Shuxian Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shuxian Zheng has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Xiubing Jing
Key Laboratory of Equipment Design and Manufacturing Technology, Tianjin University, Tianjin 300072, China
4 shared publications - Huaizhong Li
School of Engineering & Built Environment, Gold Coast Campus, Griffith University, Southport, QLD 4222, Australia
2 shared publications - Jia Li
Tianjin Key Laboratory of Equipment Design and Manufacturing Technology, School of Mechanical Engineering, Tianjin University, Tianjin, 300354, China
2 shared publications - Jian Qi
Tianjin Key Laboratory of Equipment Design and Manufacturing Technology, School of Mechanical Engineering, Tianjin University, Tianjin, 300354, China
2 shared publications Syed Husain Imran Jaffery
School of Mechanical and Manufacturing Engineering, National University of Sciences and Technology, Islamabad, Pakistan
2 shared publicationsChengjuan Yang
Tianjin University
1 shared publication
Latest Publications
- 2 March 2026
- Published by Elsevier in ISA Transactions
- Vol. 172, 320-336
Adaptive milling chatter detection in variable tool-workpiece systems: A novel approach using signal reconstruction and energy ratio
- 2 March 2026
- Published by Elsevier in ISA Transactions
- Vol. 172, 320-336
Adaptive milling chatter detection in variable tool-workpiece systems: A novel approach using signal reconstruction and energy ratio
- 28 October 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (7-8) , 3271-3284
On cutting forces considering elastic recovery accumulation in micro-milling process
- 28 October 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (7-8) , 3271-3284
On cutting forces considering elastic recovery accumulation in micro-milling process
- 5 December 2023
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 257, 128595
Thermally reversible hydrogels printing of customizable bio-channels with curvature
- 5 December 2023
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 257, 128595
Thermally reversible hydrogels printing of customizable bio-channels with curvature
- 22 October 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (31) , 9696-9705
Surface modification and effects on tribology by laser texturing in Al2O3
We investigate the surface modification by laser texturing and effects thereof on the tribological performance in A l 2 O 3 . By detailed observation for microstructure evolution, it has been shown that there were three distinct modification morphologies by laser treatment: dense surface microfeatures, “coral” dendritic structures, and coarse grains. X-ray diffraction (XRD) results indicated that there was no formation of metastable phases due to low supercooling in solidification in the nanosecond laser regime. The formation of AlN compounds in the laser-treated region was examined by using x-ray photoelectron spectroscopy (XPS), which led to dense surface microfeatures and randomly distributed pores formation in the laser treated region. The formation of “coral” dendritic structures on the edge of groove and coarse grains in the vicinity of the laser surface was attributed to the fast-cooling rates. Wear tests were carried out to analyze the effect of laser texturing on tribological performance. The results of coefficients of friction (COF) illustrated that laser texturing can significantly improve COFs for dry friction; however, it decreases the COFs for wet friction. The mechanism of wear was explained based on a SEM measurement for worn surfaces; the formation of surface texture can store abrasive particles and debris lead to hydrodynamic lubricant film formation and the COFs significantly reducing for wet friction.
- 22 October 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (31) , 9696-9705
Surface modification and effects on tribology by laser texturing in Al2O3
We investigate the surface modification by laser texturing and effects thereof on the tribological performance in A l 2 O 3 . By detailed observation for microstructure evolution, it has been shown that there were three distinct modification morphologies by laser treatment: dense surface microfeatures, “coral” dendritic structures, and coarse grains. X-ray diffraction (XRD) results indicated that there was no formation of metastable phases due to low supercooling in solidification in the nanosecond laser regime. The formation of AlN compounds in the laser-treated region was examined by using x-ray photoelectron spectroscopy (XPS), which led to dense surface microfeatures and randomly distributed pores formation in the laser treated region. The formation of “coral” dendritic structures on the edge of groove and coarse grains in the vicinity of the laser surface was attributed to the fast-cooling rates. Wear tests were carried out to analyze the effect of laser texturing on tribological performance. The results of coefficients of friction (COF) illustrated that laser texturing can significantly improve COFs for dry friction; however, it decreases the COFs for wet friction. The mechanism of wear was explained based on a SEM measurement for worn surfaces; the formation of surface texture can store abrasive particles and debris lead to hydrodynamic lubricant film formation and the COFs significantly reducing for wet friction.
