DPDiego Silva Prado

Diego Silva Prado

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Diego Silva Prado has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Topology optimization of adsorption beds using a decoupled thermal reduced-physics model and Eikonal-based penalization

    by Felipe Silva Maffei, Diego Silva Prado, Enzo Sampronha, Marcelo Martins Seckler, José Luís de Paiva, Emílio Carlos Nelli Silva

  • Open Access

    Topology Optimization of Adsorption Beds Using a Decoupled Thermal Surrogate Model and Eikonal-based Penalization

    by Felipe Maffei, Diego Silva Prado, Enzo Sampronha, Marcelo Martins Seckler, José Luís de Paiva, Emílio Carlos Nelli Silva

    Adsorbed natural gas (ANG) is a promising technology that can contribute to reducing the carbon footprint of the oil industry. This is because the ANG operates at a lower pressure relative to traditional methods. Topology optimization enables the generation of non-intuitive designs of adsorptive natural gas storage systems by inserting internal metallic structures to enhance thermal management. However, its application to adsorbent beds is often hindered by high computational cost and numerical instabilities when solving the fully coupled multiphysics problem. This work proposes a novel surrogate-based methodology that decouples the forward problem from the optimization stage. A steady-state heat conduction model, driven by transient heat-source profiles extracted from a single full-physics simulation, is used for topology optimization. In addition, to prevent non-physical material placement near boundaries that can arise from the simplified model, an Eikonal-based penalization function is introduced to define exclusion zones systematically. The approach is implemented in COMSOL Multiphysics\textsuperscript{\tiny\textregistered} with the full physics (Navier-Stokes and adsorption model) simulation validated using experimental data. Results show that optimized fin-like structures increase gas storage capacity by up to 7.6\% under specific volume fractions and filter sizes. Dimensionless analysis reveals that the Biot number serves as a threshold for the effectiveness of optimization, whereas the Fourier number governs the optimized loading cycle duration. The proposed method significantly reduces computational effort while preserving essential physics, providing a viable and generalizable framework for designing advanced adsorption vessels.

  • Topology optimization of time dependent gas–solid flow using Euler–Euler model with gravity

    by Diego Silva Prado, Luís F.N. Sá, Fereshteh Razmara, José Luís Paiva, Marcelo M. Seckler, Emílio C.N. Silva


  • Open Access

    Innovative Use of UHPC and Topology Optimization in Permeable Interlocking Pavers: Advancing Sustainable Pavement Solutions

    by Fernanda Gadler, José Augusto Ferreira Sales de Mesquita, Francisco Helio Alencar Oliveira, Liedi Legi Bariani Bernucci, Rafael Giuliano Pileggi, Emilio Carlos Nelli Silva, Diego Silva Prado

    The rapid expansion of urban areas has increased the prevalence of impermeable surfaces, intensifying flooding risks by disrupting natural water infiltration. Permeable pavements have emerged as a sustainable alternative, capable of reducing stormwater runoff, improving surface friction, and mitigating urban heat island effects. Nevertheless, their broader implementation is often hindered by issues such as clogging and limited mechanical strength resulting from high porosity. This study examines the design of interlocking permeable blocks utilizing ultra-high-performance concrete (UHPC) to strike a balance between enhanced drainage capacity and high structural performance. A topology optimization (TO) strategy was applied to numerically model the ideal block geometry, incorporating 105 drainage channels with a diameter of 6 mm—chosen to ensure manufacturability and structural integrity. The UHPC formulation was developed using particle packing optimization with ordinary Portland cement (OPC), silica fume, and limestone filler to reduce binder content while achieving superior strength and workability, guided by rheological assessments. Experimental tests revealed that the perforated UHPC blocks reached compressive strengths of 87.8 MPa at 7 days and 101.0 MPa at 28 days, whereas the solid UHPC blocks achieved compressive strengths of 125.8 MPa and 146.2 MPa, respectively. In contrast, commercial permeable concrete blocks reached only 28.9 MPa at 28 days. Despite a reduction of approximately 30.9% in strength due to perforations, the UHPC-105holes blocks still far exceed the 41 MPa threshold required for certain structural applications. These results highlight the mechanical superiority of the UHPC blocks and confirm their viability for structural use even with enhanced permeability features. The present research emphasizes mechanical and structural performance, while future work will address hydraulic conductivity and anticlogging behavior. Overall, the findings support the use of topology-optimized UHPC permeable blocks as a resilient solution for sustainable urban drainage systems, combining durability, strength, and environmental performance.


  • Open Access

    Functionally graded optimisation of adsorption systems with phase change materials

    by D. S. Prado, R. C. R. Amigo, R. W. Hewson, E. C. N. Silva

    Adsorption phenomena are encountered in several engineering applications. One of its uses is in the storage and transport of gas in the form of adsorption tanks. The exothermic nature of the adsorption process decreases adsorption capacity presenting an impetus to understand the thermal characteristics of the gas storage process. Studies using mixtures of phase change materials and adsorbents in adsorption tanks demonstrate potential improvements in the adsorption capacity of the tanks. They also show that the distribution of phase change materials and adsorbent are important. Thus, this work presents two approaches for optimising the adsorbent domain. The first is to use a semi-analytic model to determine the best homogeneous material concentration for the adsorbent and phase change material for the vessel composition. The other is to use a 2D axisymmetric model to perform FGM optimisation to distribute material in the tank. Results for both models are presented and discussed for different conditions. The study shows that, for the cylindrical geometry, FGM optimisation is always, at least, marginally better than the homogeneous distribution from the semi-analytic model. However, FGM optimisation demands more computing time increases the complexity of implementation and results assembling. The semi-analytic approach is a possible alternative for optimising adsorption systems with phase change material mixed with adsorbents.