Homin Kye
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Homin Kye has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Joon-Wun Kang
Department of Environmental Engineering (YIEST), Yonsei University, 234 Maeji, Heungup, Wonju, 220-710, South Korea
3 shared publications - Yeojoon Yoon
Department of Environmental and Energy Engineering, Yonsei University, Wonju, 26493, Republic of Korea
2 shared publications - Yirga Weldu Abrha
Yonsei Univ, Dept Environm Engn YIEST, 234 Maeji, Wonju 220710, South Korea
2 shared publications - Doorae Lee
Chemical and Environmental Engineering Department, University of Arizona, Tucson, Arizona, 85721, USA
1 shared publication - Heegun Oh
Department of Environmental Engineering, Yonsei University, 1 Yonseidae-gil, Wonju-si, Gangwon-do 26493, Korea
1 shared publication - Joon-Wun Kang
School of Chemical and Bio Engineering
1 shared publication
Latest Publications
- Open Access
- 18 July 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (14) , 4944
Oxidation of Florfenicol and Oxolinic Acid in Seawater by Ozonation
There has been an increase in the use of antibiotics by the aquaculture industry in marine aquaculture for the prevention of diseases in fish. Antibiotics in the water discharged into the sea without treatment can cause disturbances to the marine ecosystem. Therefore, there is a need for research on how the removal of antibiotics used in aquaculture can be achieved. In this study, the removal of two types of antibiotics (florfenicol, FF, and oxolinic acid, OA) used in the aquaculture industry, by ozonation, was evaluated. Currently, there is a lack of research studies on FF and OA removal from seawater by ozonation. Seawater ozonation shows a significantly different oxidation mechanism as compared to that of freshwater. The high amount of Br− in seawater (60 mg/L) allows for a rapid reaction with ozone to produce bromine (HOBr/OBr−) at a rate of 160 M−1s−1. To predict the removal efficiency of antibiotics by ozone and bromine, the species-specific rate constants for the reaction of FF and OA with ozone and bromine were determined. The predicted removal efficiencies of FF and OA using measured rate constants were verified by the ozonation process in water containing bromide ions in similar concentrations as in seawater. The result for FF indicated less than 10% removal during 20 min, with the rate constants of FF with ozone and bromine being 3.2 M−1s−1 and 3.5 M−1s−1, respectively. However, the removal of OA using ozonation was approximately 99% or higher within 90 s. In the presence of bromide ions, approximately 60% of OA was removed by trace ozone within 15 s, and approximately 30% of OA was removed by the generated bromine after 15 s. Comparing the removability of FF and OA used in aquaculture by ozone, it was observed that FF was more difficult to remove because of its low reaction rate constant. Meanwhile, the reaction rates of OA with ozone and bromine were 2.4 × 103 M−1s−1 and 4.0 × 102 M−1s−1, respectively. At the beginning of the reaction, OA was removed by the trace ozone. Subsequently, OA was removed by the generated bromine after the ozone was decomposed.
- 18 July 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (14) , 4944
Open AccessOxidation of Florfenicol and Oxolinic Acid in Seawater by Ozonation
There has been an increase in the use of antibiotics by the aquaculture industry in marine aquaculture for the prevention of diseases in fish. Antibiotics in the water discharged into the sea without treatment can cause disturbances to the marine ecosystem. Therefore, there is a need for research on how the removal of antibiotics used in aquaculture can be achieved. In this study, the removal of two types of antibiotics (florfenicol, FF, and oxolinic acid, OA) used in the aquaculture industry, by ozonation, was evaluated. Currently, there is a lack of research studies on FF and OA removal from seawater by ozonation. Seawater ozonation shows a significantly different oxidation mechanism as compared to that of freshwater. The high amount of Br− in seawater (60 mg/L) allows for a rapid reaction with ozone to produce bromine (HOBr/OBr−) at a rate of 160 M−1s−1. To predict the removal efficiency of antibiotics by ozone and bromine, the species-specific rate constants for the reaction of FF and OA with ozone and bromine were determined. The predicted removal efficiencies of FF and OA using measured rate constants were verified by the ozonation process in water containing bromide ions in similar concentrations as in seawater. The result for FF indicated less than 10% removal during 20 min, with the rate constants of FF with ozone and bromine being 3.2 M−1s−1 and 3.5 M−1s−1, respectively. However, the removal of OA using ozonation was approximately 99% or higher within 90 s. In the presence of bromide ions, approximately 60% of OA was removed by trace ozone within 15 s, and approximately 30% of OA was removed by the generated bromine after 15 s. Comparing the removability of FF and OA used in aquaculture by ozone, it was observed that FF was more difficult to remove because of its low reaction rate constant. Meanwhile, the reaction rates of OA with ozone and bromine were 2.4 × 103 M−1s−1 and 4.0 × 102 M−1s−1, respectively. At the beginning of the reaction, OA was removed by the trace ozone. Subsequently, OA was removed by the generated bromine after the ozone was decomposed.
- Open Access
- 16 March 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (6) , 2015
Comparing Graphene Oxide and Reduced Graphene Oxide as Blending Materials for Polysulfone and Polyvinylidene Difluoride Membranes
Graphene is a single atomic plane of graphite, and it exhibits unique electronic, thermal, and mechanical properties. Exfoliated graphene oxide (GO) contains various hydrophilic functional groups, such as hydroxyl, epoxide, and carboxyl groups, that can modify the hydrophobic characteristics of a membrane surface. Though reduced graphene oxide (rGO) has fewer functional groups than GO, its associated sp2 structures and physical properties can be recovered. A considerable amount of research has focused on the use of GO to obtain a pristine graphene material via reduction processes. In this study, polysulfone (PSf) and polyvinylidene fluoride (PVDF) membranes that were blended with GO and rGO, respectively, were fabricated by using the immersion phase inversion method and an n-methylpyrrolidone (NMP) solvent. Results showed that the graphene nanomaterials, GO and rGO, can change the pore morphology (size and structure) of both PSf and PVDF membranes. The optimum content of both was then investigated, and the highest flux enhancement was observed with the 0.10 wt% GO-blended PSf membrane. The presence of functional groups in GO within prepared PSf and PVDF membranes alters the membrane characteristics to hydrophilic. An antifouling test and rejection efficiency evaluation also showed that the 0.10 wt% membrane provided the best performance.
