Marek Sebik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Marek Sebik has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Barbora Hajkova
Department of Anatomy and Biomechanics, Charles University, 162 52 Prague, Czech Republic
1 shared publication - Dita Hylmarova
Department of Anatomy and Biomechanics, Charles University, 162 52 Prague, Czech Republic
1 shared publication - František Lopot
Department of Designing and Machine Components, Faculty of Mechanical Engineering, Czech Technical University in Prague, Technická 4, Prague 6, 160 00 Dejvice, Czech Republic
1 shared publication - František Maršík
Department of Anatomy and Biomechanics, Charles University, 162 52 Prague, Czech Republic
1 shared publication - Karel Jelen
Department of Anatomy and Biomechanics, Charles University, 162 52 Prague, Czech Republic
1 shared publication M. Chadima
1 shared publication
Latest Publications
- Open Access
Pedestrian Safety in Frontal Tram Collision, Part 2: Laminated Glass as a Crucial Part of the Absorption and Deformation Zone—Its Impact Test and Analysis
As was shown in the previous part of the study, windshields are an important part of the passive safety means of modern low-floor trams with an extraordinary effect on pedestrian safety in a pedestrian–tram collisions. Therefore, maximum attention must be paid to the definition of tram windshield characteristics. This article describes a windshield crash test, from which data are obtained to verify the feasibility of the applied computational approaches. A developed analytical model is utilised for a simple description of the energy balance during collision with an illustrative definition of the important parameters of laminated glass as well as their clear physical interpretations. The finite element analysis (FEA) performed in Ansys software using two versions of material definition, namely a simpler (*MAT_ELASTIC with nonlocal failure criterion) and a more complex (*MAT_GLASS with brittle stress-state-dependent failure) material model, which are presented as suitable for obtaining a detailed description of the shattering process of laminated glass, which can also be used effectively in windshield engineering.
Open AccessPedestrian Safety in Frontal Tram Collision, Part 2: Laminated Glass as a Crucial Part of the Absorption and Deformation Zone—Its Impact Test and Analysis
As was shown in the previous part of the study, windshields are an important part of the passive safety means of modern low-floor trams with an extraordinary effect on pedestrian safety in a pedestrian–tram collisions. Therefore, maximum attention must be paid to the definition of tram windshield characteristics. This article describes a windshield crash test, from which data are obtained to verify the feasibility of the applied computational approaches. A developed analytical model is utilised for a simple description of the energy balance during collision with an illustrative definition of the important parameters of laminated glass as well as their clear physical interpretations. The finite element analysis (FEA) performed in Ansys software using two versions of material definition, namely a simpler (*MAT_ELASTIC with nonlocal failure criterion) and a more complex (*MAT_GLASS with brittle stress-state-dependent failure) material model, which are presented as suitable for obtaining a detailed description of the shattering process of laminated glass, which can also be used effectively in windshield engineering.
- 10 July 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1978 (1) , 470046
Dynamic behavior of cement-bonded wood-chip board
The cement-bonded wood-chip material is used in many civil applications as building material or noise protecting material. This investigation is a part of complex development of safety road barrier with integrated noise protecting wall. Any kind of this application has to comply withstrict conditions defined in national standards for safety on roads. Usually those standards prescribe very expensive crash tests. This development process can be supported with numerical simulation but detailed knowledge about material properties and behavior is necessary as an essential input. The cement-bonded wood-chip material properties were analyzed in this work. Set of real quasi-static and dynamic experiments was performed. The material model, created based on the obtained results, will be used in numerical simulation of crash test of mobile noise protection wall according EN1317.
- 10 July 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1978 (1) , 470046
Dynamic behavior of cement-bonded wood-chip board
The cement-bonded wood-chip material is used in many civil applications as building material or noise protecting material. This investigation is a part of complex development of safety road barrier with integrated noise protecting wall. Any kind of this application has to comply withstrict conditions defined in national standards for safety on roads. Usually those standards prescribe very expensive crash tests. This development process can be supported with numerical simulation but detailed knowledge about material properties and behavior is necessary as an essential input. The cement-bonded wood-chip material properties were analyzed in this work. Set of real quasi-static and dynamic experiments was performed. The material model, created based on the obtained results, will be used in numerical simulation of crash test of mobile noise protection wall according EN1317.