Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Sa Zhu has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Fast Driving Cycle Efficiency Optimization of Interior Permanent Magnet Synchronous Machines Considering PWM-Induced Harmonic Losses

    by Runqing Ni, Chengxin Zhong, Sa Zhu

    A multi-objective optimization framework is developed in this work to improve the driving cycle efficiency of IPMSMs, into which a fast-computational approach for PWM-induced harmonic losses is embedded. At a set of characteristic operating points, iron losses are first evaluated under sinusoidal current source (SCS) excitation using Computationally Efficient Finite Element Analysis (CE-FEA), while a Time-Stepping Finite Element Analysis (TS-FEA) spanning one quarter of the electrical period provides the copper losses. For scenarios where the machine is driven by a pulse-width modulation (PWM) voltage source inverter, the harmonic losses arising from modulation are quickly assessed through a small-signal time-harmonic finite element method (THFEA)-based model. The resulting optimization procedure seeks a trade-off between two conflicting goals: minimizing overall losses and reducing material cost. Given an equal cost level, incorporating PWM-related harmonic losses into the design loop cuts down the total loss by 3.11% relative to a baseline that only considers SCS-supply losses. The extra computational burden amounts to 17 h, representing a time rise of roughly 22.65%.

  • White-Box High-Frequency Modeling of Interior Permanent Magnet Synchronous Machines with Hairpin Windings

    by Sa Zhu, Haokun Zhu, Weizhong Fang, Zhaohai Jin

    This paper further details the process of constructing a high-frequency (HF) white-box model for interior permanent magnet synchronous machines (IPMSMs) with hairpin windings based on the small-signal time-harmonic finite element analysis method. The model employs complex differential reluctivity tensors that vary with dc-biased magnetic induction and frequency, enabling accurate simulation of hysteresis, eddy current, and saturation effects in electrical steel sheets. To enhance modeling accuracy, the frequency-dependent resistance and leakage inductance of the end windings are calculated using the three-dimensional finite element method. More importantly, this study combines simulation and experimental methods to conduct a detailed comparative analysis of the influence of impregnation on motor parasitic capacitance and HF impedance characteristics, as well as the impact of rotor presence and position on motor HF impedance characteristics. Experimental results validate that the model established in this paper can accurately predict the differential-mode and common-mode impedance characteristics of IPMSMs with hairpin windings during the design stage.


  • Open Access

    Fast Simulation and Optimization Design of a Slotless Micro-Motor for High-Speed and High-Flow Pumps

    by Zhaohai Jin, Weizhong Fang, Jiawei Xu, Tianxiong Lu, Shitao Yang, Li Zhou, Sa Zhu

    The effective part of the winding in a slotless motor varies across different axial sections of the motor, resulting in a three-dimensional structure. Therefore, it is not feasible to simply use the single-section simulation method of conventional radial field motors for motor simulation. Currently, the simulation of slotless motors primarily depends on three-dimensional electromagnetic fields, which present significant modeling challenges and require extensive simulation times, rendering them unsuitable for engineering applications. This paper introduces a method for analyzing slotless motors using a two-dimensional electromagnetic field, based on the electromagnetic field simulation software EasiMotor (R2025). The study elucidates the principle of employing a two-dimensional electromagnetic field to analyze slotless motors and applies this method to the design of a slotless motor with a diameter of 4.5 mm. Through the fabrication of prototypes and performance testing, experimental results validate the accuracy and efficiency of this method.


  • White-Box High-Frequency Impedance Modeling of Permanent Magnet Synchronous Machines Using Small-Signal Time-Harmonic Finite Element Analysis

    by Sa Zhu, Weizhong Fang, Runqing Ni, Zhaohai Jin, Zhuocheng Lu

    This article advances a two-dimensional (2-D) coupled field-circuit small-signal time-harmonic finite element analysis (THFEA) method for achieving comprehensive modeling of high-frequency (HF) impedances in permanent magnet synchronous machines (PMSMs). The model incorporates a frequency-dependent complex differential reluctivity tensor to simulate the impact of hysteresis, eddy currents, and saturation in electrical steel sheets on self-inductance, mutual inductance, and iron loss resistance of the machines. To efficiently account for eddy current effects without requiring excessive mesh refinement in winding regions, a homogeneous material with equivalent complex permeability is used to replicate the influence of eddy currents on winding resistance and slot leakage inductance. Additionally, a practical approach is proposed to determine this equivalent complex permeability. Subsequently, the 2-D axisymmetric THFEA is then performed to evaluate end leakage inductance and resistance at varying frequencies. Besides, when computing parasitic capacitances, the impact of dielectric loss is considered based on the Debye model. The developed model not only accurately computes the HF impedances of PMSMs but also enables the prediction of overvoltage distribution at arbitrary locations within windings. Experimental validation was conducted on a PMSM with concentrated round-wire windings in the frequency domain and on a stator with distributed hairpin windings in the time domain.


