Morteza Saghafi Yazdi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Morteza Saghafi Yazdi has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Morteza Taheri
Department of Advanced Materials and New Technologies, Iranian Research Organization for Science and Technology (IROST), Tehran, Iran
3 shared publications Amirhossein Moghanian
Department of Materials Engineering, Imam Khomeini International University, Qazvin, Iran
2 shared publicationsSh. Mohajerzadeh
University of Tehran
2 shared publicationsSh. Zangeneh
Razi University
2 shared publicationsA. H. Moghanian
Imam Khomeini International University
1 shared publicationA. Yousefifar
Department of Materials Science and Engineering Faculty of Engineering Imam Khomeini International University P.O. Box 15875-4413 Qazvin Iran
1 shared publication
Latest Publications
- 11 November 2026
- Published by Springer Nature in Emergent Materials
- Vol. 9 (11) , 283
Ultrasonic-assisted laser cladding of NiCrCoMnFe high-entropy alloy coatings on GTD-111 superalloy: microstructural evolution and tribological performance
- 11 November 2026
- Published by Springer Nature in Emergent Materials
- Vol. 9 (11) , 283
Ultrasonic-assisted laser cladding of NiCrCoMnFe high-entropy alloy coatings on GTD-111 superalloy: microstructural evolution and tribological performance
- 1 October 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (10) , 105954
Investigation of the effect of laser surface treatment on the hot corrosion properties of CSZ/YSZ multilayer TBC coatings
The purpose of the present work is to systematically investigate how laser surface treatment can enhance the ability of advanced thermal barrier coating systems to protect gas turbine substrate materials, focusing on improved phase stability and resistance to hot corrosion through optimized multilayer architectures. Through comprehensive characterization via XRD, SEM, and EDS analyses, we demonstrated that laser treatment markedly enhances coating performance by reducing the monoclinic ZrO 2 phase content by approximately 40%, as a result of rapid solidification (∼10 7 °C s −1 ) and microstructural refinement. The optimized MCrAlY-CSZ-YSZ system with laser modification exhibited superior hot corrosion resistance, enduring 6 cycles compared to only 4 cycles for conventional coatings, attributed to densification (4 formation and improving thermal expansion matching. These findings establish laser surface engineering as an effective approach for simultaneously enhancing phase stability and corrosion resistance in TBCs, offering practical solutions for extending turbine component durability in high-temperature corrosive environments. The results provide valuable insights for developing next-generation protective coatings with improved performance characteristics. Thus, the tailored multilayer TBC developed in this study, especially with the inclusion of the CSZ interlayer and laser surface modification, offers superior adhesion, reduced corrosive penetration, and optimized thermal compatibility with the turbine substrate, making it highly suitable for extending the service life of gas turbine components under aggressive operating conditions.
- 1 October 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (10) , 105954
Investigation of the effect of laser surface treatment on the hot corrosion properties of CSZ/YSZ multilayer TBC coatings
The purpose of the present work is to systematically investigate how laser surface treatment can enhance the ability of advanced thermal barrier coating systems to protect gas turbine substrate materials, focusing on improved phase stability and resistance to hot corrosion through optimized multilayer architectures. Through comprehensive characterization via XRD, SEM, and EDS analyses, we demonstrated that laser treatment markedly enhances coating performance by reducing the monoclinic ZrO 2 phase content by approximately 40%, as a result of rapid solidification (∼10 7 °C s −1 ) and microstructural refinement. The optimized MCrAlY-CSZ-YSZ system with laser modification exhibited superior hot corrosion resistance, enduring 6 cycles compared to only 4 cycles for conventional coatings, attributed to densification (4 formation and improving thermal expansion matching. These findings establish laser surface engineering as an effective approach for simultaneously enhancing phase stability and corrosion resistance in TBCs, offering practical solutions for extending turbine component durability in high-temperature corrosive environments. The results provide valuable insights for developing next-generation protective coatings with improved performance characteristics. Thus, the tailored multilayer TBC developed in this study, especially with the inclusion of the CSZ interlayer and laser surface modification, offers superior adhesion, reduced corrosive penetration, and optimized thermal compatibility with the turbine substrate, making it highly suitable for extending the service life of gas turbine components under aggressive operating conditions.
- 11 October 2024
- Published by Springer Nature in Emergent Materials
- Vol. 8 (1) , 887-904
Investigation of tribological behavior for IN625 coating on IN738 superalloy by laser cladding process
- 11 October 2024
- Published by Springer Nature in Emergent Materials
- Vol. 8 (1) , 887-904
Investigation of tribological behavior for IN625 coating on IN738 superalloy by laser cladding process
- Open Access
ElectroCatalytic Activity of Nickel Foam with Co, Mo, and Ni Phosphide Nanostructures
In this study, the electrocatalytic activity of nickel foam, which is activated by cobalt, molybdenum, and nickel phosphide nanostructures, is prepared by the plasma hydrothermal method for use in the release of hydrogen and oxygen. The morphology and crystallographic structure of the synthesized phosphide specimens were examined by means of scanning electron microscopy, Fourier-transform infrared spectroscopy, and X-ray diffraction. Moreover, the electrolysis activity for these sets of specimens was investigated using the Tafel polarization curve or linear sweep voltammetry, cyclic voltammetry, as well as by means of the electrochemical impedance spectroscopy technique. Preliminary results show that nickel phosphide presents the highest electrocatalytic activity than the other phosphides developed in this research. In this regard, it presents an electrocatalytic activity to release hydrogen and oxygen of around −1.7 and 0.82 mV, which is measured at a current density of 100 mA·cm−2, respectively.
