PKPeter Kollár

Peter Kollár

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Peter Kollár has a total of 65 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Magnetic Properties of the Iron-Based SMCs With Al 2 O 3 Insulation

    by Peter Kollár, Martin Tkáč, Ján Füzer, Robert Maciaszek, Mária Fáberová, Radovan Bureš

    Iron-based soft magnetic composites (SMCs) insulated with Al₂O₃ are promising for electromagnetic applications requiring low magnetic losses and isotropic magnetic behavior. This study investigates the effect of dry coating processing duration (15 min and 30 min) and Al₂O₃ content (2 wt.% - 15 wt.%) on the microstructure and magnetic properties of ring-shaped Fe@Al2O3 SMCs. Microstructural analysis by SEM and EDS confirmed the distribution and clustering of Al2O3 at iron particle interfaces, while magnetic characterization included coercivity, hysteresis loss and their separation, frequency-dependent total energy loss and complex permeability. The results show that shorter dry coating times preserve higher permeability and lower losses, whereas longer dry coating times improve the permeability cut-off frequency but increase coercivity and reduce permeability, especially at higher Al2O3 contents. These findings demonstrate that both Al2O3 content and dry coating time are critical for optimizing the trade-off between loss minimization, permeability, and high-frequency performance in iron-based SMCs.

  • Open Access

    Influence of Interparticle Electrical Insulators on the Magnetic Permeability of NiFeMo-Based Soft Magnetic Composites

    by Martin Tkáč, Peter Kollár, Denisa Olekšáková, Robert Maciaszek, Mária Fáberová, Radovan Bureš

    Soft magnetic composites represent a promising class of materials for a wide range of applications due to their low eddy current losses and favorable magnetic properties, which make them suitable for higher frequency electromagnetic devices. In this study, NiFeMo-based soft magnetic composites incorporating different electrical insulators are investigated. Hexagonal boron nitride and aluminium oxide were added separately at identical volume fractions, and their influence on relative permeability, the real part of complex relative permeability and its frequency stability, and total energy loss was examined. The results demonstrate that, even at the same insulator content, the type of electrical insulator has a pronounced impact on the overall magnetic behavior of the soft magnetic composites: hexagonal boron nitride improves frequency stability of the real part of complex relative permeability and effectively reduces energy loss, while aluminium oxide provides slightly higher maximum relative permeability but with less favorable frequency characteristics. These findings highlight the crucial role of insulator selection in optimizing the performance of soft magnetic composites and provide valuable insights for tailoring high-performance, low-loss soft magnetic materials.

  • Consolidated Fe/FeSi Mixtures for Applications Requiring Increased Frequency Stability of Magnetic Properties

    by Zuzana Birčáková, Radovan Bureš, Mária Fáberová, Miloš Jakubčin, Ivan Škorvánek, Peter Kollár, Ján Füzer, Soundariya Ravi

    The study investigates the effect of the ratio of Fe/FeSi, as well as the different process additives and compaction parameters, on the magnetic properties of Fe-6.5Si/Fe@phosphate soft magnetic composites, obtained by a method of mixing of different commercially used powder materials. With the worlds´ rapid advancement in 5G, and the development of 6G mobile communications, the robotics, the emerging new applications as electrical vehicles, or the renewable energy industries as photovoltaic technology, the soft magnetic materials components for power and electronic devices operating at high frequencies towards megahertz range and beyond, are urgently required. The goal of improving the high frequency characteristics of the resulting composites with concurrently maintained their cost-effective mass production capability was fulfilled, and the compositions with a significantly enhanced frequency stability of magnetic permeability were found (e.g. for 50/50 wt. % ratio: stable real part of complex relative permeability of ~65, the resonant frequency of ~1 MHz). The relatively low core energy losses (~80 J/m3 at 1 kHz, 0.2 T) is ensured by a sufficiently high specific resistivity (~0.1 Ω.cm), the values comparable with the current literature ones. The assessment of magnetic and electrical properties indicates the effective insulation of ferromagnetic particles, and the inorganic insulation furthermore enables the Fe-6.5Si powder to be used as a ferromagnetic component for composites intended also to higher temperature applications.

  • Open Access

    Magnetic loss reduction in angularly stacked grain-oriented steel cores under normal compressive stress

    by S. Dobák, F. Onderko, J. Füzer, I. Petryshynets, P. Kollár, F. Kováč

    The effect of compressive stress applied normal to the lamination surface on magnetic behavior is investigated in stacked grain-oriented Fe–Si ring cores with controlled angular misalignment between rolling directions (RDs) in neighboring layers. Three angular configurations, θ=0°, 60°, and 90°, are examined under normal stress levels up to 6 MPa. Magnetic characterization combines AC loss measurements with first-order reversal curve (FORC) analysis to resolve stress-induced changes in domain wall dynamics. The results reveal that relatively low normal compressive stresses (∼0.5–2 MPa) can significantly reduce magnetic losses at power frequencies, primarily through suppression of excess loss associated with dynamic domain wall motion. FORC fingerprints indicate that lower normal stress promotes magnetically softer processes governed by 180° domain walls, while higher stresses progressively broaden the distribution of switching fields. The loss-reducing effect of normal stress is most pronounced in non-shifted and moderately shifted configurations and weakens with increasing angular misalignment. These findings demonstrate that normal compressive stress, often unavoidable in practical core assemblies, can act as an effective loss-reducing factor when combined with appropriate lamination topology.

