Paolo Morandi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Paolo Morandi has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Guido Magenes
Department of Civil Engineering and Architecture (DICAr), University of Pavia, Pavia, Italy
20 shared publications - Luca Albanesi
Department of Construction and Infrastructure, EUCENTRE Foundation, Pavia, Italy
7 shared publications - Carlo Filippo Manzini
Department of Construction and Infrastructure, EUCENTRE Foundation, Pavia, Italy
6 shared publications - Riccardo Raimondo Milanesi
Department of Civil Engineering and Architecture, University of Pavia, Pavia, Italy
6 shared publications S. Hak
3 shared publications- Sanja Hak
Basler & Hofmann, Zürich, Switzerland
3 shared publications
Latest Publications
- 13 October 2026
- Published by Editora Cubo in Masonry International
- Vol. 37 (2) , 37203
In-plane seismic performance of different ductile masonry infill systems for resilient RC buildings
Masonry infilled reinforced concrete (RC) frames constitute a large portion of the global building stock. Although masonry infills are commonly treated as non-structural elements in seismic design, extensive experimental evidence and post-earthquake observations have demonstrated their significant influence on the structural response and their high vulnerability. Traditional non-ductile URM infills, constructed in full contact with the surrounding frame, may lead to detrimental in-plane and out-of-plane failure mechanisms (in particular the weak/slender ones), as well as to adverse interaction effects on RC members. To overcome these limitations, recent research has focused on the development of innovative ductile infill systems, including solutions with sliding or deformable joints, aimed at controlling damage and reducing infill–frame interaction while maintaining out-of-plane stability. The evolution of these systems has recently been reflected in updated seismic codes, such as EC8-1-2 (2025), which introduces a clear definition of ductile masonry infills and provides specific design criteria. In this study, several experimentally validated ductile infill systems are analysed in detail, with particular focus on their in-plane deformation capacity, expressed in terms of inter-storey drift ratio at different limit states (Operational, Damage, and Severe Damage). A consistent definition of these limit states is proposed based on both qualitative damage observations and quantitative criteria. A statistical analysis is carried out using a comprehensive dataset of in-plane cyclic tests on different typologies of ductile infills. The resulting drift capacities are compared with the non-ductile infills and with limits included in EC8-1-2 (2025) and NTC 2018 and results are discussed critically. The results demonstrate that ductile infill systems significantly enhance in-plane performance compared to traditional non-ductile URM infills. These features make them an effective solution for improving the seismic resilience of RC buildings, with increasing applicability in practice supported by recent code developments.
- 13 October 2026
- Published by Editora Cubo in Masonry International
- Vol. 37 (2) , 37203
In-plane seismic performance of different ductile masonry infill systems for resilient RC buildings
Masonry infilled reinforced concrete (RC) frames constitute a large portion of the global building stock. Although masonry infills are commonly treated as non-structural elements in seismic design, extensive experimental evidence and post-earthquake observations have demonstrated their significant influence on the structural response and their high vulnerability. Traditional non-ductile URM infills, constructed in full contact with the surrounding frame, may lead to detrimental in-plane and out-of-plane failure mechanisms (in particular the weak/slender ones), as well as to adverse interaction effects on RC members. To overcome these limitations, recent research has focused on the development of innovative ductile infill systems, including solutions with sliding or deformable joints, aimed at controlling damage and reducing infill–frame interaction while maintaining out-of-plane stability. The evolution of these systems has recently been reflected in updated seismic codes, such as EC8-1-2 (2025), which introduces a clear definition of ductile masonry infills and provides specific design criteria. In this study, several experimentally validated ductile infill systems are analysed in detail, with particular focus on their in-plane deformation capacity, expressed in terms of inter-storey drift ratio at different limit states (Operational, Damage, and Severe Damage). A consistent definition of these limit states is proposed based on both qualitative damage observations and quantitative criteria. A statistical analysis is carried out using a comprehensive dataset of in-plane cyclic tests on different typologies of ductile infills. The resulting drift capacities are compared with the non-ductile infills and with limits included in EC8-1-2 (2025) and NTC 2018 and results are discussed critically. The results demonstrate that ductile infill systems significantly enhance in-plane performance compared to traditional non-ductile URM infills. These features make them an effective solution for improving the seismic resilience of RC buildings, with increasing applicability in practice supported by recent code developments.
