Uğur Aybarç
Research Subjects
Uğur Aybarç has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Onur Ertuğrul
Izmir Katip Celebi University
2 shared publications A. Kara
1 shared publication- Batuhan Doğdu
CMS Jant ve Makina San. A.Ş.
1 shared publication Derya Dispinar
Istanbul University
1 shared publication- Esra Dokumaci
DOKUZ EYLÜL ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ, METALURJİ VE MALZEME MÜHENDİSLİĞİ BÖLÜMÜ, ÜRETİM METALURJİSİ ANABİLİM DALI
1 shared publication H.E. Çubuklusu
1 shared publication
Latest Publications
- 27 September 2021
- Published by Celal Bayar University Journal of Science in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
- Vol. 17 (3) , 275-283
Determination Of The Effect Of Cooling Rate And Strontium Amount On Eutectic Si Modification Performance Of A356 Alloy Via Casting Simulation
It is well-known that strontium addition into molten metal as a eutectic modifier increases the elongation and toughness values of the cast parts by refining the eutectic phases. However, when over-modification occurs, porosity increases due to some unwanted physical and chemical reactions that develop within the structure. On the other hand, it has been seen that high cooling rates tend to reduce the porosity of the alloy, decrease grain size and secondary dendrite arm spacing and refine eutectic silicon phase on Al-Si casting alloys. Within the scope of this project, it is aimed to investigate the effects of the cooling rate of cast part and the addition amount of strontium on the silicon modification behavior of Al A356 (AlSi7Mg) alloy parts using casting simulation environment. In order to examine the effect of strontium addition, 150, 250, 350 and 450 parts per million of strontium additions were chosen based on thermodynamic calculations. After the casting session of each Al A356 composition with different strontium amount by using special designed 5-spoke mold on casting simulation, thermal analysis was done by obtained thermocouple data from casting part’s each spoke. Obtained thermal analysis data was interpreted with the casting simulation outputs. Within all aspects, the 150 parts per million strontium addition on Al A356 alloy has been identified as the most useful simulation model in terms of casting performance.
- 27 September 2021
- Published by Celal Bayar University Journal of Science in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
- Vol. 17 (3) , 275-283
Determination Of The Effect Of Cooling Rate And Strontium Amount On Eutectic Si Modification Performance Of A356 Alloy Via Casting Simulation
It is well-known that strontium addition into molten metal as a eutectic modifier increases the elongation and toughness values of the cast parts by refining the eutectic phases. However, when over-modification occurs, porosity increases due to some unwanted physical and chemical reactions that develop within the structure. On the other hand, it has been seen that high cooling rates tend to reduce the porosity of the alloy, decrease grain size and secondary dendrite arm spacing and refine eutectic silicon phase on Al-Si casting alloys. Within the scope of this project, it is aimed to investigate the effects of the cooling rate of cast part and the addition amount of strontium on the silicon modification behavior of Al A356 (AlSi7Mg) alloy parts using casting simulation environment. In order to examine the effect of strontium addition, 150, 250, 350 and 450 parts per million of strontium additions were chosen based on thermodynamic calculations. After the casting session of each Al A356 composition with different strontium amount by using special designed 5-spoke mold on casting simulation, thermal analysis was done by obtained thermocouple data from casting part’s each spoke. Obtained thermal analysis data was interpreted with the casting simulation outputs. Within all aspects, the 150 parts per million strontium addition on Al A356 alloy has been identified as the most useful simulation model in terms of casting performance.
- 31 December 2020
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 4 (4) , 234-243
Effect of Ultrasonic Treatment Parameters on Microstructural and Mechanical Properties of A356 Aluminum Alloy
The aim of this study is to investigate the effect of ultrasonic treatment on the microstructural and mechanical properties of A356 aluminum al-loy. Ultrasonic treatment was applied to 2 kg and 4 kg molten metals at different melting temperatures (700 oC, 720 oC and 740 oC) for different durations (0, 60, 180 and 300 seconds). Bifilm indices of the samples were also measured after all parameters were tested. The ultimate tensile strength (UTS) and elongation values were used to calculate the Quality Index (QI) of the samples. According to the results, the amount of liquid metal directly affects the the ultrasonic intensity that is produced during the treatment. Maximum UTS and elongation results were determined at 720 oC during 300 seconds for 4 kg casting. Minimum bifilm density val-ue was measured at the same ultrasonic temperature and time.