- 19 May 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (15) , 4434-4442
Effect of surface modification on wettability and tribology by laser texturing in Al2O3
The life of ceramic tools restricts the development of the manufacturing industry and can be increased through the enhancement of surface performance. Laser surface texturing is a feasible technology to improve ceramic tool life based on the relationship between surface properties and the laser-texturing process. In this study, A l 2 O 3 substrates have been textured by an ytterbium fiber laser system with a wavelength of 1064 nm and a pulse duration of 50 ns. First, the damage threshold of A l 2 O 3 was measured to provide a basis for selecting laser-texturing parameters. The surface morphology was characterized using a white confocal scanning microscope and a scanning electron microscope to investigate the characteristics of laser processing. Water contact angles were measured to investigate the relationship between laser parameters and changes in wettability. The surface energy of the superhydrophobic ceramic was calculated based on the contact angle. Combined X-ray photoelectron spectroscopy (XPS) measurement was used to explore the mechanism of wettability changes from the chemical component and microstructure perspectives. The friction coefficient of A l 2 O 3 was determined by a ball-on-disc wear test. The results showed that laser texturing can significantly improve the surface hydrophobicity and friction stability.
- 19 May 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (15) , 4434-4442
Effect of surface modification on wettability and tribology by laser texturing in Al2O3
The life of ceramic tools restricts the development of the manufacturing industry and can be increased through the enhancement of surface performance. Laser surface texturing is a feasible technology to improve ceramic tool life based on the relationship between surface properties and the laser-texturing process. In this study, A l 2 O 3 substrates have been textured by an ytterbium fiber laser system with a wavelength of 1064 nm and a pulse duration of 50 ns. First, the damage threshold of A l 2 O 3 was measured to provide a basis for selecting laser-texturing parameters. The surface morphology was characterized using a white confocal scanning microscope and a scanning electron microscope to investigate the characteristics of laser processing. Water contact angles were measured to investigate the relationship between laser parameters and changes in wettability. The surface energy of the superhydrophobic ceramic was calculated based on the contact angle. Combined X-ray photoelectron spectroscopy (XPS) measurement was used to explore the mechanism of wettability changes from the chemical component and microstructure perspectives. The friction coefficient of A l 2 O 3 was determined by a ball-on-disc wear test. The results showed that laser texturing can significantly improve the surface hydrophobicity and friction stability.
- 1 September 2019
- Published by Springer Nature in Journal of Bionic Engineering
- Vol. 16 (5) , 814-827
A Bifurcated Vascular Channel Construction Method based on Diploic Vein Characteristics
- 1 September 2019
- Published by Springer Nature in Journal of Bionic Engineering
- Vol. 16 (5) , 814-827
A Bifurcated Vascular Channel Construction Method based on Diploic Vein Characteristics
- 1 January 2019
- Published by Elsevier in Computers in Biology and Medicine
- Vol. 104, 70-80
A mosaic structure multi-level vascular network design for skull tissue engineering
- 1 January 2019
- Published by Elsevier in Computers in Biology and Medicine
- Vol. 104, 70-80
A mosaic structure multi-level vascular network design for skull tissue engineering
- Open Access
- 7 August 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 394 (2) , 022061
A vascular fabrication method based on sacrificial material and spraying process
In tissue engineering, the lack of vascular structures often leads to massive cell death inside the scaffold, it is necessary to construct vascular structures in scaffolds. This paper presented a method for fabricating blood vessels based on sacrificial materials and spraying process. Sucrose was used as the sacrificial material to prepare the vascular core, the SA/PVA gel formulated from sodium alginate (SA) and polyvinyl alcohol (PVA) was used as vascular material. The optimal proportion of SA/PVA gel material was determined by orthogonal experiments: SA: 4 wt%, PVA: 5 wt%, CaCl2: 4 wt%, and its elastic modulus and porosity were 993.19 kPa and 89.23%. The spraying process utilized high-pressure air flow to coat the SA/PVA gel on the vascular core, and then it was cross-linked in CaCl2 solution, and the hollow vascular structure can be obtained by removing the vascular core in an aqueous solution. This method allows rapid, low-cost preparation of vascular structures.
- 7 August 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 394 (2) , 022061
Open AccessA vascular fabrication method based on sacrificial material and spraying process
In tissue engineering, the lack of vascular structures often leads to massive cell death inside the scaffold, it is necessary to construct vascular structures in scaffolds. This paper presented a method for fabricating blood vessels based on sacrificial materials and spraying process. Sucrose was used as the sacrificial material to prepare the vascular core, the SA/PVA gel formulated from sodium alginate (SA) and polyvinyl alcohol (PVA) was used as vascular material. The optimal proportion of SA/PVA gel material was determined by orthogonal experiments: SA: 4 wt%, PVA: 5 wt%, CaCl2: 4 wt%, and its elastic modulus and porosity were 993.19 kPa and 89.23%. The spraying process utilized high-pressure air flow to coat the SA/PVA gel on the vascular core, and then it was cross-linked in CaCl2 solution, and the hollow vascular structure can be obtained by removing the vascular core in an aqueous solution. This method allows rapid, low-cost preparation of vascular structures.