- Open Access
- 23 July 2026
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 55 (13) , 3302-3318
Energy‐Based Characterisation of Earthquake Damage in Masonry Infills Through Combined In‐Plane and Out‐of‐Plane Experimental Tests
The seismic capacity of structural systems/members is usually defined in terms of deformation thresholds. Although this is effective in many circumstances, disregarding cumulative quantities such as hysteretic energy may be ineffective when low‐cycle fatigue is relevant (e.g., long‐duration ground motions, very soft soils, ground‐motion sequences). This paper presents the outcomes of an experimental campaign designed to explore the suitability of hysteretic energy thresholds to characterise damage. To do so, three nominally identical masonry infill panels were subjected to in‐plane (IP), quasi‐static, cyclic displacement‐controlled loads generating a moderate level of damage, followed by out‐of‐plane (OOP), dynamic shaking‐table tests amplified until collapse. The study investigated the effect of the IP hysteretic energy dissipation on the observed IP damage state, and the subsequent OOP collapse capacity. Different IP loading protocols were designed to induce the same peak amplitude‐based engineering demand parameters (EDPs) while modulating the energy‐based demands. In the IP phase, two specimens showed a damage pattern dominated by sliding along two to three horizontal cracks, while the third specimen was dominated by a diagonal, strut‐like failure. For the sliding‐dominated specimens, the IP hysteretic energy showed signs of a positive correlation with the level of damage, and, in turn, a possible negative correlation with the peak floor acceleration leading to complete OOP collapse. On the one hand, further complementary experimental tests and/or refined numerical analyses are needed to generalise the trend highlighted here. On the other hand, the presented results pave the way for using energy‐based EDPs for state‐dependent seismic fragility assessment methodologies, thus allowing a refined consideration of damage accumulation.
- 23 July 2026
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 55 (13) , 3302-3318
Open AccessEnergy‐Based Characterisation of Earthquake Damage in Masonry Infills Through Combined In‐Plane and Out‐of‐Plane Experimental Tests
The seismic capacity of structural systems/members is usually defined in terms of deformation thresholds. Although this is effective in many circumstances, disregarding cumulative quantities such as hysteretic energy may be ineffective when low‐cycle fatigue is relevant (e.g., long‐duration ground motions, very soft soils, ground‐motion sequences). This paper presents the outcomes of an experimental campaign designed to explore the suitability of hysteretic energy thresholds to characterise damage. To do so, three nominally identical masonry infill panels were subjected to in‐plane (IP), quasi‐static, cyclic displacement‐controlled loads generating a moderate level of damage, followed by out‐of‐plane (OOP), dynamic shaking‐table tests amplified until collapse. The study investigated the effect of the IP hysteretic energy dissipation on the observed IP damage state, and the subsequent OOP collapse capacity. Different IP loading protocols were designed to induce the same peak amplitude‐based engineering demand parameters (EDPs) while modulating the energy‐based demands. In the IP phase, two specimens showed a damage pattern dominated by sliding along two to three horizontal cracks, while the third specimen was dominated by a diagonal, strut‐like failure. For the sliding‐dominated specimens, the IP hysteretic energy showed signs of a positive correlation with the level of damage, and, in turn, a possible negative correlation with the peak floor acceleration leading to complete OOP collapse. On the one hand, further complementary experimental tests and/or refined numerical analyses are needed to generalise the trend highlighted here. On the other hand, the presented results pave the way for using energy‐based EDPs for state‐dependent seismic fragility assessment methodologies, thus allowing a refined consideration of damage accumulation.
- Open Access
- 7 July 2026
- Published by Elsevier in SSRN Electronic Journal
Seismic vulnerability assessment of Italian road bridges through the definition of fragility curves for bridge taxonomies
Italian roadway network is managed by several authorities including ANAS (Azienda Nazionale Autonoma delle Strade), regional and provincial administrations, and managing concessionaires of motorways. This network comprises approximately 30,000–35,000 km of main roads and highways, encompassing tens of thousands of bridges and viaducts distributed across the country. Given the large number of infrastructure assets, many of which were constructed before the era of digital record-keeping, it is virtually impossible to perform an ad-hoc seismic vulnerability assessment foreachfor individual bridge due to limited data availability. To address this challenge, a study commissioned by the Italian Department of Civil Protection (IDCP) was carried out at the EUCENTRE Foundation to classify bridges into taxonomies. For each taxonomy, a set of fragility curves, newly developed within the study, was associated. The aim of this research is to identify, within the framework of a multi-level, large-scale seismic vulnerability assessment, the most critical cases in the extensive bridge stock, thereby determining where more detailed analyses are necessary and to defining priorities of intervention. In this paper, the assumptions used for the bridge classification, the numerical models adopted for the derivation of the fragility curves, and the parameters of the resulting curves are reported and discussed.
