 2025
- Published by MDPI AG in Preprints.org
Open AccessStudy on the Effect of Coal and Claystone Particles in Lubricating Oil on the Wear of the 42CrMo-4 Steel Under Mixed Lubrication
The aim of the study was to analyse the impact of carbonaceous and mineral contami-nants present in mineral oils on the tribological wear of the 42CrMo-4 steel under mixed friction conditions. A range of advanced analytical techniques was employed, including polarised light optical microscopy, SEM, XRF, EDS, XRD, as well as Raman spectroscopy and profilometry. Wear tests were conducted using a roller-on-roller tribological test rig to evaluate changes in surface topography and the extent of surface damage. The results showed no clear functional correlation between the mass loss of the samples and the con-tent of non-combustible fractions in the carbonaceous contaminants. The most favourable tribological performance was observed for the abrasive variant with low ash content and high elemental carbon content. In this case, a thin graphite-like carbon layer formed on the surface, significantly improving lubrication, reducing friction, limiting surface spalling, and reducing damage depth (to approx. 10 µm). In other variants, despite the formation of compressed carbon–mineral layers, the higher content of hard mineral particles reduced their durability and led to increased wear. Local temperature and particle size were found to significantly influence wear intensity – smaller particles contributed to lower flash temperatures and reduced surface damage. The variant with pure oil, lacking any abra-sive additives, showed no protective effects, resulting in intense microscratching and sur-face spalling due to direct asperity contact.
- Open Access
- 3 November 2025
- Published by Walter de Gruyter GmbH in Management Systems in Production Engineering
- Vol. 33 (4) , 478-485
Tests of Shearing Mechanism of Safety Pins Used in Safety Couplings
The paper presents an analysis of issues related to improper shearing of safety pins used in overload couplings. Based on FEM computer simulations, it was established that the highest values of destructive stresses occur at the site of the structural narrowing. Experiments regarding the shearing of safety pins were carried out on a specialized test stand. 4 batches of pins of different hardness and 1 batch of reference pins were subjected to strength tests. Based on the conducted tests, it was established that the hardness of the pin material, which defines the form of the separating fracture, has a significant impact on the correct shear process of the pins. The paper also presents technological and design recommendations that should ensure an appropriate form of decohesion of the safety pin.
- 3 November 2025
- Published by Walter de Gruyter GmbH in Management Systems in Production Engineering
- Vol. 33 (4) , 478-485
Open AccessTests of Shearing Mechanism of Safety Pins Used in Safety Couplings
The paper presents an analysis of issues related to improper shearing of safety pins used in overload couplings. Based on FEM computer simulations, it was established that the highest values of destructive stresses occur at the site of the structural narrowing. Experiments regarding the shearing of safety pins were carried out on a specialized test stand. 4 batches of pins of different hardness and 1 batch of reference pins were subjected to strength tests. Based on the conducted tests, it was established that the hardness of the pin material, which defines the form of the separating fracture, has a significant impact on the correct shear process of the pins. The paper also presents technological and design recommendations that should ensure an appropriate form of decohesion of the safety pin.
- 22 September 2025
- Published by Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne in Eksploatacja i Niezawodność – Maintenance and Reliability
- Vol. 27 (4)
Variation analysis of a drive system with an innovative flexible clutch operating under the conditions of constant and cyclically variable load torque of diverse variation waveform
During machinery operation, load is often highly variable, which exerts an impact on how the machinery service life is reduced; hence the need for decreasing the variations in the load torque affecting the driving elements of machines. In order to achieve such reduction, the authors have developed a flexible clutch of innovative design. This paper provides a follow-up to the studies of the dynamic properties of the said clutch in terms of the analysis of the effect attributable to the input function waveform of the applied load on the dynamic response of the system, represented by the value of the accelerations of the drive system vibrations. The load variants analysed, with values of 500±250 Nm and 750±375 Nm (sinusoidal, triangular, and rectangular waveforms). On account of the fact that the flexible clutch was integrated with the drive system subject to the studies, it was found that the averaged maximum root mean square reductions of vibration accelerations in the measurement direction with the highest vibration accelerations (direction y) came as high as to 56.1%.
