Barbara Maria Świtała
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Barbara Maria Świtała has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Wei Wu
Institute of Geotechnical Engineering, Boku University, Vienna, Austria
7 shared publications - Danuta Leśniewska
Koszalin University of Technology
2 shared publications A. Askarinejad
Faculty of Civil Engineering and Geosciences, TU Delft, CN Delft, the Netherlands
1 shared publication- Carlotta Guardiani
University of Natural Resources and Life Sciences
1 shared publication E. J. Fern
Department of Civil and Environmental Engineering, University of California, Berkeley
1 shared publicationE. James Fern
University of California
1 shared publication
Latest Publications
- Open Access
- 19 December 2025
- Published by Springer Nature in Granular Matter
- Vol. 28 (1) , 13
Image brightness analysis as a tool for strain measurement in photo-elastic compression tests on PDMS granulate
The paper presents the behaviour of samples made of self-manufactured polydimethylsiloxane (PDMS) grains in a photo-elastic confined uniaxial compression test. PDMS particles were produced using the water-based method, resulting in grain shapes that are close to spherical, with diameters ranging from 2.0 to 16.0 mm. The samples tested were of the same size; however, they consisted of grains of different fractions, diameter spans, and aspect ratios relative to the dimensions of the test box. They were subjected to a load-unload cycle according to several scenarios, first to determine the load that induces a measurable photo-elastic effect. To study the potential relationship between the uniaxial strain calculated based on the change in a sample’s height and the corresponding optical parameters, a parallel analysis was conducted using the average image brightness. It led to the proposal of standardised strain and brightness parameters, which reduced the influence of loading scenarios and camera settings on the test results, allowing for the study of the other factors. On this basis, a unique relationship has been found between normalised uniaxial strain and normalised relative average image brightness, encompassing both loading and unloading regimes. In contrast, two calibration curves are required to calculate stress from brightness. The most interesting finding is that, despite the different force network structures observed in the uniaxial compression test, they do not appear to affect the behaviour of the granular samples on a macro-scale. Graphical abstract
- 19 December 2025
- Published by Springer Nature in Granular Matter
- Vol. 28 (1) , 13
Open AccessImage brightness analysis as a tool for strain measurement in photo-elastic compression tests on PDMS granulate
The paper presents the behaviour of samples made of self-manufactured polydimethylsiloxane (PDMS) grains in a photo-elastic confined uniaxial compression test. PDMS particles were produced using the water-based method, resulting in grain shapes that are close to spherical, with diameters ranging from 2.0 to 16.0 mm. The samples tested were of the same size; however, they consisted of grains of different fractions, diameter spans, and aspect ratios relative to the dimensions of the test box. They were subjected to a load-unload cycle according to several scenarios, first to determine the load that induces a measurable photo-elastic effect. To study the potential relationship between the uniaxial strain calculated based on the change in a sample’s height and the corresponding optical parameters, a parallel analysis was conducted using the average image brightness. It led to the proposal of standardised strain and brightness parameters, which reduced the influence of loading scenarios and camera settings on the test results, allowing for the study of the other factors. On this basis, a unique relationship has been found between normalised uniaxial strain and normalised relative average image brightness, encompassing both loading and unloading regimes. In contrast, two calibration curves are required to calculate stress from brightness. The most interesting finding is that, despite the different force network structures observed in the uniaxial compression test, they do not appear to affect the behaviour of the granular samples on a macro-scale. Graphical abstract
- Open Access
- 18 July 2024
- Published by Elsevier in Computers and Geotechnics
- Vol. 174
Micro-mechanisms of force network rearrangement in granular materials
- 18 July 2024
- Published by Elsevier in Computers and Geotechnics
- Vol. 174
Open AccessMicro-mechanisms of force network rearrangement in granular materials
- 1 December 2023
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 60 (12) , 1877-1894
Machine learning-aided reliability analysis of rainfall-induced landslide of root-reinforced slopes
Estimating the failure probability of rainfall-induced landslides is often challenging as the triggering mechanism is influenced by a number of parameters whose uncertainty is difficult to quantify and, in practice, is neglected. The reinforcing effect of vegetation on natural slopes adds to the complexity of the stability analysis. In this study, we present the application of a coupled hydro-mechanical model for the effect of plant roots on soil shear strength. First, a deterministic approach is adopted. Then, a reliability analysis of a root-reinforced slope subjected to rainfall is performed by considering the inherent variability of the soil and root properties. The probability of failure is estimated with machine learning surrogate models, which approximate the nonlinear relationship between constitutive parameters and slope displacements at different time steps. The machine learning algorithms are trained on a small dataset. The extreme gradient boosting is the best-performing algorithm with R2 ≥ 0.975 and is then employed to estimate the probability of failure on a larger dataset of one million datapoints with higher accuracy.
