Rafał Andrzejczyk

The present study aims to compare the feasibility of using ultrasound techniques and image processing to obtain comprehensive experimental results on the dynamics of solid–liquid fraction changes during the melting and solidification of coconut oil as a phase change material (PCM). The discussion will focus on the advantages and limitations of various ultrasonic techniques and image data analysis for inspecting materials during phase transitions. Ultrasound enables the detection of phase changes in materials by analysing variations in their acoustic properties, such as wave velocity and amplitude, during transitions. This method is not only cost-effective compared to traditional non-destructive techniques, such as X-ray tomography, but also offers the potential for real-time monitoring in thermal energy storage systems. Furthermore, it can provide valuable information about internal mechanical parameters and the material’s structure. A detailed analysis of the melting and solidification dynamics has been conducted, confirming the feasibility of using ultrasound parameters to assess the reconstruction of material structures during phase changes. This study paves the way for more efficient and cost-effective monitoring of phase change materials in various applications.

Heating, ventilation, and air-conditioning (HVAC) systems account for the largest share of energy consumption in European Union (EU) buildings, representing approximately 40% of the final energy use and contributing significantly to carbon emissions. Latent thermal energy storage (LTES) using phase change materials (PCMs) has emerged as a promising strategy to enhance HVAC efficiency. This review systematically examines the role of latent thermal energy storage using phase change materials (PCMs) in optimizing HVAC performance to align with EU climate targets, including the Energy Performance of Buildings Directive (EPBD) and the Energy Efficiency Directive (EED). By analyzing advancements in PCM-enhanced HVAC systems across residential and commercial sectors, this study identifies critical pathways for reducing energy demand, enhancing grid flexibility, and accelerating the transition to nearly zero-energy buildings (NZEBs). The review categorizes PCM technologies into organic, inorganic, and eutectic systems, evaluating their integration into thermal storage tanks, airside free cooling units, heat pumps, and building envelopes. Empirical data from case studies demonstrate consistent energy savings of 10–30% and peak load reductions of 20–50%, with Mediterranean climates achieving superior cooling load management through paraffin-based PCMs (melting range: 18–28 °C) compared to continental regions. Policy-driven initiatives, such as Germany’s renewable integration mandates for public buildings, are shown to amplify PCM adoption rates by 40% compared to regions lacking regulatory incentives. Despite these benefits, barriers persist, including fragmented EU standards, life cycle cost uncertainties, and insufficient training. This work bridges critical gaps between PCM research and EU policy implementation, offering a roadmap for scalable deployment. By contextualizing technical improvement within regulatory and economic landscapes, the review provides strategic recommendations to achieve the EU’s 2030 emissions reduction targets and 2050 climate neutrality goals.

The following study investigated the melting behavior of coconut oil as a phase-change material in shell-and-tube and shell-and-coil thermal energy storage systems. The primary objective was to deepen the understanding of PCM melting dynamics under varying boundary conditions, aiming to optimize TES designs for renewable energy applications. This research addresses a gap in understanding how different heat-transfer configurations and boundary conditions affect melting efficiency. Experimental setups included two distinct heat-transfer surfaces in a cylindrical shell—a copper tube and a copper coil—tested under constant wall temperatures (34 °C for the tube, 33 °C for the coil) and constant heat flux (597 W/m² for the coil). Findings reveal that melting under constant heat flux takes approximately twice as long as under constant wall temperatures, underscoring the critical role of heat-transfer conditions in TES performance. The liquid fraction was estimated using two approaches: image-based analysis and the volume-averaged temperature method. The former proved less reliable due to geometric limitations, particularly when the heat-transfer surface was distant from the shell wall. Conversely, the latter yielded higher accuracy, especially in the shell-and-tube setup. Due to the scarcity of correlations for constant heat-flux conditions, the novel contribution of this work is the development of a modified semi-empirical correlation for the shell-and-coil TES system. For this purpose, an existing model, which demonstrated strong alignment with experimental data, was adapted. The findings suggest that slower melting under constant heat flux could benefit applications needing sustained heat release, like solar energy systems. Future work could investigate additional PCMs or novel geometries to further improve TES efficiency and scalability.

This study presents the potential of using a natural ventilation system integrated with different combinations of enhancement techniques. The focus was on the perspective of using such configurations of passive ventilation systems (PVSs) in buildings located in different European cities. This work presents the results of obtaining the level of volumetric air flow rate for considering natural ventilation systems. Furthermore, the influences of local weather conditions (temperature, solar radiation, wind speed) were analyzed. Moreover, the year-round operation of all systems was presented. Also noted was the limitation of using PVSs based on the natural draft effect, additionally assisted by wind turbine ventilators in all European localizations. However, for the cities located in the northern part of Europe, it was confirmed that such a system can still meet minimum hygienic recommendations. It was also noted that a system additionally supported by a solar chimney is a much better solution. The best system was a PVS supported by a wind turbine ventilator and solar chimney integrated with PCM accumulation mass. The system should be additionally supported by waste heat from low-temperature sources. In the presented study, a high potential to reduce CO₂ emission from building stock by the recommended system is additionally highlighted. However, there is still a need to analyze the proposed solutions by additional field tests and experimental investigations.

Various types of heat pipes are available to purchase off the shelf, from various manufacturers, but most of them have strictly defined geometry and technical parameters. However, when there is a need to use a heat pipe (HP) with an unusual size and shape or working conditions other than the standard ones, it becomes very costly to order them from manufacturers, especially in small quantities, and only a few producers are willing to fulfill such an order. This paper presents a detailed description and step-by-step method of manufacturing and testing a low-cost HP with specific properties and geometry, cooperating with a modular heat recovery system based on the use of phase change materials (PCM) for electromobility applications. The presented heat pipes were made entirely by hand, primarily with the use of basic workshop tools, without the use of specialized and automated CNC machines. Utensils used during the process were either made by hand or using desktop FDM 3D printers. During the evaluation of heat pipes’ performance within PCM (coconut oil), simple statistical functions were used. One-dimensional and two-dimensional histograms were used to visualize data obtained during this research. The presented method allows the manufacturing of heat pipes that are, on average, able to melt about 35% more PCM than an empty copper pipe with the exact same geometry. The HPs’ performance in coconut oil was evaluated on the basis of their future applications.

Phase change materials (PCMs) are an efficient alternative to store and release heat at a specific range of temperature. Here PCMs and heat enhancement methodologies for PCM storage are reviewed. A short overview of PCMs and their applications is presented in addition to the progress during the last 10 years. Heat enhancement techniques, that is, extended surfaces, multiple and composite PCMs, and encapsulation techniques, are presented along with a statistical overview of studies during 2016–2021. The importance of various fin and storage tank geometries (extended surfaces) is discussed in detail. Advancement in the latest heat enhancement techniques such as use of nano‐enhanced PCMs is presented. Recommendations for future research are provided.This article is categorized under: Emerging Technologies > Energy Storage Sustainable Energy > Energy Efficiency