John M. Lang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
John M. Lang has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Dana Mcgraw Dattelbaum
Los Alamos National Laboratory
3 shared publications - Joshua Damon Coe
Los Alamos National Laboratory (LANL), Los Alamos, NM (United States)
2 shared publications - Peter M. Goodwin
Los Alamos National Lab. (United States)
2 shared publications Adam H. Pacheco
Los Alamos National Laboratory, Los Alamos New Mexico USA 87545
1 shared publicationBruce R. Marshall
NSTec Special Technologies Laboratory, Santa Barbara CA 93111 USA
1 shared publicationD. Anthony Fredenburg
Los Alamos National Laboratory, Los Alamos, NM, USA
1 shared publication
Latest Publications
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2844 (1)
Improving manganin gauge measurements near radiographic fiducials
In dynamic experiments diagnosed with radiography and stress gauges, the gauges are often placed adjacent to radio-graphic fiducials, such as Ta foil, which perturbs the stress measurement. We conducted experiments to test the performance of different arrangements of manganin stress gauges and Ta foils. Three different gauge/foil configurations were tested, as well as a solitary gauge as control. Gauge/foil layers were placed between high-density polyethylene (HDPE) discs and impacted by a projectile in a gas gun, a simplification of a dynamic, high explosive experiment configuration. The stress measurements were minimally perturbed when a section of foil was removed near the active element of the gauge, as expected. A follow-up experiment showed that the modification to the foil has minimal impact on the radiographic measurement of the dynamic flow.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2844 (1)
Improving manganin gauge measurements near radiographic fiducials
In dynamic experiments diagnosed with radiography and stress gauges, the gauges are often placed adjacent to radio-graphic fiducials, such as Ta foil, which perturbs the stress measurement. We conducted experiments to test the performance of different arrangements of manganin stress gauges and Ta foils. Three different gauge/foil configurations were tested, as well as a solitary gauge as control. Gauge/foil layers were placed between high-density polyethylene (HDPE) discs and impacted by a projectile in a gas gun, a simplification of a dynamic, high explosive experiment configuration. The stress measurements were minimally perturbed when a section of foil was removed near the active element of the gauge, as expected. A follow-up experiment showed that the modification to the foil has minimal impact on the radiographic measurement of the dynamic flow.
- 3 July 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1979 (1) , 090009
Equations of state and shock-driven chemistry in poly(dimethylsiloxane)-based foams
Modeling the silicone-based polymer SX358 with two equations of state, one of the unreacted material and another for the decomposition products, captures the experimental shock and thermal data quite well for full density and porous material. By utilizing improved physics models that take into account the macromolecular nature of polymers we are able to capture experimental thermal data. The behavior of SX358 under shock compression is consistent with other polymers in that the threshold for reaction decreases with increasing porosity and chemical decomposition of foams causes a volume expansion, whereas we see a volume collapse in reacted full density SX358.
- 3 July 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1979 (1) , 090009
Equations of state and shock-driven chemistry in poly(dimethylsiloxane)-based foams
Modeling the silicone-based polymer SX358 with two equations of state, one of the unreacted material and another for the decomposition products, captures the experimental shock and thermal data quite well for full density and porous material. By utilizing improved physics models that take into account the macromolecular nature of polymers we are able to capture experimental thermal data. The behavior of SX358 under shock compression is consistent with other polymers in that the threshold for reaction decreases with increasing porosity and chemical decomposition of foams causes a volume expansion, whereas we see a volume collapse in reacted full density SX358.
- 3 July 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1979 (1) , 100013
Shock-driven reactions in acrylonitrile
Shock-driven reactions in simple molecules often occur with densification along the reaction coordinate. Acrylonitrile (CH2CHCN) is a simple molecule that undergoes shock-driven reaction on the principal Hugoniot. Using in-situ embedded electromagnetic gauging techniques and the LANL large bore two-stage gas gun, multi-wave structures were observed in acrylonitrile indicating the formation of higher density shock-induced reaction intermediates and products. Using the data from the embedded gauge experiments, time-resolved Raman spectroscopy experiments were conducted to elucidate reaction species in shocked acrylonitrile, but it was found that the conditions became optically opaque even during the first wave at modest input conditions. A description of the time-resolved Raman system coupled to the LANL large-bore two-stage light gas gun is also provided.