- 16 March 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (6) , 2015
Open AccessComparing Graphene Oxide and Reduced Graphene Oxide as Blending Materials for Polysulfone and Polyvinylidene Difluoride Membranes
Graphene is a single atomic plane of graphite, and it exhibits unique electronic, thermal, and mechanical properties. Exfoliated graphene oxide (GO) contains various hydrophilic functional groups, such as hydroxyl, epoxide, and carboxyl groups, that can modify the hydrophobic characteristics of a membrane surface. Though reduced graphene oxide (rGO) has fewer functional groups than GO, its associated sp2 structures and physical properties can be recovered. A considerable amount of research has focused on the use of GO to obtain a pristine graphene material via reduction processes. In this study, polysulfone (PSf) and polyvinylidene fluoride (PVDF) membranes that were blended with GO and rGO, respectively, were fabricated by using the immersion phase inversion method and an n-methylpyrrolidone (NMP) solvent. Results showed that the graphene nanomaterials, GO and rGO, can change the pore morphology (size and structure) of both PSf and PVDF membranes. The optimum content of both was then investigated, and the highest flux enhancement was observed with the 0.10 wt% GO-blended PSf membrane. The presence of functional groups in GO within prepared PSf and PVDF membranes alters the membrane characteristics to hydrophilic. An antifouling test and rejection efficiency evaluation also showed that the 0.10 wt% membrane provided the best performance.
- Open Access
- 1 March 2019
- Published by Elsevier in Desalination and Water Treatment
- Vol. 144, 345-354
Chemically treated cactus (Opuntia) as a sustainable biosorbent for the removal of heavy metals from aqueous solution: characterization and adsorption capacity
- 1 March 2019
- Published by Elsevier in Desalination and Water Treatment
- Vol. 144, 345-354
Open AccessChemically treated cactus (Opuntia) as a sustainable biosorbent for the removal of heavy metals from aqueous solution: characterization and adsorption capacity
- Open Access
- 1 September 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (9) , 1502
Removal of Algae, and Taste and Odor Compounds by a Combination of Plant-Mineral Composite (PMC) Coagulant with UV-AOPs: Laboratory and Pilot Scale Studies
The seasonal occurrence of algae blooms in surface waters remains a common problem, such as taste and odor (T&Os), the risk of disinfection by-products (DBPs), and disturbance to water treatment systems. The coagulation efficiency of plant-mineral composite (PMC) coagulant followed by UV-based advanced oxidation processes (UV-AOPs; UV/H2O2 and UV/Cl2) was evaluated for removal of algae, turbidity, dissolved organic matters, and taste and odor compounds in lab-scale and pilot-scale tests. In the lab-scale test, coagulation process with 20 mg/L of PMC shows high removal efficiency of turbidity (94%) and algae (99%) and moderate removal efficiency of UV254 (51%) and geosmin (46%). The pilot test results also show good removal efficiency of turbidity (64%), chlorophyll-a (96%). After PMC coagulation process, the major water factors, which affected the performance of UV-AOPs (i.e., UV transmittance (85–94%), and scavenging factor (64,998–28,516 s−1)), were notably improved, and further degradation of geosmin and 2-methylisoborneol (2-MIB) was achieved in both lab-and pilot-scale tests of the UV-AOPs. The UV/H2O2 process shows higher removal efficiency of geosmin and 2-MIB than the UV/Cl2 process because of the pH effect. The results confirmed that the PMC-based coagulation followed by UV/H2O2 process could be an effective process for the removal of algae, geosmin, and 2-MIB.
- 1 September 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (9) , 1502
Open AccessRemoval of Algae, and Taste and Odor Compounds by a Combination of Plant-Mineral Composite (PMC) Coagulant with UV-AOPs: Laboratory and Pilot Scale Studies
The seasonal occurrence of algae blooms in surface waters remains a common problem, such as taste and odor (T&Os), the risk of disinfection by-products (DBPs), and disturbance to water treatment systems. The coagulation efficiency of plant-mineral composite (PMC) coagulant followed by UV-based advanced oxidation processes (UV-AOPs; UV/H2O2 and UV/Cl2) was evaluated for removal of algae, turbidity, dissolved organic matters, and taste and odor compounds in lab-scale and pilot-scale tests. In the lab-scale test, coagulation process with 20 mg/L of PMC shows high removal efficiency of turbidity (94%) and algae (99%) and moderate removal efficiency of UV254 (51%) and geosmin (46%). The pilot test results also show good removal efficiency of turbidity (64%), chlorophyll-a (96%). After PMC coagulation process, the major water factors, which affected the performance of UV-AOPs (i.e., UV transmittance (85–94%), and scavenging factor (64,998–28,516 s−1)), were notably improved, and further degradation of geosmin and 2-methylisoborneol (2-MIB) was achieved in both lab-and pilot-scale tests of the UV-AOPs. The UV/H2O2 process shows higher removal efficiency of geosmin and 2-MIB than the UV/Cl2 process because of the pH effect. The results confirmed that the PMC-based coagulation followed by UV/H2O2 process could be an effective process for the removal of algae, geosmin, and 2-MIB.