  • Deformation structure and magnetic properties of iron powder core compacted at high pressure

    by Radovan Bureš, Fáberová Mária, Soundariya Ravi, Vladyslav Kostiuk, Zuzana Birčáková, Ján Füzer, Peter Kollár

    This study investigates how compaction pressure and die shape influence the density distribution and related magnetic and electrical properties of pure iron based green compacts. By combining empirical densification models with geometry-specific corrections for wall friction and shear deformation, numerical simulations were conducted for three die types: cylindrical, prismatic, and ring. The simulations predict spatial variations in densification that align with experimental observations from optical microscopy. Results show that high compaction pressures (up to 2500 MPa) can enhance magnetic performance by increasing density and reducing porosity, but they also cause significant inhomogeneities, especially in cylindrical shapes, due to stress localisation near die walls. Ring-shaped compacts demonstrate better uniformity in both density and magnetic properties, confirming the importance of geometry-dependent modelling of compaction. Surface flash formation and grain deformation at the die–punch interface align with shear-enhanced densification zones forecasted by the model. Overall, the findings emphasise the need to consider both friction and shear effects when designing powder metallurgy processes for soft magnetic materials.


  • Open Access

    Magnetic losses in soft magnetic composites and ferrites under rectangular asymmetric excitation

    by S. Dobák, F. Onderko, J. Füzer, P. Kollár

    Magnetic losses in soft magnetic materials subjected to non-sinusoidal excitation are of increasing importance in the design and optimization of power electronic components. Conventional loss models and measurement standards, primarily developed for sinusoidal induction waveforms, often fail to accurately predict losses under pulsed excitation typical of switched-mode power supplies. In this study, a simplified implementation of the Statistical Theory of Losses is applied to two heterogeneous soft magnetic materials: an Fe–Si soft magnetic composite and a Mn–Zn spinel ferrite. Magnetic losses were experimentally characterized under sinusoidal and triangular polarization using a digitally controlled hysteresisgraph-wattmeter. The total losses were decomposed into hysteresis, classical, and excess components, allowing for parameter identification and prediction of loss behavior under symmetric and asymmetric rectangular excitations. The predicted energy losses, derived solely from sinusoidal measurements, show excellent agreement with experimental data across a wide range of frequencies and duty cycles. The proposed method provides a physically based yet computationally simple approach for modeling dynamic magnetic losses in materials relevant to power electronics, facilitating more accurate design of magnetic components under realistic excitation conditions.

  • Influence of Mechanical Milling Intensity and Powder Surface Treatment on Energy Losses of Fe Compacts

    by L. Provázková, D. Olekšáková, P. Kollár, J. Adamko, M. W. Najgebauer

    The soft magnetic compacted powdered materials are used in a variety of electromagnetic applications such as electromotors, magnetic circuits of valves, cores for various inductors in computers, relays, disk drives, printers, hearing aid devices and others. These materials are used due to their relatively easy magnetization and demagnetization, maximum permeability, high magnetic saturation induction, low coercivity, low core losses. Soft magnetic compacted powder materials have high application potential based also on isotropic 3D behaviour, mechanical stability, low-cost production and they offer possibility for environmentally friendly recycling. This work focuses on the detailed description of the energy loss separation for dc and ac low frequency magnetic fields of Fe-based compacted powder. We analyzed magnetic losses of the soft magnetic materials consisting of insulated iron particles according to Bertotti’s theories. The surfaces of the iron poder particles were mechanically smoothed and the ring-shaped compacts were prepared by the high-pressure compaction. The analyze of total energy losses revealed the best magnetic properties of the material with mechanically smoothed surgaces of powder particles. Particular attention was paid to the processes of mechanical surface treatment of powder particles, coating and pressing, which have a major influence on the final properties of the materials. It is expected that optimization of these processes can significantly reduce energy losses and improve the magnetic properties of the materials.


  • Open Access

    Anisotropy of losses in non-segmented assemblies of grain-oriented steel with circular easy axis distribution

    by S. Dobák, J. Füzer, I. Petryshynets, P. Kollár, F. Kováč

    This study explores the frequency-dependent magnetic losses in grain-oriented non-segmented cores with layers shifted by a constant angle, creating a circular distribution of easy axes across the core, up to 500 Hz. This innovative approach reduces magnetic losses by aligning the flux with the rolling direction in each layer, enabling the development of energy-efficient cores for AC rotating machines. We decompose the total losses into hysteresis and dynamic components as functions of frequency, peak induction, and shifting angle. The results reveal that this anisotropy predominantly affects the domain wall-generated losses, including both static and dynamic components. Notably, shifting the layers by ∼60° minimizes hysteresis losses by optimizing the alignment of the easy magnetization axes with the hard axes between adjacent layers. The dynamic hysteresis loops are decomposed into their respective portions, demonstrating the contributions of each individual loss component.


  • Open Access

    Effect of Powder Particle Surface Treatment on DC Magnetic Properties of Compacted Iron Cores

    by Martin Tkáč, Peter Kollár, Robert Maciaszek, Samuel Dobák, Ján Füzer, Denisa Olekšáková, Radovan Bureš, Mária Fáberová

    Soft magnetic iron finds practical use in many applications, such as electromagnets and relays. In order for these devices to work effectively, it is necessary to know their DC magnetic properties. Soft magnetic compacted powder cores possess lower permeability than powder particles from which they were prepared due to the inner demagnetization factor caused by the existence of pores in the core structure. The aim of the work was to determine the effect of surface mechanical treatment of iron powder particles of two different size fractions, leading either to an increase in the demagnetization factor or to a positive effect on the DC magnetic properties of the resulting compacted cores. For samples prepared from smaller powder particles, we found that despite the increase in inner demagnetization factor as a result of the smoothing procedure, the differential relative permeability increased, and total energy loss decreased.