- 1 December 2023
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 60 (12) , 1877-1894
Machine learning-aided reliability analysis of rainfall-induced landslide of root-reinforced slopes
Estimating the failure probability of rainfall-induced landslides is often challenging as the triggering mechanism is influenced by a number of parameters whose uncertainty is difficult to quantify and, in practice, is neglected. The reinforcing effect of vegetation on natural slopes adds to the complexity of the stability analysis. In this study, we present the application of a coupled hydro-mechanical model for the effect of plant roots on soil shear strength. First, a deterministic approach is adopted. Then, a reliability analysis of a root-reinforced slope subjected to rainfall is performed by considering the inherent variability of the soil and root properties. The probability of failure is estimated with machine learning surrogate models, which approximate the nonlinear relationship between constitutive parameters and slope displacements at different time steps. The machine learning algorithms are trained on a small dataset. The extreme gradient boosting is the best-performing algorithm with R2 ≥ 0.975 and is then employed to estimate the probability of failure on a larger dataset of one million datapoints with higher accuracy.
- Open Access
- 1 June 2023
- Published by Walter de Gruyter GmbH in Architecture, Civil Engineering, Environment
- Vol. 16 (2) , 151-159
Strength Reduction Method in the Stability Assessment of Vegetated Slopes
The thoughtful design and mitigation of ecological slope stabilization measures rely heavily on the reliable assessment of the stability of vegetated slopes. This is a complex problem due to the many aspects of vegetation presence that must be taken into account. The numerical model should be able to consider mechanical root reinforcement and root water uptake, which can lead to soil desaturation. This paper presents the application of the strength reduction method to the Modified Cam-Clay model for unsaturated, root-reinforced soils, which allows for the quantitative estimation of slope stability. The technique is implemented in finite element software and tested using several numerical examples. Firstly, the sensitivity of the factor of safety to changes in root constitutive parameters is investigated. In the second example, the stability of the modelled slope is assessed under rainfall of a certain duration followed by progressively modifying soil strength parameters until failure occurs. Furthermore, slope stability is assessed for various durations of the rainfall period.
- 1 June 2023
- Published by Walter de Gruyter GmbH in Architecture, Civil Engineering, Environment
- Vol. 16 (2) , 151-159
Open AccessStrength Reduction Method in the Stability Assessment of Vegetated Slopes
The thoughtful design and mitigation of ecological slope stabilization measures rely heavily on the reliable assessment of the stability of vegetated slopes. This is a complex problem due to the many aspects of vegetation presence that must be taken into account. The numerical model should be able to consider mechanical root reinforcement and root water uptake, which can lead to soil desaturation. This paper presents the application of the strength reduction method to the Modified Cam-Clay model for unsaturated, root-reinforced soils, which allows for the quantitative estimation of slope stability. The technique is implemented in finite element software and tested using several numerical examples. Firstly, the sensitivity of the factor of safety to changes in root constitutive parameters is investigated. In the second example, the stability of the modelled slope is assessed under rainfall of a certain duration followed by progressively modifying soil strength parameters until failure occurs. Furthermore, slope stability is assessed for various durations of the rainfall period.
- 1 November 2020
- Published by American Society of Civil Engineers (ASCE) in International Journal of Geomechanics
- Vol. 20 (11) , 04020206
Numerical Simulations of Triaxial Tests on Soil-Root Composites and Extension to Practical Problem: Rainfall-Induced Landslide
Root reinforcement is an interesting and environmentally favorable measure for soil stabilization. When properly applied, it can improve soil strength significantly. The paper presents a simulation of a series of drained triaxial tests on soil samples with different levels of root reinforcement in a form of three 5-mm-thick layers, located on different heights. Modified Cam-clay extended for unsaturated soils containing plant roots is used in calculations. The tests are modeled numerically and the results are compared with experimental results from the literature. Missing soil and root parameters are obtained based on the model calibration and further applied in the calculations of the stability of the vegetated slope subjected to rainfall. The influence of the initial root mass in the reinforcing superficial soil layer on the time after which a landslide occurs is investigated. The results suggest that even a minor level of root reinforcement may postpone the development of a rainfall-induced landslide.