- 7 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSeismic vulnerability assessment of Italian road bridges through the definition of fragility curves for bridge taxonomies
Italian roadway network is managed by several authorities including ANAS (Azienda Nazionale Autonoma delle Strade), regional and provincial administrations, and managing concessionaires of motorways. This network comprises approximately 30,000–35,000 km of main roads and highways, encompassing tens of thousands of bridges and viaducts distributed across the country. Given the large number of infrastructure assets, many of which were constructed before the era of digital record-keeping, it is virtually impossible to perform an ad-hoc seismic vulnerability assessment foreachfor individual bridge due to limited data availability. To address this challenge, a study commissioned by the Italian Department of Civil Protection (IDCP) was carried out at the EUCENTRE Foundation to classify bridges into taxonomies. For each taxonomy, a set of fragility curves, newly developed within the study, was associated. The aim of this research is to identify, within the framework of a multi-level, large-scale seismic vulnerability assessment, the most critical cases in the extensive bridge stock, thereby determining where more detailed analyses are necessary and to defining priorities of intervention. In this paper, the assumptions used for the bridge classification, the numerical models adopted for the derivation of the fragility curves, and the parameters of the resulting curves are reported and discussed.
- 2 April 2026
- Published by Springer Nature
- p. 2083-2093
Dynamic Testing of a Masonry Bell Tower Equipped with AMD System and Strengthened with FRCM
- 2 April 2026
- Published by Springer Nature
- p. 2083-2093
Dynamic Testing of a Masonry Bell Tower Equipped with AMD System and Strengthened with FRCM
- 15 March 2026
- Published by Springer Nature
- p. 89-102
Experimental In-Plane Seismic Response of Masonry Walls Strengthened with Innovative Modular Steel Solutions
- 15 March 2026
- Published by Springer Nature
- p. 89-102
Experimental In-Plane Seismic Response of Masonry Walls Strengthened with Innovative Modular Steel Solutions
- 18 December 2025
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 24 (3) , 1635-1683
Experiment-based definition of limit states and derivation of in-plane drift capacity of brick and block URM walls for seismic design and assessment
- 18 December 2025
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 24 (3) , 1635-1683
Experiment-based definition of limit states and derivation of in-plane drift capacity of brick and block URM walls for seismic design and assessment
- 2 September 2025
- Published by Elsevier in Structures
- Vol. 80
In-plane cyclic tests of unexplored URM walls: “Doppio UNI” and “header bond” clay brick typologies
- 2 September 2025
- Published by Elsevier in Structures
- Vol. 80
In-plane cyclic tests of unexplored URM walls: “Doppio UNI” and “header bond” clay brick typologies
- 27 December 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 100
Dynamic shaking table out-of-plane tests on weak masonry infills with and without previous in-plane loading
- 27 December 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 100
Dynamic shaking table out-of-plane tests on weak masonry infills with and without previous in-plane loading
- 21 September 2023
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 21 (14) , 6317-6365
SAM-II: development and validation of an EF-based program for seismic pushover analysis of masonry buildings
- 21 September 2023
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 21 (14) , 6317-6365
SAM-II: development and validation of an EF-based program for seismic pushover analysis of masonry buildings
- 6 July 2023
- Published by Taylor & Francis in Journal of Earthquake Engineering
- Vol. 28 (5) , 1331-1357
Experimental In-Plane Seismic Performance of an Innovative Steel Modular Strengthening System for URM Walls
- 6 July 2023
- Published by Taylor & Francis in Journal of Earthquake Engineering
- Vol. 28 (5) , 1331-1357
Experimental In-Plane Seismic Performance of an Innovative Steel Modular Strengthening System for URM Walls