Rosa Malena Fernandes Lima
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Rosa Malena Fernandes Lima has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Versiane Albis Leão
Universidade Federal de Ouro Preto
4 shared publications Deisiane Ferreira Lelis
Engenharia de Minas, Universidade Federal de Ouro Preto-Campus Morro do Cruzeiro, Ouro Preto, Brazil
2 shared publicationsGeriane Macedo Rocha
2 shared publicationsMargarida Márcia Fernandes Lima
2 shared publications- Alexandro Fortes Simões da Silva1 shared publication
Amélia de Souza Correa
Univ Fed Ouro Preto, Dept Min Engn, Campus Morro Cruzeiro S-N, BR-35400000 Ouro Preto, MG, Brazil
1 shared publication
Latest Publications
- Open Access
- 24 June 2026
- Published by Springer Nature in Discover Applied Sciences
- Vol. 8 (9)
Soybean-oil based collector in the flotation of spodumene from other silicates
- 24 June 2026
- Published by Springer Nature in Discover Applied Sciences
- Vol. 8 (9)
Open AccessSoybean-oil based collector in the flotation of spodumene from other silicates
- Open Access
- 3 February 2025
- Published by Brazilian Journals in Caderno Pedagógico
- Vol. 22 (4) , e13873
Evaluation of the technical feasibility of replacing natural limestone aggregate by iron ore tailing in the production of adhesive mortar
In this study, the replacement of natural limestone (NLA), widely used in the manufacture of adhesive mortars, by iron ore tailings (IOT), an abundant and underutilized material with great potential for application in cement products, was analyzed. The detailed characterization of IOT and NLA was performed through physical, morphological, mineralogical and chemical tests, ensuring the understanding of the fundamental properties of both materials. Adhesive mortar formulations were developed with NLA replacement percentages for IOT of 0% (reference), 20%, 40%, 60% and 100%, following the specific Brazilian standards for adhesive mortars. The experimental results confirmed the technical feasibility of fully replacing natural aggregate with IOT, both in ACII and ACIII mortars, characterized by their high added value. This initiative reinforces sustainability in the mining and construction sectors, by promoting the reuse of waste and reducing the environmental impact associated with the inadequate disposal of these materials, contributing to the circular economy.
- 3 February 2025
- Published by Brazilian Journals in Caderno Pedagógico
- Vol. 22 (4) , e13873
Open AccessEvaluation of the technical feasibility of replacing natural limestone aggregate by iron ore tailing in the production of adhesive mortar
In this study, the replacement of natural limestone (NLA), widely used in the manufacture of adhesive mortars, by iron ore tailings (IOT), an abundant and underutilized material with great potential for application in cement products, was analyzed. The detailed characterization of IOT and NLA was performed through physical, morphological, mineralogical and chemical tests, ensuring the understanding of the fundamental properties of both materials. Adhesive mortar formulations were developed with NLA replacement percentages for IOT of 0% (reference), 20%, 40%, 60% and 100%, following the specific Brazilian standards for adhesive mortars. The experimental results confirmed the technical feasibility of fully replacing natural aggregate with IOT, both in ACII and ACIII mortars, characterized by their high added value. This initiative reinforces sustainability in the mining and construction sectors, by promoting the reuse of waste and reducing the environmental impact associated with the inadequate disposal of these materials, contributing to the circular economy.
- 10 March 2024
- Published by Taylor & Francis in Mineral Processing and Extractive Metallurgy Review
- Vol. 45 (8) , 950-956
Effect of Sodium Hexametaphosphate on Flotation of Quartz and Hematite with Starch/Etheramine in the Presence of Ca and Mg Ions
- 10 March 2024
- Published by Taylor & Francis in Mineral Processing and Extractive Metallurgy Review
- Vol. 45 (8) , 950-956
Effect of Sodium Hexametaphosphate on Flotation of Quartz and Hematite with Starch/Etheramine in the Presence of Ca and Mg Ions
- 2 October 2023
- Published by Elsevier in Journal of Building Engineering
- Vol. 79
Alkaline activation for production of slag-based binders from the manufacture of manganese ferroalloys
- 2 October 2023
- Published by Elsevier in Journal of Building Engineering
- Vol. 79
Alkaline activation for production of slag-based binders from the manufacture of manganese ferroalloys
- 8 July 2023
- Published by Elsevier in Minerals Engineering
- Vol. 201
Effect of dolomite on cationic reverse flotation of iron ore with amide-amine
- 8 July 2023
- Published by Elsevier in Minerals Engineering
- Vol. 201
Effect of dolomite on cationic reverse flotation of iron ore with amide-amine
- 25 May 2022
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 57 (16) , 2625-2634
Concentration of oxidized Brazilian zinc ore by flotation: comparative study between anionic and cationic routes
In this work, a mineralogical characterization by X-ray diffractometry and thermogravimetric analysis of a new Brazilian zinc ore sample was performed. The mineralogical semi-quantification, conducted by normative calculation of the identified minerals, using their theoretical chemical formulas and the contents determined in the chemical analyses was as follows: smithsonite (20.3%), goethite (49.6%), kaolinite (12%), quartz (6.2%), cerussite (3.0%), chlorite (4.0%), dolomite (0.5%) and others (4.4%). Subsequently, bench flotation tests were executed, using sodium oleate (anionic route) and amine (cationic route) as smithsonite collectors. Sodium silicate was used as a depressant of the gangue minerals in both routes tested. These studies showed that the anionic route (30.1% Zn in concentrate and 83% Zn recovery) performed better than the cationic route (17.5% Zn in concentrate and 46.3% Zn recovery). Considering the mineralogical composition of the concentrates obtained in the best flotation results, associated with physicochemical studies published in the literature with the identified minerals, it was evidenced that the difference in performance between the tested routes is due to the influence of ions from the dissolution of carbonates present in the ore on the surface properties of the main gangue minerals (goethite and silicates), especially for the cationic route.