- 1 November 2020
- Published by American Society of Civil Engineers (ASCE) in International Journal of Geomechanics
- Vol. 20 (11) , 04020206
Numerical Simulations of Triaxial Tests on Soil-Root Composites and Extension to Practical Problem: Rainfall-Induced Landslide
Root reinforcement is an interesting and environmentally favorable measure for soil stabilization. When properly applied, it can improve soil strength significantly. The paper presents a simulation of a series of drained triaxial tests on soil samples with different levels of root reinforcement in a form of three 5-mm-thick layers, located on different heights. Modified Cam-clay extended for unsaturated soils containing plant roots is used in calculations. The tests are modeled numerically and the results are compared with experimental results from the literature. Missing soil and root parameters are obtained based on the model calibration and further applied in the calculations of the stability of the vegetated slope subjected to rainfall. The influence of the initial root mass in the reinforcing superficial soil layer on the time after which a landslide occurs is investigated. The results suggest that even a minor level of root reinforcement may postpone the development of a rainfall-induced landslide.
- 1 August 2019
- Published by Elsevier in Computers and Geotechnics
- Vol. 112, 197-203
Implementation of a coupled hydro-mechanical model for root-reinforced soils in finite element code
- 1 August 2019
- Published by Elsevier in Computers and Geotechnics
- Vol. 112, 197-203
Implementation of a coupled hydro-mechanical model for root-reinforced soils in finite element code
- Open Access
- 12 July 2018
- Published by Warsaw University of Life Sciences - SGGW Press in Scientific Review Engineering and Environmental Sciences (SREES)
- Vol. 27 (2) , 103-113
Constitutive modelling of root-reinforced granular soils – preliminary studies
A novel solution for the problem of modelling of soil reinforced with vegetation roots. An extension of the Nor–Sand model and its application to granular saturated or dry, soil–root composites. Model implementation in MATLAB: numerical simulations of drained triaxial compression tests, investigation of the sensitivity of the solution to different values of model parameters. Capturing the most important features of soil–root composites. Accounting for the progressive activation of the root’s strength. Indication of the ability of further model application to large-scale problems, such as slope or dune stability.
- 12 July 2018
- Published by Warsaw University of Life Sciences - SGGW Press in Scientific Review Engineering and Environmental Sciences (SREES)
- Vol. 27 (2) , 103-113
Open AccessConstitutive modelling of root-reinforced granular soils – preliminary studies
A novel solution for the problem of modelling of soil reinforced with vegetation roots. An extension of the Nor–Sand model and its application to granular saturated or dry, soil–root composites. Model implementation in MATLAB: numerical simulations of drained triaxial compression tests, investigation of the sensitivity of the solution to different values of model parameters. Capturing the most important features of soil–root composites. Accounting for the progressive activation of the root’s strength. Indication of the ability of further model application to large-scale problems, such as slope or dune stability.
- 2 June 2018
- Published by Springer Nature
- p. 187-196
Simulation of Rainfall-Induced Landslide of the Vegetated Slope
- 2 June 2018
- Published by Springer Nature
- p. 187-196
Simulation of Rainfall-Induced Landslide of the Vegetated Slope
- 1 June 2018
- Published by Emerald Publishing in Géotechnique
- Vol. 68 (6) , 481-491
Numerical modelling of rainfall-induced instability of vegetated slopes
Vegetation is known to play an important role in reducing landslide hazard. This paper presents a numerical model, which allows modelling of rainfall-induced instabilities of vegetated slopes. Both the mechanical reinforcement and the water uptake by plant roots are taken into account by considering a coupled mechanical–hydrological system. A modified Cam-Clay model for unsaturated soil is used. The mechanical reinforcement of roots is simulated by its contribution to the preconsolidation pressure. The water uptake is modelled by a sink term for variably saturated flow. The numerical model is implemented in two finite-element codes for two- and three-dimensional problems. The model performance is demonstrated by two numerical examples.
- 1 June 2018
- Published by Emerald Publishing in Géotechnique
- Vol. 68 (6) , 481-491
Numerical modelling of rainfall-induced instability of vegetated slopes
Vegetation is known to play an important role in reducing landslide hazard. This paper presents a numerical model, which allows modelling of rainfall-induced instabilities of vegetated slopes. Both the mechanical reinforcement and the water uptake by plant roots are taken into account by considering a coupled mechanical–hydrological system. A modified Cam-Clay model for unsaturated soil is used. The mechanical reinforcement of roots is simulated by its contribution to the preconsolidation pressure. The water uptake is modelled by a sink term for variably saturated flow. The numerical model is implemented in two finite-element codes for two- and three-dimensional problems. The model performance is demonstrated by two numerical examples.