- 22 September 2025
- Published by Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne in Eksploatacja i Niezawodność – Maintenance and Reliability
- Vol. 27 (4)
Variation analysis of a drive system with an innovative flexible clutch operating under the conditions of constant and cyclically variable load torque of diverse variation waveform
During machinery operation, load is often highly variable, which exerts an impact on how the machinery service life is reduced; hence the need for decreasing the variations in the load torque affecting the driving elements of machines. In order to achieve such reduction, the authors have developed a flexible clutch of innovative design. This paper provides a follow-up to the studies of the dynamic properties of the said clutch in terms of the analysis of the effect attributable to the input function waveform of the applied load on the dynamic response of the system, represented by the value of the accelerations of the drive system vibrations. The load variants analysed, with values of 500±250 Nm and 750±375 Nm (sinusoidal, triangular, and rectangular waveforms). On account of the fact that the flexible clutch was integrated with the drive system subject to the studies, it was found that the averaged maximum root mean square reductions of vibration accelerations in the measurement direction with the highest vibration accelerations (direction y) came as high as to 56.1%.
- Open Access
Effect of the Mineralogical Composition of Sandstones on the Wear of Mining Machinery Components
The paper provides and comments on the results of studies of the effect of sandstone-based abrasives and quartz sand alone on the wear of martensitic surfaces of wear-resistant steels. The wear process was examined on a ring-on-ring test rig seeking to determine the mass decrement parameter which characterised wear. In addition, SEM microscopy, optical profilometry and XRF analysis were used to analyse the abrasives used and damaged surfaces. The tests were conducted for three sandstone varieties, Carboniferous, Permian, and Cretaceous, and they made it possible to determine that the most intense process of deterioration of wear-resistant steels took place in the presence of quartz sand grain, while less intense wear was observed in the case of sandstone-based abrasives. The mass decrement values established in the presence of the sandstones in question did not differ significantly between individual sandstone varieties. Based on a surface damage analysis, the basic damage mechanism was found to be micro-scratching; however, with regard to the sandstones examined, it was also determined that individual grains could be pressed into surface irregularities and that films of soft hematite cement developed in the Permian sandstone and that inclusions of carbonaceous matter were formed in the Carboniferous sandstone. With reference to the wear process observations, a wear model was described for the surface of the steels examined in the presence of sandstone-based abrasives. This model presents the possibility of capturing wear products by unstable binder layers and changing the form of wear from three-body to two-body.
Open AccessEffect of the Mineralogical Composition of Sandstones on the Wear of Mining Machinery Components
The paper provides and comments on the results of studies of the effect of sandstone-based abrasives and quartz sand alone on the wear of martensitic surfaces of wear-resistant steels. The wear process was examined on a ring-on-ring test rig seeking to determine the mass decrement parameter which characterised wear. In addition, SEM microscopy, optical profilometry and XRF analysis were used to analyse the abrasives used and damaged surfaces. The tests were conducted for three sandstone varieties, Carboniferous, Permian, and Cretaceous, and they made it possible to determine that the most intense process of deterioration of wear-resistant steels took place in the presence of quartz sand grain, while less intense wear was observed in the case of sandstone-based abrasives. The mass decrement values established in the presence of the sandstones in question did not differ significantly between individual sandstone varieties. Based on a surface damage analysis, the basic damage mechanism was found to be micro-scratching; however, with regard to the sandstones examined, it was also determined that individual grains could be pressed into surface irregularities and that films of soft hematite cement developed in the Permian sandstone and that inclusions of carbonaceous matter were formed in the Carboniferous sandstone. With reference to the wear process observations, a wear model was described for the surface of the steels examined in the presence of sandstone-based abrasives. This model presents the possibility of capturing wear products by unstable binder layers and changing the form of wear from three-body to two-body.
- Open Access
- 27 May 2024
- Published by MDPI AG in Preprints.org
Effect of the Mineralogical Composition of Sandstones on the Wear of Mining Machinery Components
The paper provides and comments on the results of studies of the effect of sandstone-based abrasives and quartz sand alone on the wear of martensitic surfaces of wear-resistant steels. The wear process was examined on a ring-on-ring test rig seeking to determine the mass decrement parameter which characterised wear. The tests were conducted for three sandstone varieties: Carboniferous, Permian, and Cretaceous, and they made it possible to determine that the most intense process of deterioration of wear-resistant steels took place in the presence of quartz sand grain, while less intense wear was observed in the case of sandstone-based abrasives. The mass decrement values established in the presence of the sandstones in question did not differ significantly between individual sandstone varieties. Based on a surface damage analysis, the basic damage mechanism was found to be micro-scratching, however, with regard to the sandstones examined, it was also determined that individual grains could be pressed into surface irregularities, as well as that films of soft hematite cement developed in the Permian sandstone and that inclusions of carbonaceous matter were formed in the Carboniferous sandstone. With reference to the wear process observations, a wear model was described for the surface of the steels examined in the presence of sandstone-based abrasives.
