Johnny Qin
Johnny Qin has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
Shuangshuang Yu
4 shared publicationsYanmei Meng
4 shared publicationsJianfan Wu
College of Mechanical Engineering Guangxi University Nanning China
3 shared publicationsTao Yao
College of Mechanical Engineering Guangxi University Nanning China
3 shared publications- Yanmei Meng
School of Mechanical Engineering, Guangxi University, Nanning 530004, China
3 shared publications - Baotang Shen
CSIRO Mineral Resources
2 shared publications
Latest Publications
- Open Access
- 1 January 2025
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Podzemni radovi
- No. 46,p. 1-15
Interpretation of transient caving dust patterns during sequential caving operation in LTCC face
Longwall top coal caving (LTCC) is a mining technology introduced for enhancing the coal production rate by using the top coal caving (TCC) operations for thick seams. LTCC mine increases coal production rates but at the expense of high dust exposure and may create hazardous conditions for mine operators. It is vital for the introduction of advanced dust control technologies as well as strategies during LTCC operations for dust reduction. For developing LTCC dust control strategies, fundamental understanding of transient caving dust flow pattern across the face is necessary. Note, region above the rear armored face conveyor (AFC) is difficult to access for carrying out field measurements and hence numerical approach is the only option left for determining the dust and flow fields. In this paper, an attempt is made to predict respirable dust flow patterns during sequential caving operations in the mid face region using computational fluid dynamics (CFD) techniques. Results predicted caving dust sources entering the downstream chock and dispersing into the walkway region within 5 seconds. Respirable dust in the first downstream walkway remains below 2mg/m³ whereas in the second downstream chock in the sequence is above 2.5mg/m³. Interpreting the results, it can be inferred that caving dust controls using water sprays need to be activated in not only in the caving chock but also in the immediate downstream chock from the start of the sequence caving for preventing the migration respirable dust into the walkway regions of the downstream chocks until the completion of the sequential caving operation in all the five chocks.
- 1 January 2025
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Podzemni radovi
- No. 46,p. 1-15
Open AccessInterpretation of transient caving dust patterns during sequential caving operation in LTCC face
Longwall top coal caving (LTCC) is a mining technology introduced for enhancing the coal production rate by using the top coal caving (TCC) operations for thick seams. LTCC mine increases coal production rates but at the expense of high dust exposure and may create hazardous conditions for mine operators. It is vital for the introduction of advanced dust control technologies as well as strategies during LTCC operations for dust reduction. For developing LTCC dust control strategies, fundamental understanding of transient caving dust flow pattern across the face is necessary. Note, region above the rear armored face conveyor (AFC) is difficult to access for carrying out field measurements and hence numerical approach is the only option left for determining the dust and flow fields. In this paper, an attempt is made to predict respirable dust flow patterns during sequential caving operations in the mid face region using computational fluid dynamics (CFD) techniques. Results predicted caving dust sources entering the downstream chock and dispersing into the walkway region within 5 seconds. Respirable dust in the first downstream walkway remains below 2mg/m³ whereas in the second downstream chock in the sequence is above 2.5mg/m³. Interpreting the results, it can be inferred that caving dust controls using water sprays need to be activated in not only in the caving chock but also in the immediate downstream chock from the start of the sequence caving for preventing the migration respirable dust into the walkway regions of the downstream chocks until the completion of the sequential caving operation in all the five chocks.
- Open Access
Rock Mass and Pore Fluid Response in Deep Mining: A Field Monitoring Study at Inclined Longwalls
The dynamics of stress, deformation and pore pressure in the surrounding strata of underground mines are of fundamental importance to groundwater and gas emission management. Compared to numerous studies on the overlying strata, there are significantly fewer investigations concerning the underlying strata, particularly involving large-scale field monitoring. This paper presents a comprehensive field monitoring study conducted at two longwall panels with a depth of around 800 m and an inclination angle of 21°. The monitoring program focused on the floor strata within 50 m below the mining operation, but also covered the roof strata close to the longwall roadway. The purpose was to characterise the favourable zone for gas extraction from the floor coal seams. A combination of stressmeters, extensometers and piezometers were deployed and installed underground. The monitored results demonstrated that the stress change exhibited a three-stage variation—increase, decrease and recovery—during which the strata deformed and the pore pressure changed correspondingly. Strata expansion in the floor occurred primarily in the region 0–35 m behind the longwall face and vertically to at least 42 m below. Some predictive methods of the depth of the failure zone used in shallow mines were analysed to determine if they were still applicable for mining at a depth of around 800 m.