  • Rapid and Accurate Calculation of PWM-Induced Harmonic Currents in IPMSMs Considering Hysteresis and Eddy Current Reaction Effects

    by Sa Zhu, Jianbo Lu, Xin Liang

    This article presents a method based on the small-signal time-harmonic finite element analysis (THFEA) to rapidly and accurately calculate pulsewidth modulation (PWM) induced harmonic currents in interior permanent magnet synchronous machines. Based on the small-signal THFEA, the functional relationships between harmonic voltages and harmonic currents are established, making it possible to rapidly calculate PWM-induced harmonic current spectra with PWM voltage spectra, which lays a solid foundation for achieving the fast and accurate calculation of PWM-induced ac copper losses. More importantly, in order to improve the accuracy of the small-signal model at high frequency, two-dimensional equivalent permanent magnet (PM) conductivity is used to accurately consider the PM eddy current reaction effect at different axial lengths, and a simple method is proposed to modify the differential reluctivity tensor obtained from the single B - H curve for considering the hysteresis and eddy current reaction effects in electrical steel sheets. The proposed method is compared with traditional time-stepping finite element method to demonstrate its merits in calculation speed and accuracy. The comparison of measured and calculated high-frequency impedances and current spectra also approves the accuracy of the proposed method.


  • Fast Driving Cycle Efficiency optimization of an IPMSM with Hairpin Windings Considering PWM-Induced Losses

    by Sa Zhu, Feng Zeng, Jianbo Lu, Ziqing Chu

    This paper proposes a method for the fast driving cycle efficiency optimization of interior permanent magnet synchronous machines (IPMSMs) with hairpin windings, considering pulse-width modulation (PWM) induced harmonic losses. The previously established rapid calculation method of PWM-induced harmonic losses based on the small-signal time-harmonic finite element method is incorporated in the multi-objective optimization process. The paper starts by extracting representative operating points within the cycle period. Subsequently, simplified fast calculation methods for PM losses, iron losses and copper losses under both sinusoidal current source (SCS) supply and PWM voltage source inverter supply are summarized. By doing so, the multi-optimization of the efficiency and cost of IPMSMs considering the automotive driving cycle is achieved. The results indicate that the method considering PWM-induced harmonic losses in multi-objective optimization procedure yields better performance compared to the method considering only losses under SCS supply. Specifically, the total loss is reduced by 3.57% at the same cost, with only 16.5% increase of computational time.


  • Fast Calculation of Electromagnetic Forces in IPMSMs Under PWM VSI Supply Based on Small-Signal Time-Harmonic Finite Element Method

    by Sa Zhu, Jianbo Lu, Feng Zeng

    This paper introduces a novel method for fast calculating the electromagnetic forces in interior permanent magnet synchronous machines (IPMSMs) under pulse width modulation (PWM) voltage source inverter (VSI) supply based on the small-signal time-harmonic finite element analysis (THFEA), which has been successfully utilized for fast calculating the PWM-induced losses in silicon steel sheets and permanent magnets. Based on the small-signal THFEA, the functional relationships between high-frequency harmonic voltages (HFHVs) and corresponding airgap flux densities are established, which are used for calculating the flux density spectra caused by each HFHV in the PWM voltage spectra. Then, the superposition principle is applied for calculating the flux density spectra caused by fundamental currents and all HFHVs, which are converted to the electromagnetic force spectra at last. The relative errors between the force density spectra calculated with the proposed method and those obtained from traditional time-stepping finite element analysis (TSFEA) using PWM voltages as input are within 3.1%, while the proposed method is 24 times faster than the traditional TSFEA.


  • Comparison of Methods Using Different Sources for Computing PWM Effects on Permanent Magnet Machines Considering Eddy Current Reaction

    by S. Zhu, W. Hua, B. Shi

    This article compares two methods for computing high-frequency harmonic currents (HFHCs) and losses in permanent magnet synchronous machines (PMSMs) driven by pulsewidth modulation (PWM) voltage-source inverters (VSIs). The first method uses the currents containing HFHCs, which are obtained from the SIMULINK-based inverter-motor simulation system, as input for time-stepping finite-element analysis (TSFEA) to compute the PWM effects, while the second method directly uses PWM voltage sources as input for conducting the coupled field-circuit TSFEA. It is pointed out that the HFHCs are underestimated with the first method due to neglecting the eddy current reaction effect. Hence, both the iron and permanent magnet losses will be underestimated with the first method. On the contrary, the second method is better for computing the PWM effects because high-frequency harmonic voltages are independent on the eddy current reaction effect under PWM VSI supply and are directly related to high-frequency flux density variations, which determine high-frequency losses. Experiment on an interior PMSM was conducted to validate the simulation in this article.


  • Modeling of PWM-Induced Iron Losses With Frequency-Domain Methods and Low-Frequency Parameters

    by Sa Zhu, Bin Shi

    The high-frequency iron losses caused by sinusoidal flux density variations with frequencies ranging from 2.5 to 40 kHz, amplitudes from 1 to 70 mT, and dc-biased magnetic inductions from 0 to 1.62 T are measured with the dual-transformer system. Then, in this article, a simple frequency-domain model is proposed based on the linear fitting and two-dimensional interpolation methods for engineering applications. In addition, another two frequency-domain models, respectively, considering and neglecting the excess losses are investigated and compared for the high-frequency iron-loss modeling, which only need low-frequency parameters and contain the physical interpretation to the variation of high-frequency iron-loss coefficients with the frequency, ac flux density amplitude, and dc-biased magnetic induction. The iron losses generated by the unipolar and bipolar pulsewidth modulation (PWM) voltages with different switching frequencies and modulation factors are measured to testify the three models. It is shown that the three models in this article are more accurate than the previously proposed one for calculating the PWM-induced iron loss by considering the variation of model parameters with the dc-biased magnetic induction and ac flux density amplitude, especially when silicon steel sheets reach the saturation.