- 27 May 2024
- Published by MDPI AG in Preprints.org
Open AccessEffect of the Mineralogical Composition of Sandstones on the Wear of Mining Machinery Components
The paper provides and comments on the results of studies of the effect of sandstone-based abrasives and quartz sand alone on the wear of martensitic surfaces of wear-resistant steels. The wear process was examined on a ring-on-ring test rig seeking to determine the mass decrement parameter which characterised wear. The tests were conducted for three sandstone varieties: Carboniferous, Permian, and Cretaceous, and they made it possible to determine that the most intense process of deterioration of wear-resistant steels took place in the presence of quartz sand grain, while less intense wear was observed in the case of sandstone-based abrasives. The mass decrement values established in the presence of the sandstones in question did not differ significantly between individual sandstone varieties. Based on a surface damage analysis, the basic damage mechanism was found to be micro-scratching, however, with regard to the sandstones examined, it was also determined that individual grains could be pressed into surface irregularities, as well as that films of soft hematite cement developed in the Permian sandstone and that inclusions of carbonaceous matter were formed in the Carboniferous sandstone. With reference to the wear process observations, a wear model was described for the surface of the steels examined in the presence of sandstone-based abrasives.
- 17 January 2024
- Published by Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne in Eksploatacja i Niezawodność – Maintenance and Reliability
- Vol. 26 (2)
Reduction of dynamic loads in the drive system of mining scraper conveyors through the use of an innovative highly flexible metal coupling
The article provides a discussion on the results of the original studies of a power transmission system of a mining scraper conveyor coupled with an innovative highly flexible clutch, conducted in operating conditions. The research consisted in establishing the static characteristics of the...
- 17 January 2024
- Published by Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne in Eksploatacja i Niezawodność – Maintenance and Reliability
- Vol. 26 (2)
Reduction of dynamic loads in the drive system of mining scraper conveyors through the use of an innovative highly flexible metal coupling
The article provides a discussion on the results of the original studies of a power transmission system of a mining scraper conveyor coupled with an innovative highly flexible clutch, conducted in operating conditions. The research consisted in establishing the static characteristics of the...
- Open Access
Study of the Impact of Coals and Claystones on Wear-Resistant Steels
This paper discusses the impact of coal abrasive materials of varied petrographic composition and claystones containing admixtures of coal matter on the surface wear of wear-resistant martensitic steels. Wear tests were conducted at a test stand for three petrographic varieties of hard coal: vitrinite, clarinite, and durinite, and five samples of claystone. These tests revealed no significant effect of the type of coal abrasive used on the value of mass loss from the surface of the wear-resistant steel samples. The reason behind the foregoing is the observed tendency of coal abrasives, irrespective of their petrographic variety, to penetrate surface irregularities, especially those attributable to previous surface treatment of the samples and the impact of wear products. The dominant forms of surface damage were surface fatigue chipping and scratches caused by the particles which detached themselves from the surface of the steel samples, as observed for all the analysed coal variants. On the surfaces of the samples seasoned in the presence of claystones, highly varied forms of damage were observed: microcutting, scaly surface cracks, delamination, and deep cracks. In these cases, it was possible that the abrasive grains had been pressed into the steel surface irregularities, but no layered forms of the pressed-in abrasive material were observed to have developed. The paper also presents a model for the formation of coal films and discusses their possible effect on wear minimisation.
Open AccessStudy of the Impact of Coals and Claystones on Wear-Resistant Steels
This paper discusses the impact of coal abrasive materials of varied petrographic composition and claystones containing admixtures of coal matter on the surface wear of wear-resistant martensitic steels. Wear tests were conducted at a test stand for three petrographic varieties of hard coal: vitrinite, clarinite, and durinite, and five samples of claystone. These tests revealed no significant effect of the type of coal abrasive used on the value of mass loss from the surface of the wear-resistant steel samples. The reason behind the foregoing is the observed tendency of coal abrasives, irrespective of their petrographic variety, to penetrate surface irregularities, especially those attributable to previous surface treatment of the samples and the impact of wear products. The dominant forms of surface damage were surface fatigue chipping and scratches caused by the particles which detached themselves from the surface of the steel samples, as observed for all the analysed coal variants. On the surfaces of the samples seasoned in the presence of claystones, highly varied forms of damage were observed: microcutting, scaly surface cracks, delamination, and deep cracks. In these cases, it was possible that the abrasive grains had been pressed into the steel surface irregularities, but no layered forms of the pressed-in abrasive material were observed to have developed. The paper also presents a model for the formation of coal films and discusses their possible effect on wear minimisation.