Open AccessRock Mass and Pore Fluid Response in Deep Mining: A Field Monitoring Study at Inclined Longwalls
The dynamics of stress, deformation and pore pressure in the surrounding strata of underground mines are of fundamental importance to groundwater and gas emission management. Compared to numerous studies on the overlying strata, there are significantly fewer investigations concerning the underlying strata, particularly involving large-scale field monitoring. This paper presents a comprehensive field monitoring study conducted at two longwall panels with a depth of around 800 m and an inclination angle of 21°. The monitoring program focused on the floor strata within 50 m below the mining operation, but also covered the roof strata close to the longwall roadway. The purpose was to characterise the favourable zone for gas extraction from the floor coal seams. A combination of stressmeters, extensometers and piezometers were deployed and installed underground. The monitored results demonstrated that the stress change exhibited a three-stage variation—increase, decrease and recovery—during which the strata deformed and the pore pressure changed correspondingly. Strata expansion in the floor occurred primarily in the region 0–35 m behind the longwall face and vertically to at least 42 m below. Some predictive methods of the depth of the failure zone used in shallow mines were analysed to determine if they were still applicable for mining at a depth of around 800 m.
- 14 February 2021
- Published by Hindawi Limited in Journal of Food Processing and Preservation
- Vol. 45 (4) , e15365
Multi‐objective optimization of cane sugar continuous crystallization system design based on computational fluid dynamics
This work focused on improving circulation and mixing of the massecuite and reducing the energy loss in the cane sugar continuous crystallization system. The developed Computational Fluid Dynamics (CFD) model is based on the continuous crystallization system of a sugarcane mill in Guangxi, China and verified with the actual operation data. The calculated entropy production and pressure drop of the system are used as indices for assessing the performance of the system. Next, 350 CFD simulations are conducted in the parametric experiment platform with 9 parameters and produces a collection of data. Then based on the CFD dataset, the data‐driven model is employed for regression of the relations between key parameters and indices. The implemented data‐driven model is used for Non‐dominated Sorting Genetic Algorithm (NSGA‐II) to obtain the optimal result of Pareto frontier. CFD simulation with the optimized parameters reduces entropy by 9.76% and reduces pressure drop by 11.52%.
- 14 February 2021
- Published by Hindawi Limited in Journal of Food Processing and Preservation
- Vol. 45 (4) , e15365
Multi‐objective optimization of cane sugar continuous crystallization system design based on computational fluid dynamics
This work focused on improving circulation and mixing of the massecuite and reducing the energy loss in the cane sugar continuous crystallization system. The developed Computational Fluid Dynamics (CFD) model is based on the continuous crystallization system of a sugarcane mill in Guangxi, China and verified with the actual operation data. The calculated entropy production and pressure drop of the system are used as indices for assessing the performance of the system. Next, 350 CFD simulations are conducted in the parametric experiment platform with 9 parameters and produces a collection of data. Then based on the CFD dataset, the data‐driven model is employed for regression of the relations between key parameters and indices. The implemented data‐driven model is used for Non‐dominated Sorting Genetic Algorithm (NSGA‐II) to obtain the optimal result of Pareto frontier. CFD simulation with the optimized parameters reduces entropy by 9.76% and reduces pressure drop by 11.52%.
- 1 February 2021
- Published by Elsevier in Journal of Food Engineering
- Vol. 291
Modeling and optimization of sugarcane juice clarification process
- 1 February 2021
- Published by Elsevier in Journal of Food Engineering
- Vol. 291
Modeling and optimization of sugarcane juice clarification process
- Open Access
- 23 January 2021
- Published by Hindawi Limited in Mathematical Problems in Engineering
- Vol. 2021, 1-13
Research on Torsional Property of Body-In-White Based on Square Box Model and Multiobjective Genetic Algorithm
In order to assess the performance of a vehicle in the conceptual design stage, a square box model was proposed to predict the torsional stiffness and the first-order torsional frequency of Body-in-White. The structure of Body-in-White was decomposed into eight simple structural surfaces, from which a square box model was constructed. Based on the finite element method, modified shear stiffness of each simple structure surface was calculated and the torsional stiffness was obtained. Then, simple structural surfaces of Body-in-White were constructed into an eight degree-of-freedom series spring system to calculate the first-order torsional frequency. Furthermore, a multiobjective genetic algorithm was used to determine the thickness and structural reinforcement of panels with small stiffness, so as to achieve the goal of increasing the stiffness while reducing the mass of the panel. The result shows that the optimal values of thickness are reduced by around 9.9 percent without affecting their performance by the proposed method. Compared to the prediction results obtained with the complicated numerical simulation, the relative error of the square box model in predicting the torsional stiffness is 6.04 percent and in predicting the first-order torsional frequency is 0.95 percent, indicating that the prediction model is effective.
