Qing Xie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Qing Xie has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Wanshui Han
School of Highway, Chang’an University, Xi’an 710064, China
3 shared publications - Guangzhong Gao
School of Highway, Chang’an University, Xi’an 710064, China
2 shared publications - Yangguang Yuan
Xi’an University of Architecture & Technology
2 shared publications Kun Xu
Master, Anhui Transport Consulting and Design Institute Co., Ltd., Wutong Rd., Hefei, Anhui 230000, China
1 shared publication- Xiao Chen
Lecturer, Highway College, Chang’an Univ., Xi’an, Shaanxi 710064, China
1 shared publication - Xiaodong Liu
Master, Highway College, Chang’an Univ., Xi’an 710064, China
1 shared publication
Latest Publications
- 8 July 2019
- Published by Emerald Publishing in Engineering Computations
- Vol. 36 (6) , 1950-1976
Improving the bending response of four-node quadrilateral and eight-node hexahedral elements for Cosserat elasticity problems
Purpose: Poor bending response is a major shortcoming of lower-order elements due to excessive representation of shear stress/strain field. Advanced finite element (FE) formulations for classical elasticity enhance the bending response by either nullifying or filtering some of the symmetric shear stress/strain modes. Nevertheless, the stress/strain field in Cosserat elasticity is asymmetric; consequently any attempt to nullify or filter the anti-symmetric shear stress/strain modes may lead to failure in the constant couple-stress patch test where the anti-symmetric shear stress/strain field is linear. This paper aims at enhancing the bending response of lower-order elements for Cosserat elasticity problems. Design/methodology/approach: A four-node quadrilateral and an eight-node hexahedron are formulated by hybrid-stress approach. The symmetric stress is assumed as those of Pian and Sumihara and Pian and Tong. The anti-symmetric stress components are first assumed to be completely linear in order to pass the constant couple-stress patch test. The linear modes are then constrained with respect to the prescribed body-couple via the equilibrium conditions. Findings: Numerical tests show that the hybrid elements can strictly pass the constant couple-stress patch test and are markedly more accurate than the conventional elements as well as the incompatible elements for bending problems in Cosserat elasticity. Originality/value: This paper proposes a hybrid FE formulation to improve the bending response of four-node quadrilateral and eight-node hexahedral elements for Cosserat elasticity problems without compromising the constant couple-stress patch test.
- 8 July 2019
- Published by Emerald Publishing in Engineering Computations
- Vol. 36 (6) , 1950-1976
Improving the bending response of four-node quadrilateral and eight-node hexahedral elements for Cosserat elasticity problems
Purpose: Poor bending response is a major shortcoming of lower-order elements due to excessive representation of shear stress/strain field. Advanced finite element (FE) formulations for classical elasticity enhance the bending response by either nullifying or filtering some of the symmetric shear stress/strain modes. Nevertheless, the stress/strain field in Cosserat elasticity is asymmetric; consequently any attempt to nullify or filter the anti-symmetric shear stress/strain modes may lead to failure in the constant couple-stress patch test where the anti-symmetric shear stress/strain field is linear. This paper aims at enhancing the bending response of lower-order elements for Cosserat elasticity problems. Design/methodology/approach: A four-node quadrilateral and an eight-node hexahedron are formulated by hybrid-stress approach. The symmetric stress is assumed as those of Pian and Sumihara and Pian and Tong. The anti-symmetric stress components are first assumed to be completely linear in order to pass the constant couple-stress patch test. The linear modes are then constrained with respect to the prescribed body-couple via the equilibrium conditions. Findings: Numerical tests show that the hybrid elements can strictly pass the constant couple-stress patch test and are markedly more accurate than the conventional elements as well as the incompatible elements for bending problems in Cosserat elasticity. Originality/value: This paper proposes a hybrid FE formulation to improve the bending response of four-node quadrilateral and eight-node hexahedral elements for Cosserat elasticity problems without compromising the constant couple-stress patch test.