- 3 July 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1979 (1) , 100013
Shock-driven reactions in acrylonitrile
Shock-driven reactions in simple molecules often occur with densification along the reaction coordinate. Acrylonitrile (CH2CHCN) is a simple molecule that undergoes shock-driven reaction on the principal Hugoniot. Using in-situ embedded electromagnetic gauging techniques and the LANL large bore two-stage gas gun, multi-wave structures were observed in acrylonitrile indicating the formation of higher density shock-induced reaction intermediates and products. Using the data from the embedded gauge experiments, time-resolved Raman spectroscopy experiments were conducted to elucidate reaction species in shocked acrylonitrile, but it was found that the conditions became optically opaque even during the first wave at modest input conditions. A description of the time-resolved Raman system coupled to the LANL large-bore two-stage light gas gun is also provided.
- 3 July 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1979 (1) , 090008
Deep-release of Epon 828 epoxy from the shock-driven reaction product phase
A series of gas-gun experiments was conducted to obtain product isentropes for 70/30 weight percent Epon 828 epoxy resin/Jeffamine T-403 curing agent. Thin epoxy flyers backed by a low-density syntactic foam impacted lithium fluoride (LiF) windows at velocities up to 6.3 km/s, creating stresses in excess of those required for reaction (∼25 GPa). Following this, a rarefaction fan from the back of the thin flyer reduced the pressure in the epoxy products. VISAR and PDV were used to measure the velocity of the epoxy/LiF interface. Numerical simulations using several different treatments for the reactant-to-product transformation were conducted and the results compared with measured wave profiles. The best agreement with experiment was obtained using separate tabular equations of state for the reactants and products and an irreversible transformation to products.
- 3 July 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1979 (1) , 090008
Deep-release of Epon 828 epoxy from the shock-driven reaction product phase
A series of gas-gun experiments was conducted to obtain product isentropes for 70/30 weight percent Epon 828 epoxy resin/Jeffamine T-403 curing agent. Thin epoxy flyers backed by a low-density syntactic foam impacted lithium fluoride (LiF) windows at velocities up to 6.3 km/s, creating stresses in excess of those required for reaction (∼25 GPa). Following this, a rarefaction fan from the back of the thin flyer reduced the pressure in the epoxy products. VISAR and PDV were used to measure the velocity of the epoxy/LiF interface. Numerical simulations using several different treatments for the reactant-to-product transformation were conducted and the results compared with measured wave profiles. The best agreement with experiment was obtained using separate tabular equations of state for the reactants and products and an irreversible transformation to products.
- 13 January 2017
- Published by AIP Publishing
- Vol. 1793 (1) , 160008
Fiber-interferometric detection of gun-launched projectiles
We are developing a new diagnostic useful for the non-invasive detection of projectile passage in the launch tube of a gas gun. The sensing element consists of one or more turns of single-mode optical fiber that is epoxy-bonded around the external circumference of the launch tube. The hoop strain induced in the launch tube by the passage of the projectile causes a momentary expansion of the fiber loop. This transient change in path length is detected with high sensitivity using a fiber optic-based interferometer developed by the NSTec Special Technologies Laboratory. We have fielded this new diagnostic, along with fiber optic Bragg grating (FBG) strain gauges we previously used for this purpose, on a variety of gas guns used for shock compression studies at Los Alamos and Sandia National Laboratories. We anticipate that, when coupled with a broad-range analog demodulator circuit, the fiber optic interferometer will have improved dynamic range over that of the FBG strain gauge approach. Moreover, in contrast to the FBG strain gauge which is somewhat temperature sensitive, the interferometric approach requires no alignment immediately prior to the experiment and is therefore easier to implement. Both approaches provide early, pre-event signals useful for triggering high-latency diagnostics.
- 13 January 2017
- Published by AIP Publishing
- Vol. 1793 (1) , 160008
Fiber-interferometric detection of gun-launched projectiles
We are developing a new diagnostic useful for the non-invasive detection of projectile passage in the launch tube of a gas gun. The sensing element consists of one or more turns of single-mode optical fiber that is epoxy-bonded around the external circumference of the launch tube. The hoop strain induced in the launch tube by the passage of the projectile causes a momentary expansion of the fiber loop. This transient change in path length is detected with high sensitivity using a fiber optic-based interferometer developed by the NSTec Special Technologies Laboratory. We have fielded this new diagnostic, along with fiber optic Bragg grating (FBG) strain gauges we previously used for this purpose, on a variety of gas guns used for shock compression studies at Los Alamos and Sandia National Laboratories. We anticipate that, when coupled with a broad-range analog demodulator circuit, the fiber optic interferometer will have improved dynamic range over that of the FBG strain gauge approach. Moreover, in contrast to the FBG strain gauge which is somewhat temperature sensitive, the interferometric approach requires no alignment immediately prior to the experiment and is therefore easier to implement. Both approaches provide early, pre-event signals useful for triggering high-latency diagnostics.