- 23 January 2021
- Published by Hindawi Limited in Mathematical Problems in Engineering
- Vol. 2021, 1-13
Open AccessResearch on Torsional Property of Body-In-White Based on Square Box Model and Multiobjective Genetic Algorithm
In order to assess the performance of a vehicle in the conceptual design stage, a square box model was proposed to predict the torsional stiffness and the first-order torsional frequency of Body-in-White. The structure of Body-in-White was decomposed into eight simple structural surfaces, from which a square box model was constructed. Based on the finite element method, modified shear stiffness of each simple structure surface was calculated and the torsional stiffness was obtained. Then, simple structural surfaces of Body-in-White were constructed into an eight degree-of-freedom series spring system to calculate the first-order torsional frequency. Furthermore, a multiobjective genetic algorithm was used to determine the thickness and structural reinforcement of panels with small stiffness, so as to achieve the goal of increasing the stiffness while reducing the mass of the panel. The result shows that the optimal values of thickness are reduced by around 9.9 percent without affecting their performance by the proposed method. Compared to the prediction results obtained with the complicated numerical simulation, the relative error of the square box model in predicting the torsional stiffness is 6.04 percent and in predicting the first-order torsional frequency is 0.95 percent, indicating that the prediction model is effective.
- 1 September 2020
- Published by Elsevier in Journal of Food Engineering
- Vol. 280
Monitoring sugar crystallization with deep neural networks
- 1 September 2020
- Published by Elsevier in Journal of Food Engineering
- Vol. 280
Monitoring sugar crystallization with deep neural networks
- Open Access
Preliminary Investigation into Measurement While Drilling as a Means to Characterize the Coalmine Roof
The variable nature of the coalmine roof poses a challenge to roadway stability during underground coal mining. There have been fatalities and financial losses in the coal mining industry due to roadway failures and roof falls. Generally, the geotechnical and geological data gathered from exploration boreholes, which are drilled at considerable distances from each other, are used to characterize the thickness and quality (including strength) of the coalmine roof. This process provides a limited number of samples that cannot represent the discontinuous nature of the strata in the coalmine roof nor can they form reliable inputs to a digital model of the rock mass component of the digital mine. Gaining confidence in the strata properties of the coalmine roof is necessary for the modelling, design, and maintenance of roadways. The paper describes the progress of the ongoing work to investigate the monitoring while drilling (MWD) concept for characterizing coalmine roofs. Large-scale drilling experiments in synthesized sandwiched rock samples without interfaces were carried out. The drilling response data were analyzed to identify whether the drill data differentiates the various strengths associated with the rock samples. The initial results show that the drilling data can differentiate the synthesized rock samples.
Open AccessPreliminary Investigation into Measurement While Drilling as a Means to Characterize the Coalmine Roof
The variable nature of the coalmine roof poses a challenge to roadway stability during underground coal mining. There have been fatalities and financial losses in the coal mining industry due to roadway failures and roof falls. Generally, the geotechnical and geological data gathered from exploration boreholes, which are drilled at considerable distances from each other, are used to characterize the thickness and quality (including strength) of the coalmine roof. This process provides a limited number of samples that cannot represent the discontinuous nature of the strata in the coalmine roof nor can they form reliable inputs to a digital model of the rock mass component of the digital mine. Gaining confidence in the strata properties of the coalmine roof is necessary for the modelling, design, and maintenance of roadways. The paper describes the progress of the ongoing work to investigate the monitoring while drilling (MWD) concept for characterizing coalmine roofs. Large-scale drilling experiments in synthesized sandwiched rock samples without interfaces were carried out. The drilling response data were analyzed to identify whether the drill data differentiates the various strengths associated with the rock samples. The initial results show that the drilling data can differentiate the synthesized rock samples.