- 31 December 2020
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 4 (4) , 234-243
Effect of Ultrasonic Treatment Parameters on Microstructural and Mechanical Properties of A356 Aluminum Alloy
The aim of this study is to investigate the effect of ultrasonic treatment on the microstructural and mechanical properties of A356 aluminum al-loy. Ultrasonic treatment was applied to 2 kg and 4 kg molten metals at different melting temperatures (700 oC, 720 oC and 740 oC) for different durations (0, 60, 180 and 300 seconds). Bifilm indices of the samples were also measured after all parameters were tested. The ultimate tensile strength (UTS) and elongation values were used to calculate the Quality Index (QI) of the samples. According to the results, the amount of liquid metal directly affects the the ultrasonic intensity that is produced during the treatment. Maximum UTS and elongation results were determined at 720 oC during 300 seconds for 4 kg casting. Minimum bifilm density val-ue was measured at the same ultrasonic temperature and time.
- Open Access
- 1 December 2020
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 23 (4) , 1265-1275
Effects of Stirring Duration and Casting Temperature in Ultrasonic Assisted Stir Casting of Al A356 Matrix Composites
In the present study, two main parameters as stirring duration and casting temperature were taken into consideration in order to determine the effect of stirring process on mechanical properties of aluminum matrix composites. AlSi7Mg0.3 aluminum alloy and silicon carbide (SiC) particles were used as matrix and reinforcement materials to produce composite samples. Firstly, stirring processes were applied as the combination of mechanical stirring and ultrasonic vibration for the various time as 3-1, 2-2 and 1-3 minutes, respectively. To determine the effect of stirring process, tensile tests were applied to whole samples and Quality Indexes (QI) were calculated by using the results of tensile tests. According to the values of QI, the produced samples with the combination of 1 minute mechanical stirring and 3 minutes ultrasonic vibration showed the maximum mechanical properties. Afterwards, the determined stirring combination was chosen to specify the appropriate molten metal temperature. Three different casting temperatures were addressed as 700˚C, 720˚C and 740˚C. According to mechanical tests results and calculations of QI and metallographic analysis, the maximum mechanical properties were obtained with aluminum composite reinforced with 1 wt. % SiC at 720˚C molten metal temperature by applying 1 minute mechanical stirring and 3 minutes ultrasonic vibration.
- 1 December 2020
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 23 (4) , 1265-1275
Open AccessEffects of Stirring Duration and Casting Temperature in Ultrasonic Assisted Stir Casting of Al A356 Matrix Composites
In the present study, two main parameters as stirring duration and casting temperature were taken into consideration in order to determine the effect of stirring process on mechanical properties of aluminum matrix composites. AlSi7Mg0.3 aluminum alloy and silicon carbide (SiC) particles were used as matrix and reinforcement materials to produce composite samples. Firstly, stirring processes were applied as the combination of mechanical stirring and ultrasonic vibration for the various time as 3-1, 2-2 and 1-3 minutes, respectively. To determine the effect of stirring process, tensile tests were applied to whole samples and Quality Indexes (QI) were calculated by using the results of tensile tests. According to the values of QI, the produced samples with the combination of 1 minute mechanical stirring and 3 minutes ultrasonic vibration showed the maximum mechanical properties. Afterwards, the determined stirring combination was chosen to specify the appropriate molten metal temperature. Three different casting temperatures were addressed as 700˚C, 720˚C and 740˚C. According to mechanical tests results and calculations of QI and metallographic analysis, the maximum mechanical properties were obtained with aluminum composite reinforced with 1 wt. % SiC at 720˚C molten metal temperature by applying 1 minute mechanical stirring and 3 minutes ultrasonic vibration.
- 1 August 2020
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 15 (2) , 638-649
Effect of Al2O3 Particle Size on Mechanical Properties of Ultrasonic-Assisted Stir-Casted Al A356 Matrix Composites
- 1 August 2020
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 15 (2) , 638-649
Effect of Al2O3 Particle Size on Mechanical Properties of Ultrasonic-Assisted Stir-Casted Al A356 Matrix Composites
- 13 August 2018
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 13 (1) , 190-200
The Use of Stirring Methods for the Production of SiC-Reinforced Aluminum Matrix Composite and Validation Via Simulation Studies
- 13 August 2018
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 13 (1) , 190-200
The Use of Stirring Methods for the Production of SiC-Reinforced Aluminum Matrix Composite and Validation Via Simulation Studies
- 1 April 2016
- Published by Index Copernicus in Journal of Achievements in Materials and Manufacturing Engineering
- Vol. 75 (2) , 71-77
The effect of filter type on filling during Low Pressure Die Casting: a numerical study
- 1 April 2016
- Published by Index Copernicus in Journal of Achievements in Materials and Manufacturing Engineering
- Vol. 75 (2) , 71-77
The effect of filter type on filling during Low Pressure Die Casting: a numerical study