- 25 May 2022
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 57 (16) , 2625-2634
Concentration of oxidized Brazilian zinc ore by flotation: comparative study between anionic and cationic routes
In this work, a mineralogical characterization by X-ray diffractometry and thermogravimetric analysis of a new Brazilian zinc ore sample was performed. The mineralogical semi-quantification, conducted by normative calculation of the identified minerals, using their theoretical chemical formulas and the contents determined in the chemical analyses was as follows: smithsonite (20.3%), goethite (49.6%), kaolinite (12%), quartz (6.2%), cerussite (3.0%), chlorite (4.0%), dolomite (0.5%) and others (4.4%). Subsequently, bench flotation tests were executed, using sodium oleate (anionic route) and amine (cationic route) as smithsonite collectors. Sodium silicate was used as a depressant of the gangue minerals in both routes tested. These studies showed that the anionic route (30.1% Zn in concentrate and 83% Zn recovery) performed better than the cationic route (17.5% Zn in concentrate and 46.3% Zn recovery). Considering the mineralogical composition of the concentrates obtained in the best flotation results, associated with physicochemical studies published in the literature with the identified minerals, it was evidenced that the difference in performance between the tested routes is due to the influence of ions from the dissolution of carbonates present in the ore on the surface properties of the main gangue minerals (goethite and silicates), especially for the cationic route.
- Open Access
- 24 February 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 18, 223-230
Reverse cationic flotation of iron ore by amide-amine: bench studies
- 24 February 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 18, 223-230
Open AccessReverse cationic flotation of iron ore by amide-amine: bench studies
- Open Access
- 30 September 2021
- Published by Instituto Federal de Educacao, Ciencia e Tecnologia do Rio Grande do Norte (IFRN) in HOLOS
- Vol. 6 (6) , 1-16
CARACTERIZAÇÃO TECNOLÓGICA DE METAPIROXENITO DA FORMAÇÃO CÓRREGO DOS BOIADEIROS, NOVA LIMA (MG), BRASIL
Rochas e minerais industriais são materiais aplicados na produção de uma grande variedade de produtos, usados pela sociedade moderna. Um mesmo mineral ou rocha industrial pode ter diversas aplicações, dependendo de suas propriedades físicas, mineralógicas e químicas. O presente estudo teve como objetivo efetuar a caracterização tecnológica de uma amostra de metapiroxenito, proveniente da formação Córrego dos Boiadeiros, localizado no Quadrilátero Ferrífero, MG (Brasil), visando verificar possíveis aplicações industriais para o mesmo. Fluorescência de raios X foi utilizada para determinar os teores dos seguintes óxidos: 0,06% TiO2, 8,2% Fe2O3, 24,1% MgO, 2,1% Al2O3, 48,7% SiO2 e 1,8% CaO. Na caracterização mineralógica por difração de raios X, microscopia ótica, MEV/EDS e termogravimetria foram identificados os seguintes minerais: antigorita, clorita, cromita, ilmenita, magnetita, rutilo, talco e tremolita. Para os testes preliminares de concentração, o material usado (-147?m) apresentou 32% de partículas na fração -37?m com d50 igual a 74?m. Para o campo magnético de 3575 Gauss e fração granulométrica -74?m a recuperação em massa foi de 96,4% e alvura igual a 61,9% para o produto não magnético. Embora os ensaios de separação magnética não tenham gerado concentrados enriquecidos em talco, os produtos não magnéticos apresentaram especificações para as seguintes aplicações: papel (papel de parede e embalagem), inseticida e fertilizante.