Open AccessElectroCatalytic Activity of Nickel Foam with Co, Mo, and Ni Phosphide Nanostructures
In this study, the electrocatalytic activity of nickel foam, which is activated by cobalt, molybdenum, and nickel phosphide nanostructures, is prepared by the plasma hydrothermal method for use in the release of hydrogen and oxygen. The morphology and crystallographic structure of the synthesized phosphide specimens were examined by means of scanning electron microscopy, Fourier-transform infrared spectroscopy, and X-ray diffraction. Moreover, the electrolysis activity for these sets of specimens was investigated using the Tafel polarization curve or linear sweep voltammetry, cyclic voltammetry, as well as by means of the electrochemical impedance spectroscopy technique. Preliminary results show that nickel phosphide presents the highest electrocatalytic activity than the other phosphides developed in this research. In this regard, it presents an electrocatalytic activity to release hydrogen and oxygen of around −1.7 and 0.82 mV, which is measured at a current density of 100 mA·cm−2, respectively.
- 28 June 2021
- Published by Springer Nature in Ionics
- Vol. 27 (9) , 3777-3791
Mixed ternary metal MFeCo (M = Al, Mg, Cu, Zn, or Ni) oxide electrodes for high-performance energy storage devices
- 28 June 2021
- Published by Springer Nature in Ionics
- Vol. 27 (9) , 3777-3791
Mixed ternary metal MFeCo (M = Al, Mg, Cu, Zn, or Ni) oxide electrodes for high-performance energy storage devices
- 1 December 2020
- Published by Wiley in ChemistrySelect
- Vol. 5 (45) , 14282-14287
Synthesis, Characterization and Investigation of Hydrogen Evolution Activity of Ni‐Mo/Al 2 O 3 Composite
In the present study, the hydrogen evolution activity of the Ni−Mo/Al 2 O 3 catalyst was investigated. This catalyst was produced by milling of oxide precursors of nickel oxide (NiO) and molybdenum trioxide (MoO 3 ) with aluminum as a reducing agent. So that oxide precursors with 100 % excess aluminum on stoichiometric composition at different times were milled to perform complete reduction operations. Subsequently, X‐ray diffraction (XRD) analysis was performed for phase analysis and scanning electron microscopy (SEM) was used to investigate the microstructure. It was found that oxide precursors with 100 % excess aluminum on stoichiometric composition were reduced after 50 h of milling and nickel molybdenum/alumina composite was produced. On the other hand, to compare the activity of Ni−Mo/Al 2 O 3 two different catalysts (57 NiMo, 80 NiMo) were also produced by the milling method. The specimens were transformed into pills of 10 mm in diameter and 3 mm in height at 900 MPa pressure. A furnace under an argon atmosphere at a temperature of 1400 °C was used to sinter the produced pills. Finally, the hydrogen evolution activity of this sample was investigated by linear polarization tests and impedance spectroscopy in 1 M KOH solution. The sample reduced with 100 % excess aluminum showed higher activity than the stoichiometric combination, with −62 mV cathodic‐Tafel slope, −70 mV over‐potential at a current density of −10 mA cm −2 and a charge transfer resistance of 126.6 ohms.
- 1 December 2020
- Published by Wiley in ChemistrySelect
- Vol. 5 (45) , 14282-14287
Synthesis, Characterization and Investigation of Hydrogen Evolution Activity of Ni‐Mo/Al 2 O 3 Composite
In the present study, the hydrogen evolution activity of the Ni−Mo/Al 2 O 3 catalyst was investigated. This catalyst was produced by milling of oxide precursors of nickel oxide (NiO) and molybdenum trioxide (MoO 3 ) with aluminum as a reducing agent. So that oxide precursors with 100 % excess aluminum on stoichiometric composition at different times were milled to perform complete reduction operations. Subsequently, X‐ray diffraction (XRD) analysis was performed for phase analysis and scanning electron microscopy (SEM) was used to investigate the microstructure. It was found that oxide precursors with 100 % excess aluminum on stoichiometric composition were reduced after 50 h of milling and nickel molybdenum/alumina composite was produced. On the other hand, to compare the activity of Ni−Mo/Al 2 O 3 two different catalysts (57 NiMo, 80 NiMo) were also produced by the milling method. The specimens were transformed into pills of 10 mm in diameter and 3 mm in height at 900 MPa pressure. A furnace under an argon atmosphere at a temperature of 1400 °C was used to sinter the produced pills. Finally, the hydrogen evolution activity of this sample was investigated by linear polarization tests and impedance spectroscopy in 1 M KOH solution. The sample reduced with 100 % excess aluminum showed higher activity than the stoichiometric combination, with −62 mV cathodic‐Tafel slope, −70 mV over‐potential at a current density of −10 mA cm −2 and a charge transfer resistance of 126.6 ohms.
- 26 November 2019
- Published by Springer Nature in Ionics
- Vol. 26 (3) , 1491-1505
Ternary nanostructured MZnCo oxides (M=Al, Mg, Cu, Fe, Ni) prepared by hydrothermal method as excellent charge storage devices
- 26 November 2019
- Published by Springer Nature in Ionics
- Vol. 26 (3) , 1491-1505
Ternary nanostructured MZnCo oxides (M=Al, Mg, Cu, Fe, Ni) prepared by hydrothermal method as excellent charge storage devices
- Open Access
- 28 September 2019
- Published by Springer Nature in SN Applied Sciences
- Vol. 1 (10) , 1303
Charge storage properties of mixed ternary transition metal ferrites MZnFe oxides (M = Al, Mg, Cu, Fe, Ni) prepared by hydrothermal method
- 28 September 2019
- Published by Springer Nature in SN Applied Sciences
- Vol. 1 (10) , 1303
Open AccessCharge storage properties of mixed ternary transition metal ferrites MZnFe oxides (M = Al, Mg, Cu, Fe, Ni) prepared by hydrothermal method