- Open Access
- 23 September 2019
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 11 (9)
Research on innovative design of a new rope knotter
Aiming at the complex structure and high manufacturing process requirements of traditional knotter, this article proposes a new rope knotting method. Based on the knotting method, a knotter is designed to use a new mechanism which is made up of two new incomplete gear mechanisms to drive rope clamping mechanism and rope hooking and griping mechanism. First, a kinematic cycle diagram of the knotter is determined, and the structures of each key mechanism are designed. Then, a virtual prototype of the knotter is established by Unigraphics and imported into Automated Dynamic Analysis of Mechanical Systems to analyze the kinematic of each key mechanism. The success rate is 98.4% through 500 physical tests on the physical model of the knotter. The results indicate that the knotting method is reliable. The knotter can meet the requirements of structure, posture, and coordination during knotting process. The new knotter has no separate mechanism for cutting rope and tripping out of the rope buckle. Therefore, the structure is simplified and reduces the design and manufacturing difficulties. Furthermore, the new incomplete gear mechanism solves the problem that in the conventional incomplete gear mechanism, the driven gear can swing at a large angle or even cannot be locked in the case when the locking arc of the passive gear is too short.
- 23 September 2019
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 11 (9)
Open AccessResearch on innovative design of a new rope knotter
Aiming at the complex structure and high manufacturing process requirements of traditional knotter, this article proposes a new rope knotting method. Based on the knotting method, a knotter is designed to use a new mechanism which is made up of two new incomplete gear mechanisms to drive rope clamping mechanism and rope hooking and griping mechanism. First, a kinematic cycle diagram of the knotter is determined, and the structures of each key mechanism are designed. Then, a virtual prototype of the knotter is established by Unigraphics and imported into Automated Dynamic Analysis of Mechanical Systems to analyze the kinematic of each key mechanism. The success rate is 98.4% through 500 physical tests on the physical model of the knotter. The results indicate that the knotting method is reliable. The knotter can meet the requirements of structure, posture, and coordination during knotting process. The new knotter has no separate mechanism for cutting rope and tripping out of the rope buckle. Therefore, the structure is simplified and reduces the design and manufacturing difficulties. Furthermore, the new incomplete gear mechanism solves the problem that in the conventional incomplete gear mechanism, the driven gear can swing at a large angle or even cannot be locked in the case when the locking arc of the passive gear is too short.
- Open Access
- 9 April 2019
- Published by Wiley in Food Science & Nutrition
- Vol. 7 (5) , 1606-1614
Data‐driven modeling based on kernel extreme learning machine for sugarcane juice clarification
Clarification of sugarcane juice is an important operation in the production process of sugar industry. The gravity purity and the color value of juice are the two most important evaluation indexes in the cane sugar production using the sulphitation clarification method. However, in the actual operation, the measurement of these two indexes is usually obtained by offline experimental titration, which makes it impossible to timely adjust the system indicators. A data‐driven modeling based on kernel extreme learning machine is proposed to predict the gravity purity of juice and the color value of clear juice. The model parameters are optimized by particle swarm optimization. Experiments are conducted to verify the effectiveness and superiority of the modeling method. Compared with BP neural network, radial basis neural network, and support vector machine, the model has a good performance, which proves the reliability of the model.
- 9 April 2019
- Published by Wiley in Food Science & Nutrition
- Vol. 7 (5) , 1606-1614
Open AccessData‐driven modeling based on kernel extreme learning machine for sugarcane juice clarification
Clarification of sugarcane juice is an important operation in the production process of sugar industry. The gravity purity and the color value of juice are the two most important evaluation indexes in the cane sugar production using the sulphitation clarification method. However, in the actual operation, the measurement of these two indexes is usually obtained by offline experimental titration, which makes it impossible to timely adjust the system indicators. A data‐driven modeling based on kernel extreme learning machine is proposed to predict the gravity purity of juice and the color value of clear juice. The model parameters are optimized by particle swarm optimization. Experiments are conducted to verify the effectiveness and superiority of the modeling method. Compared with BP neural network, radial basis neural network, and support vector machine, the model has a good performance, which proves the reliability of the model.
- 1 January 2019
- Published by Elsevier in Journal of Food Engineering
- Vol. 241, 159-165
Data-driven soft sensor modeling based on twin support vector regression for cane sugar crystallization
- 1 January 2019
- Published by Elsevier in Journal of Food Engineering
- Vol. 241, 159-165
Data-driven soft sensor modeling based on twin support vector regression for cane sugar crystallization