- 30 September 2021
- Published by Instituto Federal de Educacao, Ciencia e Tecnologia do Rio Grande do Norte (IFRN) in HOLOS
- Vol. 6 (6) , 1-16
Open AccessCARACTERIZAÇÃO TECNOLÓGICA DE METAPIROXENITO DA FORMAÇÃO CÓRREGO DOS BOIADEIROS, NOVA LIMA (MG), BRASIL
Rochas e minerais industriais são materiais aplicados na produção de uma grande variedade de produtos, usados pela sociedade moderna. Um mesmo mineral ou rocha industrial pode ter diversas aplicações, dependendo de suas propriedades físicas, mineralógicas e químicas. O presente estudo teve como objetivo efetuar a caracterização tecnológica de uma amostra de metapiroxenito, proveniente da formação Córrego dos Boiadeiros, localizado no Quadrilátero Ferrífero, MG (Brasil), visando verificar possíveis aplicações industriais para o mesmo. Fluorescência de raios X foi utilizada para determinar os teores dos seguintes óxidos: 0,06% TiO2, 8,2% Fe2O3, 24,1% MgO, 2,1% Al2O3, 48,7% SiO2 e 1,8% CaO. Na caracterização mineralógica por difração de raios X, microscopia ótica, MEV/EDS e termogravimetria foram identificados os seguintes minerais: antigorita, clorita, cromita, ilmenita, magnetita, rutilo, talco e tremolita. Para os testes preliminares de concentração, o material usado (-147?m) apresentou 32% de partículas na fração -37?m com d50 igual a 74?m. Para o campo magnético de 3575 Gauss e fração granulométrica -74?m a recuperação em massa foi de 96,4% e alvura igual a 61,9% para o produto não magnético. Embora os ensaios de separação magnética não tenham gerado concentrados enriquecidos em talco, os produtos não magnéticos apresentaram especificações para as seguintes aplicações: papel (papel de parede e embalagem), inseticida e fertilizante.
- 30 July 2021
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 38 (5) , 2195-2207
Selective Flotation of Quartz from Hematite by Amide-Amine: Fundamental Studies
- 30 July 2021
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 38 (5) , 2195-2207
Selective Flotation of Quartz from Hematite by Amide-Amine: Fundamental Studies
- 25 May 2021
- Published by Taylor & Francis in Mineral Processing and Extractive Metallurgy Review
- Vol. 43 (6) , 720-727
Quartz and Hematite Activation by Zn, Ca and Mg Ions in the Cationic Flotation Route for Oxidized Zinc Ore
Anionic, cationic and cationic/anionic flotation is widely used in the concentration process for low-grade oxidized zinc ores. In the cationic flotation route, sodium silicate is used as a depressant for gangue minerals and amine as a collector for zinc minerals previously activated by sodium sulfide. However, the presence of polyvalent ions in aqueous solution can affect the surface properties of the various minerals and consequently, the selectivity of the process. This study evaluated the effect of Zn, Ca, and Mg ions, originated by the solubility of smithsonite and dolomite, on the surface properties of quartz and hematite. Microflotation tests showed the inefficiency of sodium silicate as a depressant for quartz in aqueous solution even when Zn, Ca, and Mg ions were not present. Activation of hematite by Zn ions was observed, impeding the separation of smithsonite and hematite (iron oxide). Results obtained from the microflotation and zeta potential tests were analyzed based on the speciation diagrams of the reagents and ions studied, as well as published studies.
- 25 May 2021
- Published by Taylor & Francis in Mineral Processing and Extractive Metallurgy Review
- Vol. 43 (6) , 720-727
Quartz and Hematite Activation by Zn, Ca and Mg Ions in the Cationic Flotation Route for Oxidized Zinc Ore
Anionic, cationic and cationic/anionic flotation is widely used in the concentration process for low-grade oxidized zinc ores. In the cationic flotation route, sodium silicate is used as a depressant for gangue minerals and amine as a collector for zinc minerals previously activated by sodium sulfide. However, the presence of polyvalent ions in aqueous solution can affect the surface properties of the various minerals and consequently, the selectivity of the process. This study evaluated the effect of Zn, Ca, and Mg ions, originated by the solubility of smithsonite and dolomite, on the surface properties of quartz and hematite. Microflotation tests showed the inefficiency of sodium silicate as a depressant for quartz in aqueous solution even when Zn, Ca, and Mg ions were not present. Activation of hematite by Zn ions was observed, impeding the separation of smithsonite and hematite (iron oxide). Results obtained from the microflotation and zeta potential tests were analyzed based on the speciation diagrams of the reagents and ions studied, as well as published studies.