- 1 April 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Performance of Constructed Facilities
- Vol. 33 (2)
Load Effect, Safety Assessment, and Traffic Strategy of Multigirder Bridges under Lateral Eccentric Customized Transport Vehicle
Customized transport vehicles (CTVs) are usually required to travel along the bridge centerline at low speed. However, emergency situations might occur on the bridge during the passing of a CTV and result in partial closure of the traffic lane. To investigate whether the CTV could pass over multigirder bridges in a manner of lateral eccentric load, five critical CTVs were extracted from long-term recorded data, and the dynamic simulation analysis of 360 different CTV load cases was accomplished. Bending bearing safety assessments of small-to-medium-span multigirder bridges under lateral eccentric CTV loads were conducted and the applicability of specified axle weight limits analyzed by using a load rating method, in which the partial factor of CTV load effect is optimized considering the balance between failure cost and benefit. The results show that when the lateral eccentric distance is not greater than 2.5 m, all safety indices are lower than 0.879 and the bending bearing capacities of multigirder bridges are deemed to meet safety requirements. The safety indices of bridges under fully loaded critical CTVs are lower than 0.977, and the specified CTV axle weight limits are applicable when the lateral eccentric distance reaches 2.5 m. To prevent the structure from entering the plastic stage, the lateral eccentric distances of C-IV and C-V, which denote the fourth and fifth vehicle type, are suggested to be less than 2.0 m when they pass over prestressed T-beam bridges.
- 1 April 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Performance of Constructed Facilities
- Vol. 33 (2)
Load Effect, Safety Assessment, and Traffic Strategy of Multigirder Bridges under Lateral Eccentric Customized Transport Vehicle
Customized transport vehicles (CTVs) are usually required to travel along the bridge centerline at low speed. However, emergency situations might occur on the bridge during the passing of a CTV and result in partial closure of the traffic lane. To investigate whether the CTV could pass over multigirder bridges in a manner of lateral eccentric load, five critical CTVs were extracted from long-term recorded data, and the dynamic simulation analysis of 360 different CTV load cases was accomplished. Bending bearing safety assessments of small-to-medium-span multigirder bridges under lateral eccentric CTV loads were conducted and the applicability of specified axle weight limits analyzed by using a load rating method, in which the partial factor of CTV load effect is optimized considering the balance between failure cost and benefit. The results show that when the lateral eccentric distance is not greater than 2.5 m, all safety indices are lower than 0.879 and the bending bearing capacities of multigirder bridges are deemed to meet safety requirements. The safety indices of bridges under fully loaded critical CTVs are lower than 0.977, and the specified CTV axle weight limits are applicable when the lateral eccentric distance reaches 2.5 m. To prevent the structure from entering the plastic stage, the lateral eccentric distances of C-IV and C-V, which denote the fourth and fifth vehicle type, are suggested to be less than 2.0 m when they pass over prestressed T-beam bridges.
- 1 November 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 31 (6)
Site-Specific Extra-Heavy Truck Load Characteristics and Bridge Safety Assessment
Recently, the occurrence frequency of extra-heavy trucks (EHTs, gross weight ) in China has significantly arisen due to the increasing demand of heavy freight transportation. Load characteristics, such as traveling speed, axle weight, and axle distance, of EHTs are different from those of normal traffic loads and vary by region. In the present study, the site-specific load characteristics of EHTs are analyzed based on weigh-in-motion (WIM) data measured from two typical routes of China. Then, the EHT load cases are extracted and a bridge–vehicle simulation is conducted. Finally, the bending capacities of small- to medium-span bridges are assessed. It is found that more attention should be paid to the site-specific load characteristics of EHTs because they are significantly different among different routes. The focused small- to medium-span bridges under EHT load can satisfy the safety requirements and the safety reserves of the bending capacity of such bridges on Chinese highway, which are higher than those of Chinese expressways under EHT load.- 1 November 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 31 (6)
Site-Specific Extra-Heavy Truck Load Characteristics and Bridge Safety Assessment
Recently, the occurrence frequency of extra-heavy trucks (EHTs, gross weight ) in China has significantly arisen due to the increasing demand of heavy freight transportation. Load characteristics, such as traveling speed, axle weight, and axle distance, of EHTs are different from those of normal traffic loads and vary by region. In the present study, the site-specific load characteristics of EHTs are analyzed based on weigh-in-motion (WIM) data measured from two typical routes of China. Then, the EHT load cases are extracted and a bridge–vehicle simulation is conducted. Finally, the bending capacities of small- to medium-span bridges are assessed. It is found that more attention should be paid to the site-specific load characteristics of EHTs because they are significantly different among different routes. The focused small- to medium-span bridges under EHT load can satisfy the safety requirements and the safety reserves of the bending capacity of such bridges on Chinese highway, which are higher than those of Chinese expressways under EHT load.